IMPORTANT This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read. Installation Manual ® Power8 TM S E C U R I T Y S Y S T E M PC5OO5 Version 3.2 DLS-3 v1.
New Features PC5200 Support The PC5005 v3.2 and higher supports the new PC5200 Power Supply module. See PC5200 Power Supply Output Module, Pg 2. PC5936 Support The PC5005 v3.2 and higher supports the PC5936 15-station audio matrix module. See PC5936 Audio Interface Module, Pg 2. No Activity Arming (by Partition) This feature enables the system (or partition) to arm if there is no zone activity for a programmed time period. See [191]-[198] - No-Activity Timer (Partition 1-8), Pg 33.
Ta ble of Contents Section 1: Introduction 1 1.1 About the Power8 System ............................................ 1 1.2 About the Power8 Manual Set ..................................... 1 1.3 Main Panel Specifications ............................................. 1 1.4 Additional Devices ........................................................ 2 3.5 Section 4: Keypad Commands 11 4.1 Arming and Disarming ................................................ 11 4.2 [✱] Commands ..............................
PC5005 Wiring Diagram iii
F C C CO MP L I A N CE S TATE M E NT CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Section 1: Introduction 1.
System Supervision Features The PC5005 continuously monitors a number of possible trouble conditions including: • AC Power Failure • Trouble by Zone • Fire Trouble • Telephone Line Trouble • Low Battery Condition • Bell Output Trouble • Loss of Internal Clock • AUX Power Supply Fault • Tamper by Zone • Failure to Communicate • Module Fault (Supervisory or Tamper) • Camera Troubles via DLM-4L False Alarm Prevention Features • Audible Exit Delay • Audible Exit Fault • Urgency on Entry Delay • Quick Exit • Swi
Introduction: 1.4 Additional Devices Backplates There are two different backplates available for keypads to mount an Audio Station next to a keypad: requires a separate battery and transformer (See Links1000 Cellular Communicator in Section 5). T-Link Local Area Network Communicator The T-Link Local Area Network Communicator provides an efficient method of communicating via a Local Area Network (LAN). See the T-Link Installation Manual for more details.
Section 2: Installation and Wiring The following sections provide a complete description of how to wire and configure devices and zones. Step 10 Testing the System Test the panel completely to ensure that all features and functions are operating as programmed. 2.1 Installation Steps The following steps are provided to assist with the installation of the panel. It is suggested that you read over this section briefly to get an overall understanding of the order of installation.
• shielded wire is not necessary unless wires are run in an area that may present excessive RF noise or interference PGM2 is a high current output (300mA) and operates similarly to PGM1. If more than 300 mA of current is required, a relay must be used. Refer to the diagram. Zone Input Terminals - Z1 to Z8 Each detection device must be connected to a zone on the control panel. It is suggested that each zone have one detection device however it is possible to wire multiple detection devices to the same zone.
System Outputs (all 12 VDC) PC5005 VAUX: BELL: PC5200 VAUX: PC5204 VAUX: PC5208 VAUX: 3. Enter [1] to [5] to select function key to program. 4. Enter a 2-digit number for function key option - [00] to [30]. 5. Continue from step 3 until all function keys are programmed. 6. Press [#] key twice to exit Installer Programming. For a complete list of Function Key options, see section 4.3 ’Function Keys ’. 550 mA.
Installation and Wiring: 2.7 Removing Modules If a module is connected but does not show as being present, it may be due to any of the following reasons: • it is not connected to the Keybus • there is a Keybus wiring problem • the module is more than 1,000'/305m from the panel • the module does not have enough power • the PC5132 does not have any devices added 2.7 Removing Modules If a module is no longer required on the system, the panel must be told to stop supervising the module. To do this: 1.
For a complete description of how fire zones operate, see section 5.3 ’Basic Programming PWS Sect 3 ’. Fire Zone Wiring - 2-wire Smoke Detectors If PGM 2 has been programmed for 2-wire smoke detector connection (see section 5.3 ’Basic Programming PWS Sect 3 ’) , the detectors must be wired according to the following diagram: For a complete description of how fire zones operate, see section 5.3 ’Basic Programming PWS Sect 3 ’.
Section 3: How to Program The following section of the manual describes how to enter Installer Programming and how to program the various sections. NOTE: It is extremely important that you read the following section of the manual to completely understand how to program the panel. The following table indicates which number should be pressed to enter the corresponding HEX digit: 1=A 2=B 3=C 4=D 5=E 6=F After the correct HEX digit is entered the Ready light will continue to flash.
3.5 Viewing Programming LED and LCD5501Z Keypads Any programming section can be viewed from an LED or LCD5501Z keypad. When a programming section is entered, the keypad will immediately display the first digit of information programmed in that section. The keypad displays the information using a binary format, according to the following chart: See Hex data entry instructions Press any of the emergency keys (Fire, Auxiliary or Panic) to advance to the next digit.
Section 4: Keypad Commands Use any system keypad to enter commands, or to program the Power8 security system. The LED keypad uses function and zone indicator lights to represent alarm functions and status. The LCD keypad provides a written description on the liquid crystal display and uses function indicator lights to communicate alarm status to the user. The Power8 User’s Guide provides basic directions for arming and disarming the system, bypassing zones and performing user functions from the keypads.
Viewing the Event Buffer The following is the procedure for viewing the event buffer through the LCD keypad: • Step 1 - Enter [*] [6] [Master Code] • Step 2 - Select ‘View Event Buffer’ The keypad will display the Event Number, Partition, Time and Date of the event in question. Use the [*] key to toggle between this information and the event itself. Use the arrow keys (<>) to scroll through the events in the buffer. When you have finished viewing the event buffer press the [#] key to exit.
Light Trouble 6 Zone Tamper: A zone configured for Double End Of Line resistor supervision has a tamper condition, or the tamper switch is open on a wireless device. When a tamper condition occurs, the keypad(s) will start to beep (if the system is armed, an alarm will occur). Press [6] while in the Trouble mode to view the affected zones. If a zone is tampered or faulted, it must be fully restored to clear the trouble. 7 Device Low Battery: A wireless device has a low battery condition.
the Auto-arm Schedule menu. See section 4.4 ‘Global and Partition Keypad Operation‘ for more information. NOTE: Only LCD5500 v2.0 or greater keypads support the [*][6][3] menu option. • [4] - System Test When [4] is pressed the panel will perform the following. For step-by-step instructions on performing a system test, see the Power8 User’s Guide (“Full System Test”).
Keypad Commands: 4.3 Function Keys The entry delay can be activated or deactivated at any time while the system is armed by pressing [*][9]. NOTE: Global Delay zones will always have an entry delay, even if the system is armed using [*][9]. [*] [0] Quick Arm If the Quick Arm Enable option is enabled the panel can be armed by entering [*][0]. This is a useful method of arming a Partition when someone without a access code will be required to arm a Partition.
[13] - [*]+[7]+[1] Command Output Option 1 This function key provides the user with a simple method for activating a PGM Output programmed as Command Output Option 1 (see section 5.8 Programmable Output Programming PWS Sect 8). By default, after this key is pressed a valid access code must be entered (see section ’[*] [7] Command Output Functions ’). instructions on zone bypassing and programming Bypass Groups, see the Power8 User’s Guide.
Keypad Commands: 4.5 Features Available for the LCD5500Z 4.5 Features Available for the LCD5500Z These features are only available for LCD5500Z keypads with zone inputs: Automatic Scrolling of Open Zones The LCD5500Z keypad (v3.1 and higher) automatically scrolls through open zones while the keypad is idle. This feature, if enabled, will override the clock display. This option can be programmed in LCD programming section [076], Option [8].
Section 5: Programming Sections The structure of this section corresponds with the structure of the Programming Worksheets (PWS) and is intended to be used with them. Paragraph 5.1 corresponds with section 1 etc. Table 5-1 references the paragraphs in this section with the corresponding location in the programming worksheets. Table 5-1 - SECTION 5 CONTENTS Sect Item Sect Item Para 5.1 For the Record 378 Test Transmission Time of Day Para 5.
Programming Sections: 5.1 For the Record PWS Sect 1 5.1 For the Record PWS Sect 1 This section identifies the Client, Installation Date, Installer Code, Hardware configuration and Programming summary for each zone. Remove these pages and retain for reference. 5.2 Keypad Programming PWS Sect 2 Refer to section 2.6 ‘Keypad Assignment’ 5.3 Basic Programming PWS Sect 3 [001]-[004] - Zone Definitions These sections require 16 two digit entries. Each two digit number entered determines how a zone will operate.
[001]-[004] ZONE DEFINITIONS Option Zone Type Description 25 Interior Delay Zone The Interior Delay Zone is normally used with motion detectors and has a standard exit delay time. If the panel is armed, and a Delay zone is violated during the Exit Delay (or the Away function key is used), the Interior Delay Zone will be active at the end of the Exit Delay. This zone will cause an instant alarm when violated. This zone type will follow the Entry Delay time provided that a Delay zone is violated first.
Programming Sections: 5.3 Basic Programming PWS Sect 3 [007] - Master Code • The first two entries of Section [010] are used to program the last two outputs on the PC5005, and the first two on the PC5208. • Section [010] is used to program the PGM outputs on the PC5208. • Section [011] is used to program the PGM outputs on the PC5204. Programming any of the outputs is a three step process: 1. Select an option from the list below for the PGM output. 2. Select the output attributes for the PGM output. 3.
[009] - [011] PROGRAMMABLE OUTPUT OPTIONS Option Output Description 10 Latched System Event (Strobe) This output will activate when any of the selected system events (alarms) occur on the system. In the armed state, the output will deactivate only once the system is disarmed. This output will activate when the programmed events occur on any partition.
Programming Sections: 5.3 Basic Programming PWS Sect 3 [012] - Keypad Lockout Options The panel can be programmed to ‘lockout’ keypads if a series of incorrect access code entries are made. After the Number of Invalid Codes Before Lockout has been reached the panel will lock out the keypad for the Lockout Duration and log the event to the event buffer. For the duration of the lockout the panel will sound an error tone when any key is pressed.
[013] FIRST SYSTEM OPTION CODES Option 1 2 3 4 5 6 Definition On/Off Description Zone Loop Type ON Normally Closed Loops. All zones are wired as normally closed circuits with returns connected to a COM terminal. The end of line resistor is not required. An alarm will be generated when the circuit is opened. OFF End of Line Resistors. All zones must be wired with an end of line resistor configuration, determined by Option 2 in this system. NOTE: The valid EOL value is 5600 Ohms (5.6KΩ Ω).
Programming Sections: 5.3 Basic Programming PWS Sect 3 5 Bell Squawk on Trouble ON Bell Squawks on Trouble. When there is a Trouble condition annunciated on the system keypads, the Bell will squawk 2 times every 10 seconds (as per the keypad buzzer). The Bell will be silenced when the keypad beeps are silenced (any key pressed on keypad). OFF No Bell Squawks on Trouble. 6 Audible Exit Beeps ON Audible Exit With Urgency. The keypad will sound a pulsing tone (once per second) during the Exit Delay.
[016] - FOURTH SYSTEM OPTION CODES Option Definition On/Off Description 1 AC Trouble Display ON AC Trouble Displayed. If AC power fails, the condition will be reported to the monitoring station and will be indicated as a Trouble condition on the system Keypads. OFF AC Trouble Not Displayed. If AC power fails, the condition will be reported, but the Trouble light will not be indicated on the system keypads. If [*][2] is entered to view the system troubles, Trouble #2 will still be displayed.
Programming Sections: 5.3 Basic Programming PWS Sect 3 Option 5 6 Definition On/Off Description Late To Close ON Late to Close Enabled. The panel will communicate and log a Late to Close event at the time programmed for auto-arm for each partition. This system toggle controls if the Late to Close Reporting Code is sent at the end of the auto-arm/Postpone Pre-alert.
Option Definition On/Off Description 3 Verbal Alarm ON Verbal Alarm is Enabled. The system will verbally annunciate audible zone alarms via their zone number (or programmed label) in conjunction with the Bell Outputs. This feature is available when the ESCORT5580 v3.0 and PC5936 v1.0) are used. This feature enables verbal annunciation of alarm conditions on the system.
Programming Sections: 5.4 Advanced Programming PWS Sect 4 5.4 Advanced Programming PWS Sect 4 [101]-[132] Zone Attributes The two sets of attributes (1-8 and 9-16) may be toggled by pressing [9] within any zone’s attribute section. If the Ready LED is on, the keypad is indicating Zone Attributes 1-8; if the Ready and Armed LED’s are on, the keypad is indicating Zone Attributes 9-16. The following options can be enabled or disabled by zone.
NOTE: If 000 is programmed in this section, either: The Police Code will transmit for any two different zone alarms during an armed-to-armed period or the new Cross Zoning feature will not work. This is not a valid entry for Cross Zoning. NOTE: Option[9], section [101]-[132] must be enabled for the Cross Zoning feature to function. Each zone has the ability to individually protect the intended area. Cross Zoning is NOT recommended for line security installations or on exit/entry zones.
Programming Sections: 5.6 Communicator Programming PWS Sect6 5.6 Communicator Programming PWS Sect6 [302] - Second Telephone Number Communicator - Account Codes The System Account Code will be used by the panel when communicating System events (e.g. Low Battery, Test Transmission). This account code can be up to six digits in length for the SIA Communications format. Only the SIA reporting format supports six-digit account codes.
[330]-[333] - Tamper Reporting Codes, Zones 1-32 If the panel is programmed for Double EOL zones (see section 2.10 "Zone Wiring") the panel will report a Zone Tamper Alarm Reporting Code if an open condition is present on a zone. A different reporting code can be programmed for each zone for identification. [334]-[337] - Tamper Reporting Codes, Zones 1-32 The Zone Tamper Restoral Reporting Code will be transmitted immediately when the tamper condition is restored.
Programming Sections: 5.6 Communicator Programming PWS Sect6 and transmit an Auxiliary Power Supply Trouble Restoral Reporting Code. TLM Restoral: the TLM Restoral Reporting Code will be transmitted immediately after the trouble is restored.
2. If the reporting code for an event is programmed as anything from [01] to [FE] the panel will send the programmed reporting code. 3. Bypassed zones will not be identified when partial closing the system. NOTE: The zone number for Zone Low Battery and Zone Fault events will not be identified when Programmed SIA is used. Periodic Test Transmission if any of the following conditions exist.
Programming Sections: 5.6 Communicator Programming PWS Sect6 Pulse Formats Depending on the pulse format selected the panel will communicate using the following: • 3/1, 3/2, 4/1 or 4/2 • 1400 or 2300 Hz handshake • 10 or 20 bits per second • non-extended The digit ‘0’ will send no pulses and is used as a filler.When programming account numbers enter four digits. When programming a three digit account number the fourth digit must be programmed as a plain ‘0’ which will act as a filler digit.
[351]-[376] - Communicator Call Directions For events from each Call Direction group the control panel can call 2 different phone numbers and use the LINKS as backup or as a redundant communicator for one or both numbers. The Third phone number can only be used as a backup or alternate of the first. Each report falls under one of the following 5 Groups: 1. Partition X Alarms & Restores 2. Partition X Openings & Closings 3. Partition X Tampers & Restores 4. System Maintenance Alarms & Restores 5.
Programming Sections: 5.6 Communicator Programming PWS Sect6 [377] - COMMUNICATION VARIABLES Swinger Shutdown (Alarms & Restores) This value defines the number of attempts (alarm and restore pairs) per zone that the communicator will make before it shuts down for that zone (“swinger shutdown”). Valid entries are 000 to 014. Different limits can be programmed for Zone Alarms, Zone Tampers and Maintenance signals.
[380] - FIRST COMMUNICATOR OPTION CODES Option 1 2 3 4 Communicator Code Communications Restore Transmission Dialing Method Switch to Pulse Dialing 5 3rd Phone Number Enable 6 3rd Phone Number 7 8 LINKS Dialing Delinquency On/Off Description ON Communicator Enabled. The system’s communicator will be enabled and all events with reporting codes will be reported to the monitoring station. Refer to the Telephone Number, Reporting Code and Call Direction Programming Sections.
Programming Sections: 5.6 Communicator Programming PWS Sect6 [381] - SECOND COMMUNICATOR OPTION CODES Option 3 Communicator Code SIA Reporting Codes 4 Closing Confirmation 5 Talk/Listen Options for Phone Number One/Three 6 Talk/Listen Options for Phone Number Two 7 Contact I.D. Reporting Codes 8 On/Off Description ON SIA Sends Programmed Rep. Codes. This option is for use with the SIA communication format.).
This 4-digit number can be used with long distance telephone numbers that are dialed through the LINKS Module. These codes are used for programming area codes in cases where a land line telephone number may be a local call, while the cellular telephone number dialed by the LINKS module is a long distance call. [393] - LINKS Special Function Preamble This special preamble is inserted before all other preambles. It is used for dialing such cellular numbers as #DAT and *DATA for reduced billing increments.
Programming Sections: 5.8 Programmable Output Programming PWS Sect 8 disconnected. If using the LINKS1000 with Call Back, you need to program the LINKS1000 Preamble with the downloading telephone number in order for the panel to call the computer correctly. NOTE: When uploading labels from LCD keypads, the DLS software will receive the labels only from the LCD keypad assigned to slot 8. In addition, version 1.0 and version 2.0 LCD keypads are not compatible on the same system.
NOTE: Attribute [3] must be ON for PGM output option [16]. Assigning Partitions to Programmable Outputs By default, all programmable outputs are assigned to partition 1. For programmable outputs to work on other par- titions, enable or disable the appropriate partitions in the Partition Assignment programming sections. PGM Output Partition Assignment . . . . . . . . .Sections [551] - [564] PGM Output timer . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programming Sections: 5.9 International Programming PWS Sect 9 [701] FIRST INTERNATIONAL OPTION CODES Option 1 2 3 4 5 International Code On/Off AC ON 50 Hz AC. - The incoming AC power cycles at 50 Hz. OFF 60 Hz AC. - This is the North American standard where the incoming AC power cycles at 60 Hz. ON The timebase is the internal crystal oscillator. In cases of unstable AC power input, the internal crystal can be used to keep the most accurate timebase. OFF The timebase is the AC power input.
[703] - Delay Between Dialing Attempts For standard (force) dialing, the panel will go off-hook, search for dialtone for 5 seconds, hang-up for 20 seconds, go off-hook, search for dialtone for 5 seconds, then dial. If there is no initial handshake recognized within 40 seconds, the panel will hang up. This programmable timer adds a delay before the next call is attempted, and is defaulted to 001 for a total of six seconds. 5.
Programming Sections: 5.11 Special Installer Instructions PWS Sect 11 Factory Default Main Panel (Hardware) 1. Remove AC and battery from the panel. 2. Remove all wires from the Zone 1 and PGM1 terminals. 3. With a piece of wire short the Zone 1 terminal to the PGM1 terminal. 4. Apply AC power to the main panel. 5. When Zone Light 1 is lit on the keypad the default is complete. 6. Remove AC power from the control 7. Reconnect all original wiring and power up the control.
Appendix A: Reporting Codes SIA Format - Level 2 (Hardcoded) The SIA communication format used in this product follows the level 2 specifications of the SIA Digital Communication Standard - October 1997. This format will send the Account Code along with its data transmission. The transmission will look similar to the following at the receiver: N Ri01 BA 01 N = New Event Ri01 = Partition /Area Identifier BA = Burglary Alarm 01 = Zone 1 NOTE: A system event will use the Area Identifier Ri00.
Automatic Dialer Contact ID Direction* Codes SIA Auto Rep Codes** Section # Reporting Code Code Sent When... [344] Special Opening Opening (disarming) using one of the following methods: key- O/C switch, maintenance code, DLS software, wireless key (4) AA [345]-[346] Battery Trouble/Rest. PC5005 battery is low/battery restored MA/R (3) A2 YT-00/YR-00 [345]-[346] AC Line Trouble/Rest.
Table 2: Contact ID Zone Alarm/Restoral Event Codes (as per SIA DCS: ‘Contact ID’ 01-1999): Table 3: SIA Format Automatic Zone Alarm/Restoral Codes Program any of these codes for zone alarms/restorals when using the standard (non-automatic) Contact ID reporting format.
WARNING Please Read Carefully Note to Installers This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring each item in this warning to the attention of the users of this system. Syst em Failures This system has been carefully designed to be as effective as possible. There are circumstances, however, involving fire, burglary, or other types of emergencies where it may not provide protection.
PC5005 Module Compatibility Module Compatible? Comments Classic Escort (VPM-1) DLM-1 DLM-4 v1.x DLM-4 v1.0L DLM-7 Escort5580 v3.0 LCD5500 v1.X No No No Yes No Yes Yes LCD5500Z v2.X LCD5501Z v1.x LCD5500Z v3.X LCD5501Z v2.x LCD5501Z32-433 LCD600 LED615 Links1000 v3.0 Links2150 v1.3W Links2450 v1.3 PC1555RKZ PC-16 Out PC5100 PC5108 PC5132 v1.X Yes Yes Yes Yes Yes No No Yes Yes Yes Yes No Yes No Yes PC5132 v2.X Yes PC5132 v3.X PC5200 PC5204 PC5208 PC5320 PC5400 Printer/DVACS Module v1.X to v2.
