Quick Guide to Power832 PC5015 For more detailed information, please refer to the Installation Manual and Programming Worksheets.
Features Table of Contents Features ................................................. 1 Installation ............................................. 2 Installing the Power832 Control Panel ........................................... 2 Wiring .................................................... 4 Wiring Keybus .............................. 4 Wiring 24-hr Devices .................... 5 Wiring PIRs .................................. 6 Wiring Fire Detectors ................... 7 Wiring SAB .....................
Features Features • • • • • • • • • • • • • • • • • • • • 8 on-board zones Expandable to 32 zones via 8 zone modules or wireless module Supports up to 8 keypads LED and LCD versions available Up to 14 programmable outputs All modules connected via 4-wire Keybus Uses normal alarm cable Modules can be wired star or daisy chain All modules are fully supervised 256 event log 20+ zone types Zones can be configured as NC, SEOL or DEOL 8 zone attributes 2 true partitions Common zones Built-in multi-channel comm
Features Installation Installing the Power832 Control Panel The following steps should be carried out in the order described below. This will help reduce the overall installation time. Before carrying out any installation work, it is always advisable to walk the site and check the proposed location of all the equipment you are intending to install. 1. Run all cables from the location of the detectors or modules back to the main control panel or zone expander units. 2.
Installation 5. Connect all modules on the Keybus using STAR or DAISY chain, red to red, black to black, yellow to yellow and green to green. 6. Connect all detection devices. 7. Connect the external sounder. 8. Insert the lid tamper and wire to the control panel. 9. Fit the battery into the control panel and connect the RED to RED and BLACK to BLACK. 10. Connect the control panel to the telephone line if monitoring or upload/download is required. 11.
Features Wiring Wiring Keybus The Keybus wiring is the most important part of the installation process of the Power832 and its associated modules. The Keybus is a simple 4wire connection between the main control panel and all modules connected to it. Do not use the Keybus cable for connection to any other devices: e.g., do not try to repower detectors or devices using the extra cores in a multi core cable. The Keybus is coloured RED, BLACK, YELLOW, GREEN.
Wiring Wiring 24-hr Devices The diagram below shows how to connect door contacts, break glass detectors and panic attack buttons to the Power832 using double end of line resistors (DEOL). Always follow the manufacturer’s instructions when installing such devices.
Wiring Wiring PIRs Although zones can be be wired as double end of line (DEOL), single end of line (SEOL) or normally closed, we recommend DEOL for all intrusion sensors and contacts. The panel actually comes defaulted as SEOL. DEOL means that two 5.6K resistors are installed at the sensor head as shown in the diagram below. These resistors are included with the panel. The resistors measure a loss in current caused by a tamper or other fault condition.
Wiring Wiring Fire Detectors The diagram below shows how smoke detectors should be connected to the Power832 control panel. Always check the manufacturer’s instructions for the detector. NOTE: Any zone which is programmed as fire will automatically be configured as SEOL. Therefore only 1 resistor needs to be installed and the contact should be normally open.
Wiring Wiring SAB These bell diagrams indicate how to connect various bells to the Power832. Take note that the strobe should be connected to PGM 2 and this is programmed as default for your strobe connection. The bell circuit on the Power832 is always supervised with a 1K resistor.
Wiring Connecting A NOVAGUARD 2+T Connecting A NOVAGUARD Delta Economy Wiring SAB 9
Features Telephones Telephone Connections The Power832 is a powerful communications device and it is important that you make the correct connections to the telephone line. The line may be connected in different ways for different applications. Connecting the Phone Line with Escort and Intercom NOTE: The control panel should always be the first device on the line. This is to ensure various features work correctly such as line seizure.
Features Power Up Initial Start Up Before turning on the mains power, make sure that all electrical connections are completed and all devices are connected correctly to the main PCB. The two YELLOW leads on the transformer should be securely terminated in the two terminals marked AC. Before turning ON the mains power, ensure you have the battery connected to the control panel, then insert the fuse into the terminal block using the holder provided.
Power Up correct; and check voltage at the far end. Disconnect furthest item on Keybus and work back measuring voltage. The panel will provide around 550mA of current for powering modules and detection devices. Always keep this in mind when expanding a system. If you need more power, you should use a PC5204 module. This will provide an extra 1.0Amp of power. You may be using some additional modules with the Power832. Always repower the control panel after adding them onto the system.
Power Up Ready Armed Trouble If the keypad is showing the orange “Trouble” LED, there is a problem with the panel. To find more detail on the problem, press [*][2]. The default Master Code is [1234] and the default engineer code is [5015].
Power Up Common Start-Up Problems Loss of Clock – Panel needs to have time and date set. To do this press [*][6][Master Code][1], then enter time/date as: HH:MM/MM/DD/YY. TLM – Panel has no phone line connected. To cure this fault, enter programming [*][8][Engineer Code] and enter section 015. Turn off option 7. Zone Fault/Tamper – Incorrect zone supervision selected. Enter programming [*][8][Engineer Code] and enter section 013. Select correct options from 1 and 2.
Features [*] Commands The Power832 allows for the access of information and outputs by using [*] commands. These commands are very similar on all DSC products. [*][1] Zone Bypass Features Enter [*][1]. Bypass light flash. Enter two-digit zone number to bypass. Zone light ON; push [#] key. [*][2] Display Troubles Press [*][2] to view trouble conditions. Keypad will flash trouble light and LED keypad zone light(s) to indicate troubles. See Installation Manual, page 13 for detailed explanation.
Features Power832 Expansion Flowchart 16 Features Power832 Expansion Flowchart
Features Power832 Expansion Flowchart Power832 Expansion Flowchart 17
[*] Commands [*][5] Programming Access Codes Press [*][5][Master Code]. The keypad will flash the program light and turn on the zone light for any codes already programmed. Enter the two-digit user number for the code you want to program. The corresponding zone light will flash. Enter the four-digit code. The zone light will then turn on steady. Do not use [*] or [#] in user codes. Push the [#] when you have finished. To assign codes to partitions, press [*][5][Master code][9].
[*] Commands [*][7] Output Functions [*][7][Access Code] to activate Utility Output. [*][7][2] to activate smoke detector or shock sensor reset. [*][8] Access to Engineering Functions Press [*][8][Engineer Code] to enter engineering functions (Installation Manual, page 19). [*][9] Arming without Entry Delay Press [*][9][Access Code] the panel will remove the entry delay from the partition. [*][0] Quick Arm/Quick Exit Press [*][0] to quick arm the system.
Features Clearing Troubles If the orange “Trouble” LED is lit, there is trouble on the system. To view, press [*][2]. The trouble condition will be displayed on the LCD keypad. Scroll through the display using the [<][>] keys to see if more than one trouble condition is present. On the LED keypads, the trouble condition will be indicated by a lit LED zone. NOTE: Zone 1 LED gives a further sub-menu of troubles. Therefore, if [1] is lit, push [1] again for specific information on the trouble condition.
Clearing Troubles [4] Failure to Communicate Panel unable to send information to central station. Check telephone line, telephone number of Central Station, format and reporting codes. Dial number from handset and listen for tones to ensure number correct. [5] Zone Fault The trouble will be indicated if any zone on the system is in a trouble condition, i.e. if it could not send an alarm to the panel if required to do so. Press [5] to view the zone number.
[*] Commands [1] Further Sub-Menu of Troubles If [1] comes ON, push [1] again for specific trouble present. LED lit after pushing [1] again will indicate type of trouble. [1] Low Battery Check Battery. May be ON if battery is below 11.5 volts. [2] Bell Circuit Trouble Panel senses open condition on bell circuit. [3] General System Troubles Only generated if PC5204 or PC5400 have fault conditions. [4] General System Tamper Tamper on module.
Features Module Guide The following modules can be used with the PC5015. Keypads (Max. of 8 per system) PC5508TZ – 8 Zone LED keypad PC5532TZ – 32 Zone LED keypad LCD5500TZ– LCD keypad Zone Expansion (Max. of 3 per system) PC5108 – 8 zone expander module Output Modules (Max. of 1 of each per system) PC5208 PC5204 – 8 low current outputs (50mA) – 4 high current outputs (1A) Home Automation Control (Max. 1 per system) Escort5580 – Escort module TW7223 – X-10 control unit Device Control (Max.
Features Default Settings 001 Zone Definitions Zone 1 01 Entry/Exit Zone 2 25 Instant Zone 3 03 Instant Zone 4 03 Instant Zone 5 03 Interior Zone 6 03 interior Zone 7 03 Interior Zone 8 05 Interior 005 System Times Entry Delay 1 030 Seconds Entry Delay 2 045 Seconds Exit Delay 030 Seconds Bell Cut-Off 020 Minutes 006 Engineer Code Default 5555 007 Master Code Default 1234 013 First System Option Codes Double End Of Line Resistors 164 Bell Delay Default 24 000 Minutes
Features Basic Programming Now let’s look at how to change some of the default settings listed on the previous page. If you are using the Power832 as a “bells only” system, this could be the only programming you need to do. For example, let’s look at changing the entry delay from default 30 seconds to 45 seconds. Entry delay is in section 005, “System Times”, on page 4 of the Programming Worksheets. All entries in section 005 require 3 digits.
Basic Programming Once you press [#] to exit section 005, the keypad will again display “Enter Section” followed by three dashes. If you want to make changes to another section, then enter that new section number. If you want to exit engineering mode, simply press [#] once more and the keypad will revert to normal mode. Let’s look at changing the default setting of single end of line resistors to our recommended double end of line resistors.
Basic Programming To toggle options “ON” or “OFF” press the corresponding number on the keypad. Press [2] and the dash is replaced by the number, indicating the option is now “ON”. Press [2] again and the number is replaced with a dash, indicating the option is now “OFF”. Go through each of the options in the section and determine if the option should be “ON” or “OFF”. Once all the options are selected correctly, press the [#] key. The keypad again displays “Enter Section” followed by the three dashes.
Basic Programming Programming Examples: Using a LCD keypad 28 Basic Programming
Features Translation The Language Barrier (01) Delay 1 = Final Exit 1 (02) Delay 2 = Final Exit 2 (03) Instant = Normal Zone (05) Interior Stay/Away = (Part Set) Zone will be omitted if no Final exit zone is activated. Zone arms if final exit activated. (06) Delay Stay/Away zone = Always gives entry delay. (25) Interior Delay = Entry Route/ Walk Through for domestic installations. Use for Hall PIR. In the Stay Armed mode, this zone will give entry delay when activated.
Features Using the Big Books How to use the Installation Manual and Programming Worksheets included with this panel: The Programming Worksheets and Installation Manual that accompany the Power832 may appear daunting to the first time user.
Using the Big Books Section 2 refers to wiring the control panel, including a description of the main panel terminal strip, the connection and operation of the Keybus, current ratings of modules, module supervision and zone wiring. Section 3 is a summary of all the user keypad commands including arming, disarming, auto bypass and all the keypad commands. Also included is a description of the operation of the function keys and partition and global keypads.
Using the Big Books For example, you may not be sure what “TLM Enable” means in programming section 15. Beside the option number is a reference number (in this case 5.11). If you open the Installation Manual at section 5.11 (page 32), you will see that TLM stands for Telephone Line Monitoring. There are several options that require programming for the telephone line monitor feature. These are summarised at the end of the description and include which section the option can be programmed in.
Features Technical Support: 01482 322228/329911 33
Unit C51 Winfrith Technology Centre Winfrith Newburgh Dorchester DT2 8DH Telephone 01305 851700 Fax 01305 851660 Email: Sales@dscuk.co.uk Web-Site: www.dscuk.co.
