- DSC, a Tyco International Company Home Security System User Manual

ManualsBrandsDSC ManualsHome Safety ProductPOWERSERIES PC1616

PC1616/PC1832/PC1864 STANDARD INSTALLATION GUIDE

This Installation Guide provides the basic installation, wiring and programming information required to program the PowerSeries PC1616,

PC1832 and PC1864 control panels. This guide shall be used in conjunction with the PowerSeries PC1616/1832/1864 Reference Manual

which can be obtained from your local dealer or downloaded from the DSC web site at www.dsc.com.

NOTE: All necessary information required to meet UL Listing requirements is contained in this document.

Read the complete guide, then work through each step as indicated.

FEATURES

PC1616 PC1832 PC1864

OUT Of THE BOX

On-board Zones 6 8 8

Qty 1 

Qty 2 

Qty 1 

Qty 4 

Qty 16 

Qty 1 

Cabinet

PC Module

Installation guide

User manual

Cabinet Label

Cabinet Door Plug

Standoffs

5.6KΩ Resistors

2.2KΩ Resistors

1.0KΩ Resistors

10Ω Resistors

Grounding Kit

Hardwired Zones 16 (1xPC5108) 32(3xPC5108) 64 (7xPC5108)

Wireless Zones 16 32 32

Keypad Zone Support



On-board PGM Outputs PGM 1 - 50mA

PGM 2 - 300mA

PGM 1 - 50mA

PGM 2 - 300mA

PGM 1, 3, 4 - 50mA

PGM 2 - 300mA

PGM Expansion 8x50mA (PC5208)

4x500 mA (PC5204)

8x50mA (PC5208)

4x500 mA (PC5204)

8x50mA (PC5208)

4x500 mA (PC5204)

Keypads 8 8 8

Partitions 2 4 8

SPECIFICATIONS

Temp Range ....... 0°C-49°C (32°F-120°F)

Humidity (Max)........................... 93%R.H.

Power Supply........ 16.5VAC/40VA @60Hz

Current Draw (Panel) .........110mA (nom.)

Aux+ Output............11.1-12.6V

DC/700mA

Bell Output..............11.1-12.6VDC/700mA

User Codes 32 + Master Codes 32 + Master Codes 32 + Master Codes

Event Buffer 500 Events 500 Events 500 Events

Transformer Required 16.5V

AC/40VA 16.5VAC/40VA 16.5VAC/40VA

Battery Required 4Ah / 7Ah/14AHr 4Ah / 7Ah/14AHr 4Ah / 7Ah/14AHr

Bell Output 12V/700 mA (cont) 12V/700 mA (cont) 12V/700 mA (cont)

COMPATIBLE DEVICES

Keypads (

Backward compatible with all PowerSeries keypads) Modules

PK5500 Keypad...........................................................125mA (max.)

PK5501 Keypad...........................................................125mA (max.)

PK5508 LED Keypad...................................................125mA (max.)

PK5516 LED Keypad...................................................125mA (max.)

PC5532Z LED Keypad ................................................125mA (max.)

LCD5511 Fixed Message LCD Keypad........................ 85mA (max.)

LED5511Z 8-zone LED Keypad .................................100mA (max.)

Cabinets

PC5003C .....................................222x298x78mm (11.3x11.7x3.0in)

PC500C .........................................213x235x78mm (8.4x9.25x3.0in)

Refer to the Reference Manual for alternate control cabinets

T-Link TL-250/TL300 .......................................................275/350mA

PC5100 2-wire Interface ............ 40mA plus devices to 170mA max.

PC5132-433 Wireless Receiver .............................................125mA

RF5108-433 Wireless Receiver .............................................125mA

PC5108 Zone Expander ..........................................................30mA

PC5204 Power Supply with 4 Programmable Outputs ............30mA

PC5208 Low Current Programmable Output Module ..............50mA

PC5400 Printer/DVAC Module .................................................65mA

PC5401 Bi-Directional RS232 Module (Not UL Listed) ............65mA

Escort5580 Telephone Interface Module ...............................130mA

Refer to the Reference Manual for additional devices.

Classified in Accordance with ANSI/SIA CP-01-2000 (SIA-FAR)

29007109R003

Summary of content (16 pages)

PAGE 1
PC1616/PC1832/PC1864 STANDARD INSTALLATION GUIDE This Installation Guide provides the basic installation, wiring and programming information required to program the PowerSeries PC1616, PC1832 and PC1864 control panels. This guide shall be used in conjunction with the PowerSeries PC1616/1832/1864 Reference Manual which can be obtained from your local dealer or downloaded from the DSC web site at www.dsc.com.
PAGE 2
Hardware Installation Begin the installation by mounting the cabinet in a dry protected area with access to unswitched AC power. Install Hardware in the sequence indicated below. Do NOT apply power until installation is complete. NOTE: All wiring entry points are designated by arrows. All circuits are classified UL power limited except for the battery leads. Minimum 1/4” (6.4mm) separation must be maintained at all points between power limited and non-power limited wiring and connections. 1.
PAGE 3
Hardware Installation (Cont.) North America Only POWER LIMITED Stand Off PC Board Cable Tie (not supplied) recommended Cabinet 2. Position circuit board mounting holes over standoffs. Press firmly on board to snap-in-place. DSC UA503 Primary:120VAC/60Hz. Secondary: 16.5VDC 40VA DSCPTD 1640U Class II Transformer 220 1. Insert Stand off into cabinet mounting hole in the desired location. Snap-inplace.
PAGE 4
Hardware Installation (Cont.) 4. AUX Power Wiring The control panel can provide a maximum of 700mA of current for modules, powered detectors, relays, LED’s etc.… If the total current required exceeds 700mA an additional power supply is required (e.g.,PC5200, PC5204). See list below. NOTE: Min/max operating voltages for devices, sensors and modules is 9.5VDC - 14VDC Refer to the list of Compatible Devices on the first page for the current draw of individual devices 5.
PAGE 5
TESTING & TROUBLESHOOTING Testing: • • Power up system Program options as required (See Programming Section on reverse side) Note: For advanced programming refer to the PC1616/1832/1864 Reference manual • • Violate, then restore zones Verify correct Reporting Codes are sent to the Central Station Troubleshooting: LCD5500 LCD Programmable-Message Keypad • • • Press [✱][2] to view a trouble condition. The trouble light will flash and the LCD will display the first trouble condition present.
PAGE 6
Trouble Cause Trouble [1] Service Required Press [1] to determine specific trouble [1] Low Battery Main panel battery less than 11 VDC NOTE: This trouble condition will not clear until the battery voltage is 12.5VDC min., under load. [2] Bell Circuit Bell+, Bell-...Open Circuit Troubleshooting NOTE: If battery is new allow 1 Hr. for battery to charge. • Verify voltage measured across AC terminals is 16-18 VAC. Replace transformer if required.
PAGE 7
Trouble Cause Troubleshooting No AC at panel AC input terminals Verify voltage measured across AC terminals is 16-18VAC. Replace transformer if required. Phone Line Voltage at TIP, RING on main panel less than 3VDC • Trouble [2] AC Failure Trouble [3] Telephone Line Trouble • Measure the voltage across TIP and RING on the panel: • No phone off-hook – 50VDC (approx) • Any phone off-hook – 5VDC (approx) Wire incoming line directly to TIP and RING.
PAGE 8
Trouble Cause Troubleshooting One or more wireless devices have not checked in within the programmed time • Trouble [5] Zone Fault (Cont.
PAGE 9
PROGRAMMING How to Program: DSC recommends filling in the Programming Worksheet with the required programming information before programming the system. This will reduce the time required to program and will help eliminate errors. To enter Installer Programming press [*][8][5555]. The Program light will FLASH (or in the case of the programmable LCD keypad the display will change to ‘Enter Section’). An error tone indicates the installer code entered is not correct.
PAGE 10
[402] Downloading Computer Phone Number (32-digits) I DII___II___II___II___II___II___II___II___II___II___II___II___II___II___II___I I___II___II___II___II___II___II___II___II___II___II___II___II___II___II___II___I [403] Downloading Access Code Enter 4 or 6-digit code This code identifies the downloading computer to the panel. The downloading access code prevents unauthorized access to the panel.
PAGE 11
[013] – First System Option Code [005] System Times This section programs the entry and exit delays for the control panel. After entering section [005] press [1] to select partition 1. Enter the 3-digit delay time for Delay 1 type zones, Delay 2 type zones followed by the exit delay time. Press [#] to exit the sub-menu and return to regular programming. NOTE: For SIA FAR Installations, the Exit Delay must be within the range of 045-255 seconds (Default 60 seconds).
PAGE 12
[310]-[311] Partition Identifier Codes Enter a 6 digit Maintenance Code [380] – First Communicator Option Codes Opt [310 System Acct. Code I___II___II___II___II___II___I [311] Partition 1 Acct. Code I___II___II___II___I 1 [350] – Communicator Format Options This section determines the communication format used for central station reporting.
PAGE 13
LISTING REQUIREMENTS UL Listed Commercial and Residential Installations The installation requirements listed below must be met for the following grades of service. Grade AA Central Station and Police Connect (Standard or Encrypted Line Security Service) The installation must use T-Link module which communicates over LAN/WAN to the Sur-Gard MLR-IP receiver or the TL200/250 which communicates over LAN/ WAN/Internet to the SG System III receiver. Polling time must be 90 seconds.
PAGE 14
PC1616/PC1832/PC1864 Installer Programming Quick Reference Chart SIA False Alarm Reduction SIA Feature Programming Section Comments Range/Default Requirement Exit Time [005], 3rd entry Access to Entry and Exit delays for each partition and Bell Time Out for the system For Full or auto arming: Range:45- 255 seconds Default: 60 sec.
PAGE 15
Note to Installers Limited Warranty This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring each item in this warning to the attention of the users of this system. Digital Security Controls warrants the original purchaser that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use.
PAGE 16
FCC COMPLIANCE STATEMENT CAUTION: Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.