User Manual RoboGeek 21T (R3760)
Table of Contents 01 Important Safety Information Use Restrictions Battery and Charging 04 Product Diagram Robot Accessories Charging Dock Remote Control 09 Operating and Programming Notes Before Cleaning Quick Start How Robot Clean Your Home Cleaning Schedule Use Your Robot Cleaner with “dserlife” App 23 Regular Robot Care Emptying Robot’s Bin Cleaning Robot’s Filter Cleaning Robot’s Side Brush Cleaning Robot’s Cliff Sensors and Charging Contacts Cleaning Robot’s Floor Tracking Sensor Cleaning Robot
Important Safety Information This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Your robot is not a toy. Do not sit or stand on this device. Small children and pets should be supervised when your robot is operating. Store and operate your robot in room temperature environments only. Do not use this device to pick up anything that is burning or smoking. Do not use this device to pick up spills of bleach, paint, or other chemicals, or anything wet. If the room to be cleaned contains a balcony, a physical barrier should be used to prevent access to the balcony and ensure safe operation.
Your robot’s Charging Dock may be protected with a surge protector in the event of severe electrical storms. Never handle the Charging Dock with wet hands. Always disconnect your robot from the Charging Dock before cleaning or maintaining it. Please ensure voltage rating for enclosed Charging Dock matches standard outlet voltage. Used battery packs should be placed in a sealed plastic bag and disposed of safely according to local environmental regulations.
Product Diagram Robot WiFi Indicator Indicator flashes blue quickly: the product enters the reset WIFI connection mode Indicator flashes blue slowly: the product has paired with phone, please input WiFi name and password in App Indicator blue long bright: The product has been successfully connected to the mobile App. Power Button Long press to turn on / off the robot, short press to pause and continue to work.
Anti-Collision Sensors Anti-Drop Sensors Charging Contacts Universal Wheel Side Brushes Battery Pack Driving Wheels Power Switch Main Brush Dust Bin 05
Accessories 1 x Charging Dock 1 x Adapter 1 x Remote Control (with 2 x AAA battery) 1 x Dust Bin 4 x Side Brushes 1 x Sponge Filter and High Efficiency Filter 1 x Brush Cable Ties (x5) 06
Charging Dock Charging indicator Location for remote control Signal transmission area Butting charging pole piece 07
Remote Control Mode and time display screen Automatic re-charging button Automatic cleaning Direction buttons Start / Pause button Clock setup button Scheduling button Spot cleaning button Edge cleaning button Small-space button Max vacuuming cleaning button 08
Operating and Programming Notes Before Cleaning Before using Robot, pick up objects like clothing, loose papers, pull cords for blinds or curtains, power cords, and any fragile objects. If the Robot passes over a power cord and drags it, there is a chance an object could be pulled off a table or shelf. If the room to be cleaned contains a balcony, a physical barrier should be used to prevent access to the balcony and ensure safe operation.
Quick Start 1. Plug in the Charging Dock and place the remaining wire into the trunking at the bottom of the Charging Dock Failure to place the remaining wire into the trunking, may cause Robot to become stuck while charging or cleaning. 4. Install Side Brushes Attach Side Brushes to the bottom of Robot by pressing a brush into each slot until it clicks. 5.
6. Start Cleaning Cycle Press the 7. Pause power button once to wake up the robot. To pause the robot during a cleaning cycle press the button on robot or press the button on the Remote Control. Press the power button again to start a cleaning cycle (or button on Remote Control). To resume the cleaning cycle, press button again. To send robot back to the Charging Dock, press the Remote Control. If its battery gets low before finishing a cleaning cycle, robot returns to the Charging Dock to recharge.
How Robot Clean Your Home Robot continues this process until it has cleaned an entire level of your home. If its battery gets low before finishing a cleaning cycle, Robot returns to the Charging Dock to recharge. 1. Auto Cleaning At the start of a cleaning cycle, Robot will clean your home efficiently. At various times throughout the cleaning cycle, Robot touches up around the edges of the room, as well as chair legs and other furniture.
Cleaning Preferences 5. Edge Cleaning After robot finishes cleaning the open areas of your floor, it uses Edge Clean to ensure that it has cleaned along walls and around furniture legs. If you prefer a quicker edge cleaning, press the button on Remote Control. 3. Spot Cleaning When you select Spot Cleaning, robot intensely cleans a localized area by spiraling outward about 3 feet (1 meter) in diameter and then spiraling inward to where it started.
7. Manual Cleaning You can direct Robot to clean a particular area by using the directional buttons on the remote control.
Cleaning Schedule The cleaner has cleaning schedule settings which allow you to customize when Robot cleans your home. These settings are available only through the Remote Control. Note: Please make sure the Remote Control near by the Robot while setting the Clock or Schedule. 1. Set the Remote Control’s Clock Press button on Remote Control, and then the hour section begins to flash in the clock display setting window. Press or button to select the desired figures.
2. Setting Cleaning Schedule Press button on Remote Control, and then the hour section begins to flash in the Cleaning Schedule display setting window. Press or button to select the desired figures. Press the or button to select the minute or hour section. 3. Cancel the Cleaning Schedule Press and hold button approximately 4 seconds on Remote Control, the Robot will “BEEP” when the Cleaning Schedule process cancel completed.
Use Your Robot Cleaner with “dserlife” App 1.
2. Register / Login an Account(ie. iOS App) Open the App and register an account and log in.
3.
4. Turn on Your Robot Cleaner a. Press the Power Switch Button at the bottom of the robot cleaner. b. Long press the Power Button and auto-charging button on the top of the robot together, the WiFi indicator will flash. Then you can connect device with your phone. 5. WiFi Connection Before you start, make sure that: 1. Your smartphone or tablet is connected to a 2.4Ghz WiFi network.(This robot only support 2.4Ghz network.) 2. Your smartphone or tablet is running iOS 8.0 (or above) or Android 4.
6.
Device Info Information about the device name and details Other 1. Share Device: add an another App account to control this device 2. Accessories: to remind you to replace your old accessories in time 3. Schedule: set a time to auto cleaning 4. Check Firmware: Information about WiFi current version and MCU current version Restore Factory Setting * You can connect Amazon's ALEXA and Google Assistant amazon's ALEXA and Google Assistant as App instructions.
Regular Robot Care To keep robot running at peak performance, perform the following care procedures. If you notice robot picking up less debris from your floor, then empty the bin, clean the filter and clean the extractors.
Emptying Robot’s Bin Cleaning Robot’s Filter 1. 1. Remove filter by grasping the white tab. 2. Shake off debris by tapping the filter against your trash container. Press bin release button to remove bin.
Cleaning Robot’s Side Brush 1. Remove the brush 2. Clean the brush and the brush post, and reinstall the brush. 2. Cleaning Robot’s Cliff Sensors and Charging Contacts 1. Wipe Robot’s Cliff Sensors with a clean, dry cloth. 25 Wipe the charging contacts on Robot and the Charging Base with a clean, dry cloth.
Cleaning Robot’s Floor Tracking Sensor 3. Clean the rolling brush with the provided cleaning tool or a vacuum cleaner. 4. Reinstall the rolling brush by inserting the fixed protruding end first and then clicking into place. 5. Press down to snap the brush guard into place. Use a clean, dry microfiber or soft cotton cloth to wipe any debris that has accumulated in the round sensor opening on the right side of the bottom surface. Do not spray cleaning solution directly into the sensor opening. 4.
Battery and Charging Information Remove the extractors. Remove any hair or debris that has collected underneath the caps and around the axles. Lithium Ion Battery Important: Lithium ion batteries and products that contain lithium ion batteries are subject to stringent transportation regulations.
Battery Removal 2. Reinstall the battery with the battery label and tabs facing up. 3. Reinstall the battery door and the two screws. Take care not to pinch the side brush in the battery door when re-installing the battery. Follow these instructions to remove and reinstall robot’s battery: 1. Unscrew the door and the two screws on the battery door, then remove.
Troubleshooting Robot will tell you something is wrong with a two-tone distress sound followed by message. The indicator will also blink or lit red. Refer to the chart as below to resolve Robot’s problem. If the problem is not resolved, please contact our COST FREE customer service team for more assistance. Rebooting Instructions For some errors, rebooting Robot may resolve the problem.
Indicator Flashing Red Robot Blinks and Says What to Do Robot is stuck and one of the wheels is not making contact with the floor(hanging in mid-air). Robot may be in an extremely large room and the bumper is not registering obstacles. Restart cleaning in a new location. Two beeps Robot is stuck. If Robot is stuck, free it and start in a new location. Clean Robot’s side wheels of hair and debris. Push the wheels in and out, and check that they both turn freely.
Frequently asked questions Problems cannot be activated. Solutions Make sure the main power switch is in the ON position. Make sure the battery is fully charged. Replace the batteries (2 AAA) in the remote control. Make sure the remote control is within range (16 ft/5 m) of Robot. If you still have trouble, turn off the main power switch and then turn it back on. The remote control does not work. Replace the batteries in the remote control. Make sure Robot is turned on and fully charged.
Problems Solutions Robot cannot return to the Charging Base. Remove objects within 3 ft/1 m to the left and right side and within 6 ft/2 m of the front of the Charging Base. When Robot is in the vicinity of the Charging Base, it will return more quickly. However, if the Charging Base is located far away, Robot will need more time to return. Please be patient as it works its way back. Clean the charging contact pins. The rolling brush does not rotate. Clean the rolling brush.
Use the Boundary Strip With the Boundary Strip, you can keep Robo away from any area or item you do not want Robo to clean. the cleaner will recognize the Boundary Strip and will not cross into the blocked-off area. 1. Identify the area or item you do not want the cleaner to get close to. 2. If necessary, use scissors to cut the Boundary Strip to a shorter length. Be sure to correctly measure the length before cutting.
For FAQs and more information, please visit www.dserlife.com. E-mail: support@dserlife.
