Specifications

DSX-1040PDP
Power Distribution Panel
DSX Access Systems, Inc. 10731 Rockwall Road Dallas, Texas 75238 / 888-419-8353 / 214-553-6140 / www.dsxinc.com
11/2012
 12VDC / 6A Power for Controllers
 Battery Backup for Controllers
 Optional Battery Backup for Locks
 Lock Power 12VDC-8A/24VDC-4A-8A
 UL 294 / UL 1076
 AC Loss/Low Battery Supervisory Outputs

All Outputs - Class II, Power Limited

Fire Override Input & Output
General Information
The DSX-1040PDP Power Distribution Panel is the supervised
power plant for the DSX-1048PKG Intelligent Controller. The
DSX-1040PDP houses the panel and lock power supplies, and
backup batteries. The DSX-1040PDP is comprised of a DSX-
1040PE enclosure, an SWS-150 15VDC power supply for the
controllers, an SWS-150-[15] or [27] for either 12 or 24VDC
locks, and a DSX-1040PDM Power Distribution Module. The
DSX-1040PDP carries a Limited 2 Year Warranty.
Power Architecture
The DSX-1040PDP contains an SWS-150 Power Supply that
converts 115VAC to 15VDC for Controller Power. Also
present is an SWS-150 15/27 Power Supply which converts
115VAC to either 12 or 24VDC for Lock Power. Both Power
Supplies feed power to the DSX-1040PDM Power
Distribution Module. The DSX-1040PDM provides fused
12VDC/6A power to the DSX-1040CDM located in the DSX-
1048 enclosure. The DSX-1040CDM redistributes the power
through individually fused outputs to each Controller in the
DSX-1048. The Controllers have 12VDC/1A fused power
outputs for Card Readers and Keypads.
Power Distribution Module
The DSX-1040PDM performs several critical functions. First,
it takes the 15VDC power from the SWS-150 and provides
two 12VDC 3 amp, Class II, Power Limited, Fused Outputs to
power the DSX-1040CDM which distributes the power to the
DSX-1042 Controllers in the DSX-1048PKG. It provides a
12VDC Battery Charging Circuit to charge backup batteries
for the Controllers. It also provides a charging circuit for the
optional batteries used to backup the 12 or 24 volt lock power
from the SWS-150 power supply. The Power Distribution
Module has outputs to signal Loss of AC and Low Battery.
The module also has a Battery Test Input and Load Shed
capabilities. The DSX-1040PDM routes Lock Power through
individual fuses for each of the 8 outputs. All Outputs are
Class II, Power Limited.
Inputs
The DSX-1040PDM has a Battery Test Input. This Input when
activated shuts off the charging circuit and load tests the
battery for 1minute. This Input can be tied to a spare Output in
the DSX-1048PKG Controller and programmed by Time Zone
to occur when desired. The module also has connection points
for a Lock Power Fire Override Relay to break Lock Power to
all 8 Outputs.
Outputs
The DSX-1040PDM Power Distribution Module has 3
normally closed Relay Outputs, two to signal Loss of AC (one
for panel power and one for lock power) and one to signal
Low Battery. These Outputs can be connected to three spare
Inputs in the DSX-1048PKG. The DSX-1040PDM routes
Lock Power through individual fuses for each of the 8 Outputs
with connection points for the lock wiring and for the
Output relays located in the DSX-1048. There is also an output
from the Lock Power Fire Override that can be connected to an
input in the 1048 or can be used to connect to the Fire
Override Input on the next 1048 and 1040PDP.
Diagnostic, Supervisory and Status LEDs
The DSX-1040PDP has 17 diagnostic LEDs for power and
blown fuse indication. There are Power On LEDs for each of
the two power inputs, LEDs for Low Battery and Battery Test,
and for AC Loss, and Fire Override. The DSX-1040PDM also
has 1 LED for each of the eight fused Outputs for Lock Power.