User Manual
Safety Caution
ӄǃ֯⭘䈤᰾ӻ㓽
Power interface: 1 hard disk with screen 12V/3A
Lock screen button: turn on/o screen display
USB interface: 1 USB 2.0 interface (support upgrade, and mouse)
Antenna: for wireless signal transmission
Microphone: support microphone voice intercom
Speaker: Audio output
Hard Disk: Support 2.5" 2TB SSD
1
2
3
4
5
6
7
Preview interface
Main menu
Click on the screent and it will pop up menu button“ ”, click
" " to open or close the preview interface channel volume,click " "
zoom button on single screen, enter into the magnication screen to display
it,click " " to enter into the main menu interface, click " " to enter into
the video playback interface,click " " to enter into PTZ control interface.
Step 1: Open WLAN
Step 2: Click "Hotspot list" to select the name of the wireless hotspotyou
want to connect to.
Step 3: Enter the correct password
Step 4: Click "Back" exit to the wireless settings interface to view the wireless
connection status, Indicates successful connection.
Tips: After the network conguration is successful, wait a while (about ten
seconds), and wait until the network icon in the upper right corner change
, this indicates that the device is online (APP can be viewed remotely).
Step 1: The user star the recorder and camera, and the IPC reset enters the
code mode.
Step 2: Enter the code interface, click on the code to match.
Tips:
1). The camera can only perform the pairing in the reset state; the camera
usually presses the reset button to perform the pairing code.
2). If the camera still does not match the code after the code has timed out,
click “Match Code” again to try again.
3). If you need to replace a new camera, please click "X" to delete the channel
and then click on the code to match.
Video playback: Play recorded video
System setup: System related settings (language, time, network settings,
etc.)
Record setup: Set the recording schedule, TF card information and
formatting
Match code: Sdd camera
Alarm setup: Set mobile alarm, APP alarm and other functions
System manage: system information, factory settings, host upgrade, IPC
upgrade, etc.
Add wireless camera
Interface description
NVR interface description
4. Operation instruction
Wireless internet access
Enter the main interface, select system settings, select wireless Internet
access, and make wireless connection settings.
Statement
It is highly appreciated for you buying our products.the main application of
our product will be introduced in this guide.please feel free to contact us if
you have any question,and further information will be found on our WEBSITE
and technical supporting center.we will not give another information about the
inaccurate content in this guide,since the product be updated or changed with
software or hardware.If there is any discrepancy between the product
description and the actual product, the actual product shall prevail.
9
1. In order to make the machine work normally for a long time, the machine
should be placed in a relatively dry and dust-free space.Avoid short circuits
caused by the machine being wet.
2. Check adaptor voltage, prevent damage device since using wrong adaptor.
3. The machine should work at the range of the temperature and humidity
allowed by the technical index.
4. It should be avoid that the machine be set in the vibration environment.
5. Installation of the machine have to comply with local or national standard.
Before leaving factory, the camera has been matched with Wireless NVR
with Touch screen, the image will come out when the kit is powered. If users
need to re-match code, please operate as below˖
QUICK USER GUIDE
IPC
%XWWRQRSHUDWLRQIRU7ZREXWWRQPRGHO
Power Button: Keep pressing for 5-10 seconds to power on/power o
Reset Button: Keep pressing for 5-10 seconds to reset
Solid in Blue: Wi-Fi connected, camera running normally
Blink Slowly in Blue: Firmware update
The instructions of LED light :
Blink Slowly in Red: Awaiting Wi-Fi connection, ready for adding devices
Blink Fast in Red: Wi-Fi connecting
Solid in Red: Network problem
Mini NVR can be combined with dierent cameras to form a kit.
The interface description below only takes common cameras as an example. Please
refer to the actual interface position of the camera in the package.
%DWWHU\FDPHUDNLWZLWKWRXFKDEOHPRQLWRUPDQXDO
Camera Lens
PIR Sensor
LED Indicator
IR Lamp
Microphone
Speaker
SD Card Slot
USB Port
Charging Status
Reset Hole
Power Button
White Light
Antenna
Mic-phone
USB interface
Power supply
HDD cover
lock screen button
CONNECT TO ROUTER
HDMI
trumpet
Company: SHENZHEN DC Times Technology CO.,LTD
Address: Floor 3, Building J, Jinchangda, No. 2000089, Shangwei industrial zone ,
Zhangkengjing community,Guanhu Town,Longhua New District,Shenzhen,
Guangdong Province, China
Model: NVR-0704mt
Product name: Net Video Recorder
RF Exposure Warning Statements:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment shall be installed and operated with
minimum distance 20cm between the radiator & body.