Smart watch USER MANUAL Thank you for choosing our smartwatch. By reading this manual, you can fully understand the use and operation of the device. Any questions, please contact our support services team. Included in the box: a box, a manual, a watch and a data cable. Binding and unbinding the smartwatch: 1. App Download 1.1 Scan the Q R code below to download the app. 1.
After WearPro is installed, the app icon appears as . 2. Bind the smartwatch with WearPro 2.1 Search the bluetooth name to connect/pair Swipe down on the main interface of the watch, find the first icon and click it, and remember the Bluetooth name of the watch; then open the app "WearPro" on your phone, click the "Device" on the bottom bar, find and click "Search for bound devices" to start the search in the Bluetooth list, find your watch's Bluetooth name and pair it.
After the watch is successfully bound to the application, the data in the smartwatch can be synchronized to the application. 5. Find the smartwatch After the watch is successfully bound to the app, click "Find Watch" in "WearPro", and the watch screen will light up and vibrate. 6. Camera Click “camera” in the app WearPro to wake up the camera mode of the watch, click the camera button on the watch to take photos, and the photos will be automatically saved to the phone album. 7.
2) When the smartwatch is in the second-level or the third-level interface, short press the button to go back to the dial interface. 3) Long press the button, tap"√" to turn off the smartwatch, tap"×" to go back to the dial interface. Charging description: Magnetic charging shown as the picture below. Smartwatch functions introduction 1.1 Shortcut function 1) Swipe left to find the "+" icon, click the icon to add some functions as a shortcut to them.
Fitness data is turned on by default. When you enter the fitness data interface, scroll up the screen, the smartwatch will display the current data of steps, distance, and calories. The data will be wiped out at 00:00 every day in the morning. 1.4 Heart rate After you wearing the smartwatch correctly, you can measure heart rate when you enter the heart rate function. If you don’t wear the smartwatch properly, it will remind you to wear firmly for the measurement. 1.
Your gender must be set as female to have this feature in WearPro. After the setting of the feature is completed, the data will be synchronized to the watch to view your current physiological period. 2.2 Alarm clock Entering the alarm clock interface can set up to 5 alarm clocks. 2.3 Stopwatch Click the stopwatch to enter the timing interface, and you can record the time once. 2.4 Calculator Simple calculations can be performed on the smartwatch. 2.
Click "√" to start the factory reset, click "X" to cancel the factory reset. 2.7.6 About Here you can see the watch's exclusive QR code, Mac code, firmware version, and other information. Frequently asked questions *Please avoid long-time exposure of the device to extreme temperatures that are too cold or too hot, which may cause permanent damage.
This device was tested for operations. To comply with RF exposure requirements, a minimum separation distance of 0mm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
Shenzhen Xinkeying Technology Co., Ltd I hereby declare that the product Product name: Smart watch Model:DTX Max,DTX Max+,DTX Max Pro+,DTX Max mini,DTX Max Pro Trademark: DTNO.1 HW: V1.0 SW: V1.0.0 (Name of product, type or model, batch or serial number) satisfies all the technical regulations applicable to the product within the scope of Council Directives 2014/53/EU, 2014/35/EU and 2014/30/EU: and declare that the same application has not been lodged with any other notified body. ETSI EN 300 328 V2.2.
MANUFACTURER or AUTHORISED REPRESENTATIVE: Address: Shenzhen Xinkeying Technology Co., Ltd 8/F,Block C,Han's Innovation Building,Xili Road, Nanshan District,Shenzhen,China This declaration is issued under the sole responsibility of the manufacturer and, if applicable, his authorised representative. Point of contact: Company: Shenzhen Xinkeying Technology Co.