Owners manual

ManualsBrandsDU-HA ManualsAutomotive70300 DU-HA Humpstor All In One Storage Unit

Tools Needed:

// Hex Key Wrench 1/8” // Wrench or Socket - 3/8”

// 2 Open-End Wrenches - 1/2” // Wrench or Socket - 7/16”

// Wrench or Socket - 1/2” // Hex Key Wrench 7/32”

// Wrench or Socket - 9/16”

DU-HA Humpstor - Topper

Installation Instructions

DU-HA, Inc. // website: www.du-ha.com // phone: 1.866.306.DUHA (3842) // fax: 1.218.998.4013 // 306 Saint Andrews Street South, Fergus Falls, MN 56537

70300

Latch - Steel Black

Latch 97-50-110-1531

Humpstor Main Body

Humpstor Gun Holder FoamHumpster Gun Rack23

Hinge Rod - Zinc Plated SteelHinge Rod14

Humpstor Foam SealHumpster Foam Seal

Humpstor Gun Holder StiffenerHumpstor Stiffener

.25 Brass thru-sert insert.25 Brass thru-sert insert2

.25 Brass insert.25 Brass insert48

Humpstor LidHumpster Lid19

Stabilizer Foot - 5/16-18 x 3" Full Thread Zinc/Rubber

ubber Foot

310

Nut Flange 5/16-18 Zinc PlatedSerrated Flange Nut

5-16-18

611

Flat Washer 1/4 Zinc PlatedANSI B18.22.1 - 1/4 -

Regular - Type B

412

Washer Split Lock 1/4 Zinc PlatedASME B18.21.1 - 1/4

413

Flat Washer #10 Stainless Steel

93852A101417

Lock Nut Nylon Insert #10-24 Stainless Steel90631A011218

Humpstor Bracket Folded Right

119

Humpstor Bracket Folded Left

120

Bracket Top PlateTop Plate521

Bracket O

ffset PlateOffset Plate222

Velcro StrapVelcroe Strap

423

Flat Washer 5/16 Zinc PlatedASTM F436 - 5/16

1824

Lock Nut Nylon Insert 5/16-18 Zinc Plated

95615A1601025

Hex Bolt 1/4-20 x 5/8" Zinc PlatedANSI B18.2.1 - 1/4-20

UNC - 0.625

426

Humpstor Lid Latch Protector PlateLatch Protector Plate327

Rivet - Latch Protector - 5/32 x .040-.118PR52AAPAB328

Round Head Square Neck BoltANSI B18.5 - 5/16-18 UNC

- 0.75

1029

Coupling Nut 5/16-18 x 7/8" Zinc Plated

90264A445330

Hex Bolt 5/16-18 x 2" Zinc PlatedHex Bolt 5-16 x 2331

Hex Bolt 5/16-18 x 3/4" Zinc PlatedANSI/ASME B18.2.1 -

5/16-18 UNC - 0.75

233

Helical Spring Lock WashersANSI B18.21.1 - 0.3125

Wdmt - Humpstor Center Support-4

1001034135

Toyota / Nissan Bed Rail Nut

1001029336

Hex Bolt - UNC (Regular Thread - Inch)ANSI/ASME B18.2.1 -

5/16-18 UNC - 1

337

SierraPacif

ic-29BK

138

Hexagon Socket Button Head Cap ScrewANSI B18.3 - No. 10-32 - 1

239

Hex Bolt - UNC (Regular Thread - Inch)ANSI/ASME B18.2.1 -

5/16-18 UNC - 0.75

143

Topper Clamp - Humpstor

344

Humpstor Handle - Black DU-HA Humptster Handle145

91900A249246

Humpster Brace147

STEP 1 - Attach Handle

Place Handle (B) over holes in Lid Top. Insert two Bolts #10 x 1.5

(M) through Handle (B) and Humpstor (A) Lid. Secure with Flat

Washer - #10 (N) and Lock Nut #10 (O) Use 1/8” Hex Key Wrench.

Note: Handle may already be installed.

STEP 2 - Attach Stabilizer Foot

Install Stabilizer Foot

Attach one Stabilizer Foot (K) to the Left (E), Right (F) and Center

Support (AB) Brackets by threading one Flange Nut - 5/16” (P)

onto Stabilizer Foot (K) shaft and insert through the lower hole of

each Bracket (E,F and AB). Thread a second Flange Nut (P) onto

Stabilizer Foot (K) shaft sandwiching the Bracket in between.

Hint: Flanged side of nuts should face Bracket.

Note: Finger tighten.

Extended Stabilizer Foot

Some installations require a longer Stabilizer Foot (K) (Toyota

Tundra for example). In such cases, prior to installing the

Stabilizer Foot (K), attach one Hex bolt - 5/16” x 2” (U) and

Coupling Nut - 5/16” (X) to each Stabilizer Foot (K).

Installation Instructions:

F (shown)

E (opposite)

F (opposite)

E (Shown)

AB (center support)

Summary of content (5 pages)

PAGE 1
70300 Installation Instructions DU-HA Humpstor - Topper Tools Needed: // // // // Hex Key Wrench 1/8” // Wrench or Socket - 3/8” 2 Open-End Wrenches - 1/2” // Wrench or Socket - 7/16” Wrench or Socket - 1/2” // Hex Key Wrench 7/32” Wrench or Socket - 9/16” Installation Instructions: M B STEP 1 - Attach Handle Place Handle (B) over holes in Lid Top. Insert two Bolts #10 x 1.5 (M) through Handle (B) and Humpstor (A) Lid.
PAGE 2
Page 2 - Continued . . . STEP 3 - Assemble Brackets Option I - Topper Use this option for most standard installations for truck beds with toppers. No additional Drop Down Plates (H) or Off-set Plates (I) are needed. Use the standard Right (F) / Left (E) and Center Support (AB) Brackets.
PAGE 3
Page 3 - Continued . . . STEP 4-Attach Topper Clamps to Truck Look at your bed rail to determine where to attach your topper clamps, find locations where you can attach the clamps at the below spacings and still have room to operate the end latches on the Humpstor. Attach Topper Clamps (G) to truck bed rail by sliding clamps onto truck bed rail on top of the Topper and from the bottom of the rail, slide onto rail as far as possible.
PAGE 4
Page 4 - Continued . . . Humpstor Attachment Place the Humpstor (A) onto the Left (E) and Right (F) Brackets. Thread one Hex Bolt - 1/4” x 5/8” (R), Lock Washer - 1/4” (T) and Flat Washer 1/4” (S) through bottom slots into the threaded holes in the bottom of the Humpstor (two on each end). Note: Center Support Bracket (AB) does not get attached to Humpstor, Humpstor should just be set on the bracket for support.
PAGE 5
Page 5 - Continued . . . Part Description Exploded View / Parts List A B C D E F G H I J K L M N O P Q R S T U V W X Y Z AA AB AC AD L C L J C D M A B D N O E AA I Q W S Z S T V AA 1 1 2 4 1 1 3 3 2 1 3 4 2 2 2 6 3 4 4 4 3 13 10 3 3 3 10 1 3 3 V P Q Qty DU-HA Humpstor Handle Foam Organizer / Gun Holder Plastic Stiffener Bracket Left Bracket Right Topper Clamp Set Drop-Down Plate Offset Plate Center Brace Stabilizer Foot Velcro Straps Bolt - #10x1.