MD200 INSTALLATION/OWNER'S MANUAL AM/FM/CD Marine Receiver Charge Port
MD200 INSTALLATION Preparation Please read entire manual before installation. Before You Start • Disconnect negative battery terminal. Consult a qualified technician for instructions. • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started • Remove 2 transit screws located on top of the unit.
MD200 INSTALLATION Wiring Diagram Rear Preamp Output Connect to amplifier RCA input RCA Cable (sold separately) Antenna Connector BLUE BLACK RED Remote Turn-On Connect to amplifier or power antenna. Insulate wire if not used. AMP Ground Connect to vehicle chassis ground. Accessory Connect to ignition circuit or switched 12 volt source. 5 AMP AGC Fuse YELLOW Memory Connect to battery circuit or constant 12 volt source.
MD200 OPERATION Control Locations 1 2 3 4 5 6 18 17 16 15 7 14 13 12 11 1 Release 10 Preset 6 2 Volume Knob 11 Preset 5 3 Mute / Power 12 Preset 4 / Play / Pause 4 Tune / Track Down 13 Preset 3 / Intro 5 Tune / Track Up 14 Preset 2 / Random 6 Source 15 Preset 1 / Repeat 7 Eject 16 Band 8 USB Charging Port 17 Display 9 Auxiliary Input 18 Audio / Menu 10 8 9 The MD200 has an easy-to-use interface that provides a rewarding experience, as well as support fo
MD200 OPERATION Control Locations - Remote 1 2 3 4 5 9 6 8 7 1 Display 6 Volume Down 2 Volume Up 7 Audio / Menu 3 Power / Mute 8 Band 4 Source 9 Tune / Track Down 5 Tune / Track Up 5
MD200 OPERATION General Operation Faceplate Removal Semi-permanent Faceplate Installation Power On/Off Mode Auxiliary Input Press RELEASE and pull away from the left side to remove. To re-install, insert right side of faceplate first then push left side to secure. Remove trim ring and install supplied #1 x 7/32” Phillips head screw through left side of mounting frame into faceplate. Press to turn the unit on. Inserting a CD will turn the unit on automatically.
MD200 OPERATION General Operation Setup Menu Menu Function Loudness Curve Press and hold AUDIO/MENU for more than 3 seconds to access the setup menu, then press AUDIO/MENU to cycle through menu options. When desired option appears in the display, rotate the volume knob left/right to adjust or activate the desired function. Options Action LOUD OFF Disables the loudness function. Enables the loudness function.
MD200 OPERATION Audio Operation Bass Press AUDIO until BAS appears. Rotate the volume knob left/right to adjust. (-6 minimum / 6 maximum) Treble Press AUDIO until TRE appears. Rotate the volume knob left/right to adjust. (-6 minimum / 6 maximum) Balance Press AUDIO until BAL appears. Rotate the volume knob left/right to adjust. (L12 - R12) "BAL R=L" represents equal balance. Fader Press AUDIO until FAD appears. Rotate the volume knob left/right to adjust.
MD200 OPERATION CD Player Operation Insert CD Eject CD Track Select Fast Forward and Reverse Pause Intro Repeat Random CD-R/CD-RW Compatibility With the label facing up, insert a standard size CD into the CD slot. The CD will automatically begin playback. Press the EJECT button to stop and eject the CD. The unit will change to tuner mode. ll nn to skip to the beginning of the next track. Press TRACK Press TRACK to return to the beginning of the current track.
MD200 OPERATION Limited One Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase. Dual Electronics Corp.
MD200 OPERATION Troubleshooting Problem Cause Action Yellow wire not connected or incorrect voltage Red wire not connected or incorrect voltage Check connections for proper voltage (11~16VDC) Fuse blown Replace fuse Unit will not turn on (no power) Black wire not connected Unit has power (but no sound) Unit blows fuses Excessive skipping Unit will not accept a disc Check connection to ground Speaker wires not connected Check connections at speakers One or more speaker wires touching each oth
Specifications CD Player Frequency response: 20Hz-20kHz Channel separation @ 1kHz: >65dB D/A converter: 1 Bit FM Tuner Tuning range: 87.5MHz-107.