XDVD8285 INSTALLATION/OWNER’S MANUAL DVD Multimedia Receiver with 6.5” Touch Screen Display Safety Notes: The DVD video display of the in-dash unit will not operate while the vehicle is moving. This is a safety feature to prevent driver distraction. In-dash DVD video functions will only operate when vehicle is in Park and the parking brake is engaged. It is illegal in most states for the driver to view video while the vehicle is in motion.
Copyright Notes This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
XDVD8285 PREPARATION Table of Contents Page DVD Region Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warning Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Information/Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preparation/Mounting/Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote Control Overview . . . . . . . . . . . . . .
XDVD8285 PREPARATION WARNING Upon installation of this Monitor/DVD player (“unit”) into a vehicle, the driver of the vehicle must not operate this unit by watching videos or playing video games while driving. Failure to follow this instruction could lead to driver distraction which could result in serious injury or death to the vehicle’s occupants or persons outside the vehicle and/or property damage.
XDVD8285 OPERATION Safety Information Please read all instructions carefully before attempting to install or operate. Due to its technical nature, it is highly recommended that your DUAL XDVD8285 is installed by a professional installer or an authorized dealer. This product is only for use in vehicles with 12VDC negative ground only. Safety Notes: The DVD video display of the in-dash unit will not operate while the vehicle is moving. This is a safety feature to prevent driver distraction.
XDVD8285 INSTALLATION Preparation Please read entire manual before installation. Before You Start • Disconnect negative battery terminal. Consult a qualified technician for instructions. • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started • Insert the supplied keys between the radio and the sleeve at the left and right sides, and slide the unit out of the mounting sleeve.
XDVD8285 INSTALLATION Expanded Wiring Diagram - Inputs/Outputs Wiring Notes: Subwoofer output The SUBWOOFER audio output (Blue RCA) is active in all audio modes and must be connected to an external amplifier. Center output The CENTER audio output (Gray RCA) is only active in DVD 5.1 and Dolby Pro Logic II audio modes and must be connected to an external amplifier. Rear view camera A rear view camera (not included) can be used with the CAMERA input.
XDVD8285 INSTALLATION Wiring Diagram - Optional A/V Connections 7
XDVD8285 OPERATION IR Remote Preparation To first use the IR Remote control, you must first pull the battery insulation tape out Notes: • Remove the battery if the remote will not be used for a month or longer • Remove and dispose of battery properly Insert or replacing the Battery: Remove the battery holder Main Remote Remove the battery from the battery holder Install the new battery Make sure to keep the (+) side up Insert the battery holder Multi-zone Remote • CAUTION!!! Do not store battery
XDVD8285 OPERATION Control Locations - Monitor Closed 1 7 2 8 3 9 4 10 5 11 6 12 13 14 1 Power/Mute 8 Channel/Chapter/Track Up 2 AM/FM Mode - Hotkey 9 Channel/Chapter/Track Down 3 Auto Store/Preset Scan 10 Play/Pause 4 Mode 11 Info/Picture 5 Menu 12 Reset 6 Rotary Encoder/Enter 13 Open/Close Monitor/Angle Adjust 7 DVD Mode - Hotkey 14 Microphone Monitor Notes: • • • 9 T his model incorporates a motorized moving monitor.
XDVD8285 OPERATION Control Functions - Monitor Closed Power On/Off Mute AM/FM Mode - Hotkey AS/PS Press to turn the unit on. Hold for 3 seconds to turn the unit off. Press MUTE to silence the audio; 00 will appear in the OSD (On Screen Display). Press MUTE again to cancel. Press AM/FM to select radio tuner mode. If the unit is already in tuner mode, press AM/FM to select between FM1, FM2, FM3, and AM bands.
XDVD8285 OPERATION Control Functions - Monitor Closed Up Arrow This button performs different functions depending on the current mode. button can be found in each individual section. A detailed description of the Down Arrow This button performs different functions depending on the current mode. button can be found in each individual section. A detailed description of the Play/Pause Press to pause or continue playback of an audio or video track. Note: This button is only active in Disc and SD modes.
XDVD8285 OPERATION Control Locations and Functions - Monitor Open 1 3 2 4 1 Disc slot 2 SD card slot 3 Disc-in indicator Red = Disc inserted Blue = No disc inserted 4 When the panel is fully open, press to eject the disc. Safety Notes: The DVD video display of the in-dash unit will not operate while the vehicle is moving. This is a safety feature to prevent driver distraction. In-dash DVD video functions will only operate when vehicle is in Park and the parking brake is engaged.
XDVD8285 OPERATION Control Locations - Main Remote 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 1 Mode 16 Info 31 Root 2 Mute 17 Search 32 Repeat 3 Open/Close 18 Key #0 33 Chapter/Track Down 4 Power 19 Band/Stop 34 Chapter/Track Up 5 Key #1 20 Audio Select 35 Fast Reverse 6 Key #2 21 Escape 36 Fast Forward 7 Key #3 22 4-Way - Up 37 Zoom 8 Volume Up 23 Menu 38 Audio 9 Ke
XDVD8285 OPERATION Control Functions - Main Remote Mode Press once to incrementally select desired source. Mute Press once to MUTE audio, press again to return audio. Open/Close Power Keys 0-9 Volume Up Volume Down Info Search Band/Stop Audio Select Escape 4-Way-Up/Down/Left/Right Menu Picture OK Repeat A-B Press once to open monitor, press again to close the monitor. Press once to turn the unit on, press again to turn unit off. Direct access chapter/track/preset station for current BAND.
XDVD8285 OPERATION Control Locations - Multi-Zone Remote 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 20 21 23 24 26 27 18 19 22 25 28 29 30 32 31 33 1 Key #1 12 Key #9 23 Stop 2 Key #2 13 Key #0 24 Play/Pause 3 Key #3 14 Title Menu 25 Zoom 4 Multi-Zone Mode 15 4-Way - Up 26 Fast Reverse 5 Multi-Zone Mute 16 Root 27 Fast Forward 6 Key #4 17 4-Way - Left 28 Slow 7 Key #5 18 OK 29 Repeat 8 Key #6 19 4-Way - Right 30 Audio 9 Search 20 Chapter/Track
XDVD8285 OPERATION Control Locations - Multi-Zone Remote Mode Press once to incrementally select desired Multi-Zone source. Mute Press once to MUTE Multi-Zone audio, press again to return audio. Keys 0-9 Search Direct access chapter/track. Search function in the DVD mode. Title Menu Enters the title menu on DVD/Activates thumbnail view for JPG. Root Menu Enters the main menu of the DVD.
XDVD8285 OPERATION General Operation Power On/Off Mute Press to turn the unit on. Hold for 3 seconds to turn the unit off. Press MUTE to silence the audio; 00 will appear in the OSD (On Screen Display). Press MUTE again to cancel. Mode Press MODE to select between Tuner, Disc, XM, Camera, SD and Aux AV inputs. Modes of operation are indicated in the OSD (On Screen Display). XM tuner and SD card (all optional) must be connected/inserted to appear in the MODE selection string.
XDVD8285 OPERATION General Operation INFO/PIC Monitor Brightness CVBS Screen Controls Press PIC momentarily to display DVD disc information. Press and hold PIC for 2 seconds to change monitor BRIGHTNESS: to increase, to decrease, or turn the rotary to adjust the level up Press or down. (0 minimum/20 maximum) 10 is default. While in Aux or Camera mode: Press and hold PIC for 2 seconds to access PICTURE MENU.
XDVD8285 OPERATION General Operation - Main Menu Main Menu Access There are three methods to access the MAIN menu: • Press MENU button on the front panel. • Press MENU button on the main remote control. • Touch the upper left corner of the touch screen. 1 2 3 4 5 6 15 14 L 13 12 11 5 10 Touch Access Buttons 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14) 15) Rapid Dial Rotary Encoder 19 9 8 7 Touch to access AM/FM TUNER mode.
XDVD8285 OPERATION GENERAL Setup - Menu L General Setup Menu • • • Press GENERAL icon to access the GENERAL setup mode. Select desired parameter you wish to change. Page will return back to previous screen after 10 seconds of inactivity or by pressing the RETURN button.
XDVD8285 OPERATION GENERAL Setup - Menu L General Setup Menu L Press GENERAL icon to access the GENERAL setup mode. Press PAGE icon in the lower right corner. Select desired parameter you wish to change. Page will return back to previous screen after 15 seconds of inactivity or by pressing the RETURN button.
XDVD8285 OPERATION GENERAL Setup - Adjusting Radio Frequency Adjusting Radio Frequency L 1 Step 1 1) Touch top left corner of screen. Step 2 L 2 2) Touch GENERAL icon. L 3 Step 3 3) Touch USA. L L 5 4 Step 4 4) Touch the setting for your region. Step 5 Touch RETURN to exit.
XDVD8285 OPERATION GENERAL Setup - Adjusting the Clock 12Hr Clock Mode L 1 Step 1 1) Touch top left corner of screen. Step 2 L 2 2) Touch GENERAL icon. L 3 Step 3 3) Touch 00:00 area in the CLOCK row. L 7 L L L 8 5 6 Steps 4-8 4) Keypad will appear. 5) Enter HOURS, touch OK. 6) Enter MINUTES, touch OK. 7) Touch AM or PM to set. 8) Touch RETURN to exit. 24Hr Clock Mode 23 For 24Hr format, select 24Hr from CLOCK MODE, then follow steps 1-8.
XDVD8285 OPERATION GENERAL Setup - Setting the Anti-theft code Default Anti-theft password is 0000 and is turned off. To turn this feature on, follow the steps below. CAUTION!! This will lock your unit from operating if battery power is disconnected for more than 5 minutes. Step 1 & 2 L 1 L 2 1) Touch top left corner of screen. 2) Touch GENERAL icon.
XDVD8285 OPERATION SCREEN Setup - Menu Screen Setup Menu • • • L Press SCREEN icon to access the SCREEN setup mode. Select desired parameter you wish to change. Page will return back to previous screen after 15 seconds of inactivity or by pressing the RETURN button.
XDVD8285 OPERATION SCREEN Setup - Setting TFT Brightness This will set the default setting for the TFT display brightness. This can also be set by pressing the INFO button on the front TFT panel. Step 1 Step 2 L 1 1) Touch top left corner of screen. L 2 2) Touch SCREEN icon. L 3 Step 3 3) Touch [-] to reduce brightness. L L 5 4 Step 4 4) Touch [+] to increase brightness. 0 - 20 is possible Default = 10 Step 5 5) Touch RETURN to exit.
XDVD8285 OPERATION SCREEN Setup - Setting TFT Angle Set for best viewing angle for your vehicle L 1 Step 1 1) Touch top left corner of screen. Step 2 L 2 2) Touch SCREEN icon. L 3 Step 3 3) Touch a number displayed in SCREEN TILT row. L L 5 4 Step 4 4) Touch desired angle for best viewing angle. 1 - 6 is possible Default = 4 Step 5 27 5) Touch RETURN to exit.
XDVD8285 OPERATION SCREEN Setup - Touch Screen Calibration Upon initial installation or occasionally, the touch screen may have to be calibrated. Follow these steps as described. Step 1 L 1 1) Touch top left corner of screen. L 2 Step 2 2) Touch SCREEN icon. LL 3 Step 3 & 4 4 3) Touch No in TS Calibration row. 4) Then touch Yes. L 5 Notes: For proper calibration you must touch each pointer for 2 seconds.
XDVD8285 OPERATION ASP Config - Audio Settings Notes: Bass Freq Treble Freq Sub Filter These settings affect the quality of the audio in "Downmix" mode only and are primarily for use by a professional installer. For the casual user, it is recommended to only adjust the general sound quality by using the Audio Setup Menu, which is accessed by pressing the SEL button on the remote or pressing the rotary for 3 seconds. Sets the bass center frequency for optimal bass effect.
XDVD8285 OPERATION ASP Config - Audio Settings L Notes: FM/AM Gain DVD Gain The Gain settings allow you to customize the relative volume of the various modes to compensate for volume differences between the sources. The range is adjustable between -7 to +7, with 0 being the reference point (default level). Adjusts the relative volume in AM/FM Tuner mode. Adjusts the relative volume in DVD/CD/MP3/WMA mode. Bluetooth Gain Adjusts the relative volume in Bluetooth mode.
XDVD8285 OPERATION AM/FM Tuner Operation - OSD Overview 1 2 3 4 5 20 19 6 7 18 17 16 15 14 Tuner Mode 31 13 12 11 10 9 8 From the main menu, touch TUNER icon on the screen, or press the AM/FM button to select AM/FM Tuner mode. 1 Current Source Indicator Displays source currently playing. 2 Preset Number Indicator Shows what preset has been selected. 3 Stereo Indicator Shows that the frequency selected is received in stereo.
XDVD8285 OPERATION AM/ FM Tuner Operation - OSD Overview 9 Tune Frequency - Up Touching this icon will tune the radio to a higher frequency by one frequency step. 10 Tune Frequency - Down Touching this icon will tune the radio to a lower frequency by one frequency step. 11 Seek Next Station - Up Touching this icon will tune to the next strong station at a higher frequency. (This function can also be performed by pressing .
XDVD8285 OPERATION AM/FM Tuner Operation AM/FM Tuner Mode From the main menu, touch TUNER icon to select AM/FM Tuner mode. Press the AM/FM button. From the remote control or the front panel: Press MODE until TUNER is displayed on the screen. Band on the screen repeatedly until the desired band is displayed, FM-1, Touch FM-2, FM-3, or AM. Press the AM/FM button to switch between bands, FM-1, FM-2, FM-3, AM. From the remote control: Press the BAND button.
XDVD8285 OPERATION AM/ FM Tuner Operation Preset Scan Touching the button will scan through all tunable presets in the current band and play them for 10 seconds each. Press the AS/PS button momentarily. Direct Preset Tuning To select a desired station from the preset station list, touch any of the displayed station frequencies from the list. Use Rapid Dial by pressing in on the rotary, turn clockwise or counter-clockwise, and pressing in again to select the highlighted channel.
XDVD8285 OPERATION WARNING Upon installation of this Monitor/DVD player (“unit”) into a vehicle, the driver of the vehicle must not operate this unit by watching videos or playing video games while driving. Failure to follow this instruction could lead to driver distraction which could result in serious injury or death to the vehicle’s occupants or persons outside the vehicle and/or property damage.
XDVD8285 OPERATION DVD Operation - Parking Brake Initialization SAFETY WARNING CAUTION !!! IT'S UNLAWFUL TO OPERATE A VEHICLE WHILE VIDEO IS DISPLAY IN THE DRIVERS VIEWING AREA ENGAGE EMERGENCY BRAKE TO ENJOY VIDEO Front Monitor Video Initialization • The video display of the in-dash unit will not operate while the vehicle is moving. This is a safety feature to prevent driver distraction. In-dash video functions will only operate when vehicle is in Park and the PARKING BRAKE is engaged.
XDVD8285 OPERATION DVD Operation DVD Region Management Some DVD discs can be played only in certain playback modes according to the intentions of the software. As the XDVD8285 plays discs according to their intentions, some functions may not work as intended. Please be sure to read the instructions provided with each disc. This player has been designed to play back DVD software that has been encoded for specific region areas.
XDVD8285 OPERATION DVD Operation - Inserting a Disc Eject button DVD Loading Slot Insert CD/DVD with label facing upwards Inserting a Disc Open panel to reveal disc slot by pressing . With the label facing up, insert a standard size disc into the slot. The panel will close and the disc will automatically begin playback. Other sub-menus may have to be pressed to access the DVD movie/music content. Read the directions of your specific DVD disc for other features.
XDVD8285 OPERATION DVD Operation - Touch Screen Controls Hidden Touch Screen area while in TUNER mode There are several hidden TOUCH SCREEN areas as outlined below: "A" area can be used in any mode to access MAIN menu.
XDVD8285 OPERATION DVD Operation - Touch Screen Controls Using the hidden Touch Screen Controls A - Displays MAIN menu B - Displays DVD disc information C - Selects PREVIOUS chapter D - Select NEXT chapter E - Displays the full DVD transport controls F - GOTO search menu L L AREA A Access MAIN Menu Note: A DVD disc must be inserted to access these functions and features.
XDVD8285 OPERATION DVD Operation - Touch Screen Controls 1 Using the hidden Touch Screen Controls 2 Touch AREA E 3 DVD Mode 41 4 5 6 7 8 9 From the main menu, touch the DISC icon on the screen, or press DVD button to select DVD mode. 1 Title Menu Jumps to the DVD Title menu. 2 Sub-Title Mode Activates sub-titles and cycles between multiple sub-title languages. 3 Play/Pause Touch the 4 Stop 5 Fast Reverse Touch the icon to fast reverse at 2x speed.
XDVD8285 OPERATION DVD Operation - Searching a DVD Searching a DVD L Searching by Time, Title or Chapter Touch Area F to bring up the Search Window. The Search Window allows a search for a specific time, title or chapter. Search by TIME example To search for a specific time, touch the --:--:-- area and an on-screen keyboard will pop up. Use the keyboard to enter a time and touch OK. (For example, to skip to 1 hour, 12 minutes and 19 seconds into the DVD, touch: 1 1 2 1 9 OK.
XDVD8285 OPERATION DVD Operation Playback Control Touch Area E to bring up the on-screen buttons. to fast forward or to fast reverse. Touch Each subsequent press of the button will change the speed from normal to 2x to 4x to 8x to 20x and back to 1x. Hold the Hold the button to fast forward. button to fast reverse. From the remote control: to fast forward. Press to fast reverse. Press Repeat Mode Touch the Repeat button to repeat either a chapter or title.
XDVD8285 OPERATION DVD Operation Sub-Titles Touch the SUB.T button to activate Sub-Title mode and select a sub-title language. Each touch will cycle the mode from off to language 1, language 2, etc., and back to off. From the remote control: Press the SUB-T button to control Sub-Title mode. Notes: • Not all DVDs have sub-titles and when they do, some will only have 1 language. Therefore this function may be disabled or limited. • The Sub-Title Mode can only be changed while the DVD is playing.
XDVD8285 OPERATION DVD Setup Menu - Language LANGUAGE Setup Menu Note: A DVD disc must be inserted to access these functions and features. With the unit in DVD mode, press AREA A (top left screen) to display the MAIN menu. Press DVD Setup to access the DVD setup menu. L L Press the LANGUAGE icon to select LANGUAGE setup page. Disc Subtitle Press to select desired disc subtitle language. L Audio Language L Press to select desired disc audio language.
XDVD8285 OPERATION DVD Setup Menu - Audio Audio Setup Menu Note: A DVD disc must be inserted to access these functions and features. With the unit in DVD mode, press AREA A (top left screen) to display the MAIN menu. Press DVD Setup to access the DVD setup menu. L L Press the AUDIO icon to select from the following menus: Pink Noise Press to activate pink noise generator for the desired channel. The pink noise generator is used to set the relative speaker levels for multi-channel playback.
XDVD8285 OPERATION DVD Setup Menu - Audio Center Control Press to select desired center channel time delay. The distance is defined in milliseconds. 5ms 4ms 3ms 2ms 1ms 0ms = DEFAULT L Rear Control Press to select desired rear channel time delay. The distance is defined in milliseconds. 15ms 12ms 9ms 6ms 3ms 0ms = DEFAULT L Down Sampling Select On to activate audio down sampling. The DVD audio output will be downsampled to 48kHz. The original sampling frequency is preserved when Off is selected.
XDVD8285 OPERATION DVD Setup Menu - Video Video Setup Menu Note: A DVD disc must be inserted to access these functions and features. With the unit in DVD mode, press AREA A (top left screen) to display the MAIN menu. Press DVD Setup to access the DVD setup menu. L L Press the VIDEO icon to select from the following menus: TV Shape Press to select desired TV shape. L 4:3 16:9 = DEFAULT NORMAL - 4:3 L WIDE - 16:9 Angle Mark Select On to activate angle mark.
XDVD8285 OPERATION DVD Setup Menu - Speaker Speaker Setup Menu Note: A DVD disc must be inserted to access these functions and features. With the unit in DVD mode, press AREA A (top left screen) to display the MAIN menu. Press DVD Setup to access the DVD setup menu. L L Press SPEAKER icon to select from the following menus: Speaker Mode Select desired speaker output mode. Full 6CH DownMix = DEFAULT L *Front Speaker Size L Select size of front speaker.
XDVD8285 OPERATION DVD Setup Menu - Speaker *Surround Speaker Size Note: A DVD disc must be inserted to access these functions and features. *Subwoofer Speaker Select size of surround speaker. Large = DEFAULT Small None L Select Present if a subwoofer is included in your system. Present None = DEFAULT L *Center Speaker Size Press to select size of center speaker.
XDVD8285 OPERATION DVD Setup Menu - Pro Logic II Pro Logic II Setup Menu Note: A DVD disc must be inserted to access these functions and features. With the unit in DVD mode, press AREA A (top left screen) to display the MAIN menu. Press DVD Setup to access the DVD setup menu. L L Press the Pro Logic II icon to select from the following menus: Decode Mode Select desired decode mode. Off Pro Logic PLII Matrix PLII Movie PLII Music = DEFAULT L *Panorama L Select On to activate panorama mode.
XDVD8285 OPERATION DVD Setup Menu - Pro Logic II *Dimension Select desired dimension. Note: A DVD disc must be inserted to access these functions and features. L 0 1 2 3 = DEFAULT 4 5 6 Changing the dimension control allows you to adjust the soundstage either towards the front or towards the rear. *Center Width Select desired center channel width.
XDVD8285 OPERATION DVD Setup Menu - Rating Rating Setup Menu Note: A DVD disc must be inserted to access these functions and features. With the unit in DVD mode, press AREA A (top left screen) to display the MAIN menu. Press DVD Setup to access the DVD setup menu. L L Press the RATING icon to select from the following menus: Enable Parental Lock Password Press ---- to enter a password. L Setting Parental Lock Password Rating Setting L 1. Enter a 4-digit code 2. Write the code down 3.
XDVD8285 OPERATION CD Operation - OSD Overview 1 2 3 4 20 5 6 19 18 7 8 17 16 15 CD Mode 14 13 12 11 10 9 From the main menu, touch the DISC icon on the screen, or press the DVD button to select CD mode. 1 Current Source Indicator Displays Source Currently Playing 2 Track Number Indicator Displays current track number and total number of tracks on the disc. 3 Disc Title Indicator Displays current disc title when available.
XDVD8285 OPERATION CD Operation - OSD Overview 55 7 Scroll bar Allows scrolling of track list. 8 Direct Select Keyboard icon to display a numeric keyboard. Enter desired track Touch the number and touch OK to select it. 9 Track Scan Touch the SCAN icon to listen to 10 seconds of each track in order. This icon will remain highlighted until touched to disable. 10 Fast Forward Touch the icon to fast forward at 2x speed.
XDVD8285 OPERATION CD Operation Playing CD-DA discs After inserting a CD disc, files will play in numerical order in the directory. L Selecting by Keypad Touch to display keypad. Enter desired track number and press OK. L Selecting by Direct Track Access Touch desired track for DIRECT TRACK access. L L Previous/Next Page Touch to view UP/DOWN pages of available tracks.
XDVD8285 OPERATION CD Operation Page Up/Down The Page Up and Page Down on-screen buttons can be used to see the rest of the tracks on the CD. Use the Direct Select method to play a desired track. From the remote control: Press to display the next page. Press to display the previous page. Track Select Press Press button to skip to the next track. button to skip to the previous track. From the remote control: to skip to the next track. Press to skip to the previous track.
XDVD8285 OPERATION CD Operation Shuffle Mode Touch the Shuffle button to shuffle all of the tracks on the CD. The Shuffle button will be illuminated while Shuffle Mode is active. When the button is illuminated, touching it a second time will disable Shuffle Mode. Notes: The shuffled order of the songs is fixed, therefore the Track Select operations will continue to operate properly within the shuffled order.
XDVD8285 OPERATION MP3/WMA Operation - OSD Overview 1 2 3 4 5 6 23 7 8 22 9 21 10 20 19 18 MP3/WMA Mode 59 17 15 16 14 13 12 11 From the main menu, touch the DISC icon on the screen, or press the DVD button to select MP3/WMA mode. 1 Current Source Indicator Displays source currently playing. 2 Song Number Indicator Displays current song number and total number of songs on the disc. 3 Master Song Number List Shows the number of the song relative to the entire disc.
XDVD8285 OPERATION MP3/WMA Operation - OSD Overview 9 Scroll bar Allows scrolling of song list. 10 Direct Select Keyboard icon to display a numeric keyboard. Enter desired Touch the song number and touch OK to select it. 11 Fast Forward icon to fast forward at 2x speed. Touch Each touch changes speed from 2x to 4x to 8x to 20x then to 1x play. 12 Next Folder Pressing this button will select the next available folder.
XDVD8285 OPERATION MP3/WMA Operation Folder Select Page Up/Down From the remote control: Press to display the next page. Press to display the previous page. Note: Continued operation of the Page Up and Page Down buttons will display the next and previous folders, respectively once the songs in the current folder have all been displayed.
XDVD8285 OPERATION MP3/WMA Operation Song Control You can use the Fast Forward on-screen button to speed up the playback of a song. Each subsequent press of the button will change the speed from normal to 2x to 4x to 8x to 20x and back to 1x. Hold the Hold the button to fast forward. button to fast reverse. From the remote control: to fast forward. Press to fast reverse. Press Note: Song control only works for MP3 type files and there is no audio output while song control is active.
XDVD8285 OPERATION SD Card Operation 1 2 3 4 5 6 23 7 8 9 22 21 10 20 19 18 SD Mode 63 17 15 16 14 13 12 11 From the main menu, touch the SD icon on the screen. 1 Current Source Indicator Displays source currently playing. 2 Song Number Indicator Displays current song number and total number of songs on the disc. 3 Master Song Number List Shows the number of the song relative to the entire disc. 4 Folder Displays the name of the currently selected folder.
XDVD8285 OPERATION SD Card Operation 9 Scroll bar Allows scrolling of song list. 10 Direct Select Keyboard icon to display a numeric keyboard. Enter desired song Touch the number and touch OK to select it. 11 Fast Forward Touch the icon to fast forward at 2x speed. Each touch changes speed from 2x to 4x to 8x to 20x then to 1x play. 12 Next Folder Pressing this button will select the next available folder.
XDVD8285 OPERATION SD Card Operation Folder Select Page Up/Down From the remote control: Press to display the next page. Press to display the previous page. Note: Continued operation of the Page Up and Page Down buttons will display the next and previous folders, respectively once the songs in the current folder have all been displayed.
XDVD8285 OPERATION SD Card Operation Song Control You can use the Fast Forward on-screen button to speed up the playback of a song. Each subsequent press of the button will change the speed from normal to 2x to 4x to 8x to 20x and back to 1x. Hold the Hold the button to fast forward. button to fast reverse. From the remote control: to fast forward. Press to fast reverse. Press Note: Song control only works for MP3 type files and there is no audio output while song control is active.
XDVD8285 OPERATION JPEG Operation - OSD Overview 1 7 2 3 JPEG Mode 67 4 5 6 JPEG mode works a bit differently from the other modes. There is no separate JPEG mode, rather this mode is accessed within either SD mode or MP3/WMA mode. Whenever a picture is present on an SD card or CD, the unit will switch to the JPEG mode to view it. Each picture is displayed on the screen for 5 seconds, unless paused. JPEG mode will automatically exit when the next file is not a picture, or when STOP is pressed.
XDVD8285 OPERATION JPEG Operation Play/Pause Press PLAY/PAUSE to stop the viewer on a specific picture or to resume. From the remote control: Press OK to temporarily stop and resume the viewer. Note: Unlike the music player, when the viewer is paused, moving to the next or previous picture will not automatically resume the slideshow. Next/Previous Touch Area D to skip to the next file/image. Touch Area B to skip to the previous file/image. Press Press to skip to the next file/image.
XDVD8285 OPERATION Media Compatibility Media Compatibility The following types of discs/files are compatible: • CD-ROM (ISO), CD-R, CD-RW, DVD+R/RW, DVD-R/RW • CD-DA, DVD Video • MP3 data • WMA data • JPG images The following types of discs/files are not compatible: • WMA files that are protected by DRM (Digital Rights Management) • WMA lossless format • Discs recorded with Track At Once or packet writing • MP3 PRO format • MP3 playlists • WAV format • WMV format • DivX format • AVI format • MPG format So
XDVD8285 OPERATION Media Compatibility Additional MP3/WMA Information An internal buffer provides ESP (Electronic Skip Protection) to virtually eliminate skipping. When playing a disc recorded with regular audio files (CD-DA or .WAV) and MP3/WMA files, the unit will play the MP3/WMA files only. Only MP3 files with filename extension (.mp3) can be played. Only WMA files with filename extension (.wma) can be played. Do not attempt to play discs which contain non-MP3/WMA files with the MP3/WMA extension.
XDVD8285 OPERATION XM Radio - OSD Overview (Optional) 1 2 3 4 5 6 23 22 21 7 20 19 8 18 17 16 XM Mode 71 15 14 13 12 11 10 9 From the main menu, touch the XM icon on the screen. 1 Current Source Indicator Displays source currently playing. 2 Signal Strength Indicator Displays the strength of XM reception. 3 Current Station Indicator Displays the current XM channel number.
XDVD8285 OPERATION XM Radio - OSD Overview (Optional) 8 Direct Select Keyboard Displays on-screen keyboard to select a channel by number. 9 Channel Scan Pressing this button will scan through all available channels, starting from the current channel, pausing for 10 seconds on each channel. 10 Category Next Channel Pressing this button will select the next available channel in the current category.
XDVD8285 OPERATION XM Radio Operation (Optional) Activating Your XM Tuner (when connected) 1. Select XM mode. 2. Verify channel 1 (XM Preview Channel) is playing. 3. Select Channel 0. The XM tuner's eight character Radio ID number will appear at the top of the screen. The Radio ID number is also located on the XM tuner (sold separately). 4. Record the number here for future reference: 5. Activate your XM Satellite Radio service by logging on to http://www.xmradio.com/activation or call 1-800-967-2346.
XDVD8285 OPERATION XM Radio Operation (Optional) From the remote control: Press or to scroll through the channels. When the desired channel is highlighted press OK. Direct Channel Entry icon to display a numeric keyboard. Enter desired channel Touch the number and touch OK to select it. From the remote control: Use the numeric keypad to enter the desired channel number. Category Mode icon to display a list of categories.
XDVD8285 OPERATION Bluetooth® - OSD Overview (Optional) 1 2 3 4 5 11 6 10 9 8 Before using the Bluetooth Bluetooth Mode 75 7 Select the Bluetooth option in the General setup and select On to activate the Bluetooth feature. Refer to page 21 for more details. From the main menu, touch the Bluetooth icon on the screen or, press the Bluetooth icon at the top of the screen. The Bluetooth function must be turned on for the Bluetooth icon to appear at the top of the screen.
XDVD8285 OPERATION Bluetooth® - OSD Overview (Optional) 7 Audio Transfer Button Press to transfer audio between the head unit and mobile phone. 8 End button 9 Setup Menu Icon Press to access Bluetooth setup menu. 10 Phone book Icon Press to access the phone book menu. 11 Keypad Interface Icon Press to display the keypad interface. Press to end a call in progress or to reject an incoming call.
XDVD8285 OPERATION Bluetooth® - Setup Menu (Optional) Pairing Before you can use a mobile device with this head unit, it must be authenticated. This is also referred to as "pairing" a device. Note: Please make sure that Bluetooth is activated on your mobile device before you begin the pairing process. Refer to the owner's manual of your mobile device for more details. Step 1 Access Bluetooth setup menu and press Yes to begin the pairing process. The head unit will display "Wait Pairing..
XDVD8285 OPERATION Bluetooth® - Operation (Optional) Phone Book Menu Incoming Call Screen Dialed Calls Press Dialed Call to retrieve the list of dialed calls from the mobile device. "Searching", then "Loading dialed phone book" will be displayed during the retrieval process followed by "The phone book is done". Touch the desired name to call. Press the page up/down buttons to navigate through the pages. Received Calls Press Received Call to retrieve the list of received calls from the mobile device.
XDVD8285 OPERATION General Operation - Multi-Zone Menu Multi-Zone Menu Access There are two methods to access the Multi-Zone menu • Press the MENU button on the front panel, then press Multi-Zone • Touch the upper left corner of the touch screen, then press Multi-Zone 1 2 3 4 13 L 12 11 10 9 8 Touch Access Buttons 1 2 3 4 5 6 7 8 9 10 11 12 13 Rapid Dial 7 5 Touch to set CD/DVD mode as the Multi-Zone mode, (CD/DVD must be inserted) Touch to set CAMERA mode as the Multi-Zone mode, if optional c
XDVD8285 OPERATION General Operation - Multi-Zone Menu Multi-Zone Operation Independent sources can be played simultaneously on the unit. For example, the AM/FM tuner mode can be selected for the front zone while DVD video is selected for the Multi-Zone source (for headrest monitors, overhead monitors, etc.). Select a Source for the Multi-Zone 1. Press the MENU button, then touch Multi-Zone to access the Multi-Zone menu. Select desired Multi-Zone source. 2.
XDVD8285 OPERATION Multi-Zone - AM/FM Tuner Operation 15 1 14 2 13 3 12 4 11 10 9 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 81 8 7 6 5 Clock indicator - displays current time. Multi-zone mode indicator - displays current multi-zone source. Preset page up/down arrows - press to select the next or previous preset page. Preset number list display - shows the preset station list by frequency. Touch frequency to select a preset. Touch and hold frequency to store presets.
XDVD8285 OPERATION Multi-Zone - XM Radio Operation 1 12 2 11 10 9 8 7 6 5 1 2 3 4 5 6 7 8 9 10 11 12 Channel Up Channel Down 4 3 Clock indicator - displays current time. Multi-zone mode indicator - displays current multi-zone source. Channel scan - touch to scan through all available channels, pausing for 10 seconds on each channel. Touch again to cancel. SCAN will change to green when the scan function is active.
XDVD8285 WARRANTY Limited One Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase. Dual Electronics Corp.
XDVD8285 OPERATION Troubleshooting General Problem Unit will not turn on (no power) Unit has power (but no sound) Unit blows fuse Unit has audio (but no video) No video display (when in reverse) Cause Action Yellow wire not connected or incorrect voltage Check connections for proper voltage (11~16VDC) Red wire not connected or incorrect voltage Black wire not connected Check connection to ground Fuse blown Replace fuse Speaker wires not connected Check connections at speakers One or more speaker
XDVD8285 OPERATION Troubleshooting Bluetooth Problem Cause Please connect first appears in the display There is no mobile device connected to the head unit Pair and or connect a mobile device to the head unit as described on page 83 Bluetooth function is not active on the head unit Activate Bluetooth function as described on page 21 Bluetooth function is not active on the mobile device Refer to the owner's manual of your mobile device Mobile device will not connect to the head unit Action A mobi
XDVD8285 OPERATION Specifications DVD Player Frequency response: 10Hz-20kHz Channel separation @ 1kHz: >65dB D/A converter: 24 Bit FM Tuner Tuning range: 87.5MHz-107.9MHz Usable sensitivity: 8.5dBf 50dB quieting sensitivity: 10dBf Stereo separation @ 1kHz: 40dB Frequency response: 30Hz-13kHz AM Tuner Tuning range: 530kHz-1710kHz Usable sensitivity: 22uV Frequency response: 30Hz-2.2kHz Monitor Panel size: 6.5” (165.
Dual Electronics Corp. Toll Free: 1-866-382-5476 www.dualav.com ©2010 Dual Electronics Corp. All rights reserved.
