X2DMA400 INSTALLATION/OWNER'S MANUAL AM/FM Receiver with Remote Control TM
X2DMA400 OPERATION Preparation Please read entire manual before installation. Before You Start • Disconnect negative battery terminal. Consult a qualified technician for instructions. • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started • Remove trim ring from unit, • Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve.
X2DMA400 OPERATION Wiring Diagram YELLOW - Rear RCA Input Connect a portable device BLACK - Antenna Input Connect the vehicle antenna RCA Preamp Outputs External Amplifer Connections Steering Wheel Interface Input (PAC SWI-PS sold separately) SiriusXM Vehicle Tuner Connection (tuner sold separately) FUSE When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The X2DMA400 uses one 10 amp ATM fuse located beside the wiring connector.
X2DMA400 OPERATION Control Locations - Receiver 1 3 2 21 20 4 19 5 18 17 16 15 14 13 7 12 8 9 11 10 1 Source / Power ( ) 12 USB Port 2 Eject 13 Preset 6 / Folder Up 3 Mute / Tag 14 Preset 5 / Folder Down 4 Display 15 Preset 4 / Play / Pause 5 Volume Knob 16 Preset 3 / Intro 6 Back / Band 17 Preset 2 / Random 7 Select 18 Preset 1 / Repeat 8 Audio / Menu 19 Tune / Track Up 9 Tuning Knob 20 Reset 10 Auxiliary Input 11 SD Card Slot 4 6 21 Tune / Track Down
X2DMA400 OPERATION Control Locations - Remote 1 2 3 4 5 21 6 20 7 19 8 18 9 17 10 16 11 15 12 14 13 1 Source / Power ( ) 12 Key 9 2 Select 13 Category Up (SXM) 3 Volume Up 14 Key 0 / Display 4 Audio / Menu 15 Category Down (SXM) 5 Tune / Track Up 16 Key 7 6 Volume Down 17 Key 8 7 Mute / Tag 18 Preset 4 / Play / Pause 8 Preset 2 / Random 19 Preset 1 / Repeat 9 Preset 3 / Intro 20 Band / Back 10 Preset 6 / Folder Up 21 Tune / Track Down 11 Preset 5
X2DMA400 OPERATION General Operation Power On/Off Source Press or any other button to turn unit on. Press and hold to turn unit off. Press SOURCE to select one of the following audio sources: AM/FM Tuner Mode CD Player Mode Auxiliary Input (front/rear) Modes USB and Operation of iPod/iPhone Modes SD Card Mode SiriusXM Satellite Radio Mode When a source is selected, a red line will appear underneath the corresponding icon in the source indicator bar beneath the LCD.
X2DMA400 OPERATION General Operation Auxiliary Input Volume Insert 3.5 mm plug to connect your portable audio device. Adjust volume using volume knob (00-46). Mute Press MUTE to silence the audio. Press MUTE again to cancel. Reset Press the RESET button, located in the bottom left corner of the front panel, to reset the unit back to the factory settings if abnormal operation occurs. Display Set the Clock Press DISP to toggle between items such as clock, radio frequency, or ID3 tag song information.
X2DMA400 OPERATION Setup Menu Press and hold AUDIO/MENU for more than 3 seconds to access the setup menu, then press AUDIO/MENU to cycle through menu options. When desired option appears in the display, rotate the tuning knob left/right to adjust or activate desired function. Press BACK to exit any menu or submenu. Function Options Action Auto Station Store AUTO PGM STATIONS Press SELECT to begin automatically programming strong radio stations to the 6 preset buttons in the current band.
X2DMA400 OPERATION Audio Menu Press AUDIO/MENU momentarily to cycle between Bass, Treble, Balance, Fader, Equalizer, *Subwoofer, and Source Volume Level. Press BACK at any time to exit the audio menu. BASS TREBLE BALANCE FADER EQ SUBWOOFER SOURCE LEVEL Bass Press AUDIO/MENU until BASS appears, then rotate the tuning knob left/right to adjust (-6 minimum / +6 maximum). Treble Press AUDIO/MENU until TREBLE appears, then rotate the tuning knob left/right to adjust (-6 minimum / +6 maximum).
X2DMA400 OPERATION LCD Icon Layout Stereo FM Reception CD-in EQ Loudness Random Repeat SiriusXM Signal Indicator SiriusXM Intro Channel Number Artist Name File Name Song Title Album Name Folder Name AM/FM Tuner Operation Seek Tuning Manual Tuning Tuning - Remote Control Press TUNE station. nn or TUNE ll to seek the next strong Rotate the tuning knob to move radio frequency up or down one step at a time. Using the remote control: • Press TUNE or TUNE momentarily to perform Manual Tuning.
X2DMA400 OPERATION CD Player Operation Insert CD Eject CD Track Select Fast Forward/Reverse Pause Intro Repeat Random CD-R/CD-RW Compatibility With the label facing up, insert a standard size CD into the CD slot. The CD will automatically begin playback. Press EJECT to eject the CD. The unit will change to previous mode of operation. If the disc is not removed within 10 seconds, the unit will reload the disc. The unit does not have to be turned on to eject CD.
X2DMA400 OPERATION CD Player Operation - MP3/WMA Files MP3/WMA Discs Folder Access When an MP3/WMA encoded disc is first inserted, “READING” will appear in the display. Depending on the number of files and folders, this may take several seconds. Press Press to select the next folder. to select the previous folder. *Folder access is only available on discs recorded with more than one folder.
X2DMA400 OPERATION CD Player Operation - MP3/WMA Files File/Folder Search Press SELECT to enter the file/folder search mode. A list of all the folders from the CD will be displayed. Note: Any files located in the root directory will be located in the folder named "ROOT". Choose a Folder Turn the tuning knob to cycle through all the folders on the CD, and press SELECT to choose the desired folder. The list of files in the selected folder will be displayed.
X2DMA400 OPERATION CD Player Operation - MP3/WMA Files File/Folder Compatibility and Support • • Compatible File Types • • • • • • • Incompatible File Types • • • • • • Recording Format • Compatibility • Sampling Frequency • Rate Compatibility • Transfer Bit Rate • Compatibility • • • Character Support • • • • ID3 Tag Support • • File/Folder Limit • • 14 CD-ROM (ISO), CD-R, CD-RW CD-DA (digital audio) MP3 data (.mp3) WMA data (.wma) AAC data (.
X2DMA400 OPERATION Operation of iPod/iPhone Connecting an iPod/iPhone Device USB Connection Using the "dock connector to USB" sync cable (provided with the iPod/iPhone device), plug the USB cable into the X2DMA400's USB port. Once connected, playback will begin automatically.
X2DMA400 OPERATION Operation of iPod/iPhone Controlling a Device: Full Control - Music Search Menu The X2DMA400 features a powerful music search that simplifies the searching process. Follow the steps below to find the desired song: Begin Searching Press SELECT to begin the search. The main search menu will appear. Select a Category Turn the tuning knob to select between artists, albums, songs, playlists, podcasts and audiobooks. Press SELECT to select the desired search category.
X2DMA400 OPERATION Operation of iPod/iPhone Controlling a Device: Manual Control When the control of iPod/iPhone feature is set to "MANUAL" in the iPod Menu, use the following functions to control the device: Manual Control for iPod When "MANUAL" control is selected from the iPod Menu, the iPod or iPhone device can be controlled directly from the device's interface. All functions except for volume can be used from the iPod or iPhone device.
X2DMA400 OPERATION USB/SD Card Operation Connecting a USB Device (sold separately) To play MP3/WMA files from most mass storage devices,connect a device to the X2DMA400's USB port. Connecting a SD Card (sold separately) To play MP3/WMA files from an SD Card, insert an SD card into the X2DMA400's SD card slot with the label facing up, and press the card until it clicks into place. Remove the SD card by pressing in until it clicks, then pull to remove.
X2DMA400 OPERATION USB / SD Card Operation File and Folder Search Begin Searching Press SELECT to enter the file/folder search mode. A list of all the folders from the USB/SD device will be displayed. Note: Any files located in the root directory will be located in the folder named "ROOT". Choose a Folder Turn the tuning knob to cycle through all the folders on the device, and press SELECT to choose the desired folder. The list of files in the selected folder will be displayed.
X2DMA400 OPERATION USB / SD Card Operation File/Folder Compatibility and Support • • Compatible File Types • • • • • • • Incompatible File Types • • • • • • Recording Format • Compatibility • Sampling Frequency • Rate Compatibility • Transfer Bit Rate • Compatibility • • • Character Support • • • • ID3 Tag Support • • • File/Folder Limit • USB/SD File System SD Card Capacity 20 CD-ROM (ISO), CD-R, CD-RW CD-DA (digital audio) MP3 data (.mp3) WMA data (.wma) AAC data (.
X2DMA400 OPERATION SiriusXM Vehicle Tuner Connections Connecting the SiriusXM Vehicle Tuner (sold separately) SiriusXM Satellite Radio operation requires the connection of the SiriusXM-Connect Vehicle Tuner (sold separately). Note: The SiriusXM-Connect Vehicle Tuner must have the SiriusXM logo to be compatible with the X2DMA400. To connect the SiriusXM Vehicle Tuner, follow the instructions provided with the tuner.
X2DMA400 OPERATION SiriusXM Vehicle Tuner Operation Radio ID To view the Radio ID on the LCD, turn the tuning knob left or right until channel 0 appears. The 8 character Radio ID will appear on the display. The Radio ID is also printed on the underside of the SiriusXM Vehicle Tuner. Note: The Radio ID does not use the letters I, O, S, F.
X2DMA400 OPERATION SiriusXM Vehicle Tuner Operation SiriusXM Setup Menu To access the SiriusXM setup menu options, press and hold AUDIO/MENU for more than 3 seconds, press AUDIO/MENU to cycle through menu options until "SIRIUSXM SETUP" appears, then press SELECT. Press AUDIO/MENU to cycle through the list of submenu options. Function Action Options Description EDIT CODE Parental Controls Delete Tags (iTunes Tagging) *Enter Code (default: 0000) Choose this option to program a new 4-digit code.
X2DMA400 OPERATION SiriusXM Vehicle Tuner Operation Displayed Information Display Press DISP to cycle between the following options: (LINE 1) (LINE 2) CHANNEL NAME CATEGORY ARTIST SONG CONTENT INFO CLOCK CHANNEL Displays the name of the SiriusXM channel. CATEGORY Displays the category type of the current channel. ARTIST Displays the artist's name from the currently playing song. TITLE Displays the song title from the currently playing song.
X2DMA400 OPERATION iTunes® Tagging Operation Requirements Overview The iTunes Tagging feature of the X2DMA400 requires the optional SiriusXM Vehicle Tuner (sold separately). iTunes Tagging allows the user to "Tag" songs that are playing on SiriusXM Satellite Radio channel and enables them to be purchased later through iTunes.
X2DMA400 OPERATION iTunes® Tagging Operation Troubleshooting Displayed Message Description There is a compatibility issue with the iPod device that is connected. Check the list of compatible iPod devices below. CHECK iPod VER If the attached iPod device is compatible, update the firmware to the latest version using iTunes. Tags are being sent to the iPod device. This process can take several SENDING TAGS minutes depending on the number of Tags being sent.
X2DMA400 OPERATION Limited One Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase. Dual Electronics Corp.
X2DMA400 OPERATION Troubleshooting - General Problem Unit will not turn on (no power) Unit has power (but no sound) Cause Action Yellow wire not connected or incorrect voltage Red wire not connected or incorrect voltage Black wire not connected Fuse blown Speaker wires not connected Check connections for proper voltage (11~16VDC) One or more speaker wires touching each other or touching chassis ground Check connection to ground Replace fuse Check connections at speakers Insulate all bare speaker wir
X2DMA400 OPERATION Specifications FM Tuner Tuning range: 87.5MHz-107.9MHz Usable sensitivity: 8.5dBf 50dB quieting sensitivity: 10dBf Stereo separation @ 1kHz: 40dB Frequency response: 30Hz-13kHz AM Tuner Tuning range: 530kHz-1710kHz Usable sensitivity: 22uV Frequency response: 30Hz-2.2kHz General USB/SD Card Speaker output impedance: 4~8 ohms Line output voltage: 2 Volts RMS Dimensions: 7" x 6.7" x 4" (178 x 170 x 100 mm) File system: FAT, FAT32 File extensions support: .mp3, .
X2DMA400 OPERATION FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
X2DMA400 OPERATION Notes 31
Dual Electronics Corp. Toll Free: 1-866-382-5476 www.dualav.com ©2011 Dual Electronics Corp. All rights reserved. iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards.
