Installation Guide

ManualsBrandsDual-Lite ManualsOtherDual-Lite 2 Light Halogen 16 Watt Remote Capacity Indoor Emergency Light

High-Capacity Emergency Lighting Units

Installation Instructions For Standard,

Remote Capacity And Damp

Location Models

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed including the following.

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1. Do not use outdoors.

2. Do not mount near heaters or hot surfaces.

3. Equipment should be mounted in locations and at heights where it will not readily be subject to tampering by

unauthorized personnel.

4. The use of accessory equipment not authorized by the manufacturer may cause an unsafe condition.

Caution: Halogen cycle lamps may be used in this equipment. Halogen cycle lamps operate at high temperatures. Do not

  storeorplaceammablematerialsnearlamp.Toavoidshattering:Donotoperatelampinexcessofratedvoltage.Protect 

lamp against abrasion and scratches and against liquids when operating. Dispose of lamp with care.

5. Do not use this equipment for other than its intended purpose.

 6.Servicingofthisequipmentshouldbeperformedbyqualiedservicepersonnel.

SAVE THESE INSTRUCTIONS

WARNING – This product contains chemicals known to the State of California to cause cancer, birth defects and/or other

reproductiveharm.Thoroughlywashhandsafterinstalling,handling,cleaning,orotherwisetouchingthisproduct.

EMERGENCY LIGHTING AND POWER EQUIPMENT FOR USE IN DAMP LOCATIONS

Damp location listed units are suitable for use in:

1. Interior locations subject to moderate degrees of moisture, such as some basements, some barns, some cold-storage

warehouses, and the like.

 2.Partiallyprotectedlocationsundercanopies,marquees,roofedopenporchesandthelike.

GENERAL INSTRUCTIONS

This unit is designed for surface mounting on a wall or other sold surface (building support structure, column, etc.). Unit must be

mountedhighenoughtomaximizeilluminatedareaunderanticipatedconditionsofuse.Besuretoallowampleclearancefor

mounting and aiming the lighting heads.

Provideeachunitwithasingleunswitchedpowersupplyfroma120or277VACbranchcircuitusedfornormallightinginthesame

area. The wiring should be permanent installation, using appropriate size wire.

Note:De-energizeACcircuittounitduringinitialinstallation,andduringservicingorrelampingoperations.

PLACING THE UNIT IN SERVICE

 1. Loosenthetwocoverretainingscrewsonthesidesoftheunit,rotatetheheadsforclearance,andremovethecoverby 

lifting it up and outwards.

2. If lighting heads will be retained in the top mounted position, go to step 3. If lighting heads are to be relocated to side

mounted position, proceed as follows:

a. Snap out the lighting head knockouts on the sides of the unit.

b. Loosen the locking nut that retains the stem for each lighting head.

c. Slide each lighting head out of its present slot.

Note: It is not necessary to disconnect the lighting head leads from the circuit board.

d. Insert the stem of each lighting head into the side opening slots.

e. Tighten the locking nut on each stem so that the lamp heads turn with some resistance.

  f.Plugthetopmountedopeningslotswiththeholeplugscontainedinthehardwarepack.

 3. Fastenenclosuretoelectricaloutletboxand/orwallsurfaceusingappropriatehardware.

Note:Theenclosurecanbemountedto3˚”,4”octagon,or4”squareelectricalboxes,andtostandard

  plasterrings.Largeenclosureshaveadditionalkeyholeslotsforsurfacemounting.A

/8”diameter

  knockoutisprovidedonthetopandoneachsideoftheenclosureforsurfacewiringconduit.

Fig. 4 Double Harness Lead Connection

 LeadCalciumBatteries

6VoltTopView

6VoltPack

6VoltAnd12VoltPack(2Packs)

12VoltIndividual(2Batteries

Fig. 5 Single Harness Lead Connection

 Nickel-CadmiumBatteries

Fig. 6 Double Harness Lead Connection

 Nickel-CadmiumBatteries

6Volt(1Pack)SmallBattery

6Volt(2Pack)LargeBattery

6Volt(2Pack)SmallBattery

12Volt(4Pack)LargeOrSmallBatteries

Double Sided Tape

LM Series

Hubbell Lighting, Inc. Life Safety Products • www.dual-lite.com

HubbellLighting,Inc.,AllRightsReserved•Specicationssubjecttochangewithoutnotice.•PrintedinU.S.A. 0603225 F 9/08

Summary of content (2 pages)

PAGE 1
Fig. 4 Double Harness Lead Connection Lead Calcium Batteries LM Series Fig. 5 Single Harness Lead Connection Nickel-Cadmium Batteries High-Capacity Emergency Lighting Units Installation Instructions For Standard, Remote Capacity And Damp Location Models Double Sided Tape 6 Volt Top View IMPORTANT SAFEGUARDS 6 Volt (1 Pack) Small Battery When using electrical equipment, basic safety precautions should always be followed including the following. READ AND FOLLOW ALL SAFETY INSTRUCTIONS Fig.
PAGE 2
4. Identify unit as using either: •lead calcium batteries (standard models, i.e. LM30, LMP66) or •nickel cadmium batteries (model number ending with “N”, i.e LM30N, LMP50N-12V) 5. Connect remote lamps (if used) to blue (+, fused) and yellow (–) leads (Fig. 1 or Fig. 2). 6. Connect 120 or 277VAC input connections to transformer (Fig. 1 or Fig. 2). Connect green wire to building ground. Note: insulate the unused transformer lead to prevent potential shock hazard.