Installation Guide

ManualsBrandsDual-Lite ManualsOtherDual-Lite 300-450 Lumens Fluorescent Lighting Emergency Ballast Battery Pack

INSTALLATION INSTRUCTIONS

! IMPORTANT SAFEGUARDS !

WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE

FOLLOWED, INCLUDING THE FOLLOWING:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1. To prevent high voltage from being present on red & yellow output leads prior to installation,

battery connector must be open. Do not join battery connector until installation is complete and

AC power is supplied to the emergency ballast.

2. This product is for use with most 17 W through 40 W single pin or bipin ﬂuorescent lamps, includ-

ing energy saving, circline, U-shaped and rapid-start (4-pin) long compact ﬂuorescent lamps.

3. Make sure all connections are in accordance with the National Electrical Code and any local

regulations.

4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and

battery connector of the emergency ballast before servicing.

5. This emergency ballast is for factory or ﬁeld installation in either the ballast channel or on top of

the ﬁxture.

6. This product is suitable for damp locations where the ambient temperature is 0°C minimum,

+55°C maximum. Product is not suitable for heated air outlets and wet or hazardous locations.

7. An unswitched AC power source is required (120 or 277 VAC, 60 Hz).

8. Do not install near gas or electric heaters.

9. Do not attempt to service the battery. A sealed, no-maintenance battery is used that is not ﬁeld

replaceable. Contact the manufacturer for information on service.

10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe

condition.

11. Do not use this product for other than intended use.

12. Servicing should be performed by qualiﬁed service personnel.

SAVE THESE INSTRUCTIONS

11/21/08

Ni - Cd

CONTAINS NICKEL-CADMIUM

RECHARGEABLE BATTERY.

MUST BE RECYCLED OR

DISPOSED OF PROPERLY.

WARNING – This product contains chemicals known to the State of California to cause cancer, birth defects and/or other

reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.

UFO-3AW

Hubbell Lighting, Inc. • 701 Millennium Blvd • Greenville, SC 29607 • (864) 678-1000 • FAX (864) 678-1415 • www.dual-lite.com

71000016

Summary of content (4 pages)

PAGE 1
UFO-3AW INSTALLATION INSTRUCTIONS ! IMPORTANT SAFEGUARDS ! WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. To prevent high voltage from being present on red & yellow output leads prior to installation, battery connector must be open. Do not join battery connector until installation is complete and AC power is supplied to the emergency ballast. 2.
PAGE 2
INSTALLATION WARNING: TO PREVENT HIGH VOLTAGE from being present ON RED & YELLOW OUTPUT LEADS PRIOR TO INSTALLATION, battery CONNECTOR MUST BE OPEN. do not JOIN battery CONNECTOr until INSTALLATION is complete and Ac power is supplied to the emergency ballast. NOTE: Make sure the necessary branch circuit wiring is available. An unswitched source of power is required. The emergency ballast must be fed from the same branch circuit as the AC ballast. 1. Disconnect AC power from the fixture.
PAGE 3
ILLUSTRATION 5 troffer style fixture strip style fixture Fixture Fixture Charging Indicator Light Charging Indicator Light Violet (+) Violet (+) Brown (–) Brown (–) 5/8" Black Bushing 1/2" White Bushing 1/2" White Bushing 5/8" Black Bushing 1/2" Punch NOTE: After installing the charging indicator light and test switch, mark each with the appropriate label. 6. After installation is complete, supply AC power to the emergency ballast and join the inverter connector. 7.
PAGE 4
EMERGENCY BALLAST AND AC BALLAST MUST BE FED FROM THE SAME BRANCH CIRCUIT. TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLASTS. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS.