DT 400 USB V1_10-14 DUAL DT 400 USB Vollautomatik-Plattenspieler mit USB-Anschluss Bedienungsanleitung
Das Vorwort Diese Bedienungsanleitung hilft Ihnen beim bestimmungsgemäßen und sicheren Gebrauch Ihres Plattenspielers DT 400 USB, im folgenden Plattenspieler oder Gerät genannt. Beachten Sie die Audacity-Software auf der CD sowie die Hinweise zur Verwendung des USB-Anschlusses auf S. 17. Die Zielgruppe dieser Bedienungsanleitung Die Gestaltungsmerkmale dieser Bedienungsanleitung Verschiedene Elemente der Bedienungsanleitung sind mit festgelegten Gestaltungsmerkmalen versehen.
Inhaltsverzeichnis Sicherheit und Aufstellen des Plattenspielers ........... 4 Sicherheit ........................................................................ 4 Aufstellen ........................................................................ 6 Die Gerätebeschreibung............................................... 8 Der Lieferumfang ............................................................ 8 Die besonderen Eigenschaften .......................................
Sicherheit und Aufstellen des Plattenspielers Sicherheit und Aufstellen des Plattenspielers Lesen Sie bitte alle Sicherheitshinweise sorgfältig durch und bewahren Sie diese für spätere Fragen auf. Befolgen Sie immer alle Warnungen und Hinweise in dieser Bedienungsanleitung und auf der Rückseite des Geräts. Sicherheit 4 Das Gerät darf nur an eine Netzspannung von 230 V~, 50 Hz angeschlossen werden. Versuchen Sie niemals, das Gerät mit einer anderen Spannung zu betreiben.
Sicherheit und Aufstellen des Plattenspielers Stellen Sie keine Behälter mit Flüssigkeit, z.B. Blumenvasen, auf das Gerät. Diese könnten umfallen, und die auslaufende Flüssigkeit kann zu erheblicher Beschädigung bzw. zum Risiko eines elektrischen Schlages führen. Der Standort darf nicht in Räumen mit hoher Luftfeuchtigkeit, z.B. Küche oder Sauna, gewählt werden, da Niederschläge von Kondenswasser zur Beschädigung des Gerätes führen können.
Sicherheit und Aufstellen des Plattenspielers Beschädigte Geräte bzw. beschädigte Zubehörteile dürfen nicht mehr verwendet werden. Zur Reinigung des Gerätes und der Schallplatten dürfen nur dafür vorgesehene Reinigungsmittel (antistatisch) verwendet werden. Diese sind im Zubehörfachhandel erhältlich. Aufstellen Der Plattenspieler darf nur auf einer festen horizontalen, vibrationsfreien Fläche aufgestellt werden. Stellen Sie das Gerät nicht in der Nähe von Wärmequellen wie Heizkörpern auf.
Sicherheit und Aufstellen des Plattenspielers Bestimmungsgemäßer Gebrauch Das Gerät dient zum Abspielen und Digitalisieren von Schallplatten. Das Gerät ist für den privaten Gebrauch konzipiert und nicht für gewerbliche Zwecke geeignet. Jede andere Verwendung gilt als nicht bestimmungsgemäß und kann zu Sach- oder sogar zu Personenschäden führen. Der Hersteller übernimmt keine Haftung für Schäden, die durch nicht bestimmungsgemäßen Gebrauch entstanden sind.
Die Gerätebeschreibung Die Gerätebeschreibung Die besonderen Eigenschaften Der Lieferumfang Entnehmen Sie das Gerät und alle Zubehörteile aus der Verpackung. Hinweis: Die Kleinteile befinden sich in den Seiten der Styroporverpackung! Heben Sie den Karton und das Verpackungsmaterial auf, um das Gerät bei einem späteren Transport sicher wieder verpacken zu können.
Die Gerätebeschreibung Die Bedienelemente 18 17 16 19 1 15 2 13 3 9 4 11 10 14 12 8 7 6 5 9
Die Gerätebeschreibung 1 Ablage Zentrierpuck (Adapter für 7“ EP’s) 14 Gegengewicht 2 Plattenteller mit Plattentellerbelag 15 PHONO/LINE-Umschalter 3 Plattentellerachse 16 4 Taste Drehzahl (SPEED 33/45) Cinch-Audio-Kabel (mit Stecker weiß und rot); rot - rechter Kanal, weiß - linker Kanal 5 Taste-Start (START) 17 USB-Anschluss, max.
Wie Sie den Plattenspieler zum Betrieb vorbereiten Wie Sie den Plattenspieler zum Betrieb vorbereiten Plattentellerbelag Riemen und Plattenteller Zentrierpuck Der Antriebsriemen liegt bei Lieferung bereits auf der Riemenlauffläche des Plattentellers auf. Der Riemen ist mit einem roten Band versehen, mit dem der Riemen um die Antriebsachse des Motors (Pully) gezogen wird. Den Plattenteller auf die Plattentellerachse aufsetzen.
Wie Sie den Plattenspieler zum Betrieb vorbereiten Tonarmkopf montieren Montieren Sie den Tonarmkopf 1 wie dargestellt auf die Aufnahme des Tonarms 3. 1 3 Gegengewicht anbringen Das Gegengewicht 2 wird wie dargestellt auf den Tonarm 1 geschraubt. 2 Sichern Sie den Tonarmkopf auf dem Tonarm, indem Sie den Schraubring 2 wie abgebildet drehen, während Sie den Tonarmkopf waagrecht halten.
Wie Sie den Plattenspieler zum Betrieb vorbereiten Einstellen der Auflagekraft Halten Sie das Gegengewicht mit einer Hand fest und drehen Sie nur den Gegengewicht-Einstellring, bis dessen “0’‘-Marke auf 12-Uhr zeigt (nach oben). Drehen Sie nun das Gegengewicht im Gegenuhrzeigersinn (nach links) und stellen Sie das korrekte Auflagegewicht ein. Der Auflagedruck kann direkt am Skalaring abgelesen werden.
Anschluss des Plattenspielers Anschluss des Plattenspielers Mischpult Schalter PHONO/LINE: 1 – auf LINE 2 – auf PHONO 1 3 14 2 3 – USB-Anschluss an PC
Anschluss des Plattenspielers Anschluss an den Verstärker Schließen Sie die Cinch-Audiokabel 16 an die LINE/AUX- oder Phono-Buchsen am Verstärker an. Hinweis: Dabei auf den richtigen Anschluss des linken und rechten Kanals achten (rot = rechter Kanal, weiß = linker Kanal). Abnehmen/Anbringen der Nadelschutzkappe Vor der Wiedergabe einer Schallplatte muss die Nadelschutzkappe vom Tonabnehmer entfernt werden. Ziehen sie die Kappe nach vorne ab.
Abspielen einer Schallplatte Abspielen einer Schallplatte Automatischer Start Platte auflegen. Ggf. bei Singles Zentrierpuck 1 aufsetzen. Ggf. den Nadelschutz entfernen. Mit dem Wahlhebel 7 die entsprechende Plattengröße von 30 oder 17 cm Durchmesser einstellen. Mit der Taste-Drehzahl SPEED 4 die Plattentellerdrehzahl 33 oder 45 U/min einstellen. Taste START 5 drücken. Der Plattenteller beginnt, sich in der voreingestellten Geschwindigkeit zu drehen.
Bevor Sie den USB-Anschluss herstellen Bevor Sie den USB-Anschluss herstellen Systemvoraussetzungen Hinweis: Die mitgelieferte Software Audacity® vor der Verbindung und Inbetriebnahme des Gerätes am PC bzw. MAC installieren. Die Audacity®-Software ist eine freie Open-SourceSoftware verbreitet unter der GNU General Public License (GPL). Sehen Sie bitte auf der Homepage nach, ob ein Update verfügbar ist. Unter http://audacity.sourceforge.net steht ggf. eine aktuelle Version bzw.
Wie Sie Ihre Musik digitalisieren Wie Sie Ihre Musik digitalisieren Software installieren Starten Sie Ihren Rechner, legen Sie die CD ein und installieren Sie die Audacity-Software je nach Betriebssystem (PC, MAC). Sehen Sie bitte auf der Homepage nach, ob ein Update verfügbar ist (http://audacity.sourceforge.net) und installieren Sie ggf. das Update. Hinweis: Eine ausführliche Anleitung zur Software Audacity finden Sie auch auf der Software-CD.
Wie Sie Ihre Musik digitalisieren Musik aufzeichnen und speichern 1. Starten Sie die Wiedergabe am Plattenspieler. 2. Klicken Sie auf die rote Aufnahme-Taste in der Software. 3. Klicken Sie auf die blaue PAUSE-Taste zum vorübergehenden Unterbrechen der Aufnahme. 4. Klicken Sie zum Beenden der Aufzeichnung auf die gelbe STOP-Taste. 5. Klicken Sie auf die grüne PLAY-Taste zur Wiedergabe Ihrer beendeten Aufzeichnung. 6.
Den Plattenspieler reinigen Den Plattenspieler reinigen Stromschlag Um die Gefahr eines elektrischen Schlags zu vermeiden, dürfen Sie das Gerät nicht mit einem nassen Tuch oder unter fließendem Wasser reinigen. ACHTUNG! Sie dürfen keine Scheuerschwämme, Scheuerpulver und Lösungsmittel wie Alkohol oder Benzin verwenden. Zur Reinigung des Gerätes und der Schallplatten dürfen nur dafür vorgesehene Reinigungsmittel (antistatisch) verwendet werden. Diese sind im Zubehörfachhandel erhältlich.
Wie Sie Fehler beseitigen Wie Sie Fehler beseitigen Wenn das Gerät nicht wie vorgesehen funktioniert, überprüfen Sie es anhand der folgenden Tabellen. Wenn Sie die Störung auch nach den beschriebenen Überprüfungen nicht beheben können, nehmen Sie bitte Kontakt mit dem Hersteller auf. Probleme mit dem Gerät Symptom Mögliche Ursache/Abhilfe Der Tonarm überspringt Spuren, gleitet über die Platte oder bewegt sich nicht Der Plattenspieler steht nicht waagerecht.
Technische Daten Technische Daten Abmessungen (Breite x Höhe x Tiefe): 435 mm x 121,5 mm x 372 mm Gewicht: 3,9 kg Spannung: 230 V Wechselstrom, 50 Hz Leistungsaufnahme: 2W Umgebungsbedingungen: +5 °C bis +35 °C 45 % bis 85 % relative Luftfeuchte (nicht kondensierend) Abtastnadel: Diamant-Nadel System: Magnetisches System WOW, Flutter < 0.25% WRMS (JIS WTD), 3 kHz 1/3 bei 33 Upm USB-Anschluss USB 1.1 für WINDOWS, MAC OSX Frequenzgang 20 Hz ...
Wie Sie den Hersteller erreichen Wie Sie den Hersteller erreichen DGC GmbH Graf-Zeppelin-Str. 7 D-86899 Landsberg www.dual.de Entsorgungshinweise Entsorgung der Verpackung Ihr neues Gerät wurde auf dem Weg zu Ihnen durch die Verpackung geschützt. Alle eingesetzten Materialien sind umweltverträglich und wieder verwertbar. Bitte helfen Sie mit und entsorgen Sie die Verpackung umweltgerecht. Über aktuelle Entsorgungswege informieren Sie sich bei Ihrem Händler oder über Ihre kommunale Entsorgungseinrichtung.