DUAL CS 329 BEDIENUNGSANLEITUNG OWNERS MANUAL DE: SEITE 2 – 11 EN: PAGE 12 – 22 BDA CS 329 V1 DE EN
Contents Page Contents 12 Technical specifications 13 Preface 14 14 14 14 14 Intended users of this operating manual Warnings Directives Disposal Safety instructions Safety Intended use 15 15 15 List of contents / Packing instructions 16 Product overview 17 Set Up 18 18 18 18 18 19 Platter and belt installation Tonearm Dust cover fitting Connection to power supply Connection to amplifier Operating the turntable Removing / Attaching the stylus protection cap To play the record (manually) To
Technical Specifications Motor Drive Speed settings Wow & Flutter Belt / DC Motor 33/45 < ±0,12 % (DIN WTD) Tonearm Function Bearing Fully automatic or manually operated Ball-bearing Effective length Offset Angle Overhang Type Stylus Pressure Range Factory installed Pick-up Replacement Stylus 221,5 mm 25,6° 19 mm statically balanced, fixed setting 1,8 g +/- 0,3 g Audio-Technica AT91 Audio-Technica ATN91 Platter Material Mat Bearing Diameter Weight incl.
Preface This instruction manual will help you to operate the turntable in a safe way. Please read this manual and the safety notices carefully before using the unit and keep them for later use. Be sure to make them accessible to other users and observe all information given here. Intended users of this operating manual This operating manual is intended for everyone who: • sets up, • operates, • cleans • or disposes of the record player.
Safety instructions Please read through all of the safety instructions carefully and keep them for questions that may arise later. Always observe all warnings and instructions in this operating manual and on the rear of the unit. Safety instructions for using the power supply • The unit should only be connected to a mains voltage supply of 100- 240 V~, 50/60 Hz. • Never try to operate the unit with a different voltage. • Only use the supplied power supply or an original Dual alternative.
List of contents / Packing instructions Unpacking 1) 2) 3) First, remove the appliance and all associated parts from the packaging. Remove all adhesive tapes. Ensure that all listed components are present: Note: • • • The small components are in the side compartments of the polystyrene packaging sections! Do not throw the stylus guard for the needle away! Retain the packaging for any possible future transportation! List of contents 1. 2. 3. 4. 5. 6. 7. 8.
Product overview 1 2 3 13 4 12 15 14 11 5 10 9 16 17 6 7 8 Nr Description 1 Dust cover hinges (2×) 2 Platter 3 Platter mat 4 Platter bearing 5 Speed selector 33, 45 6 PHONO / LINE Switch Phono-preamp on-/off 7 RCA-Cable-Output red - right channel, white - left channel 8 DC IN: 12 V-Input for Power supply 9 Start button 10 Stop button 11 Lever record size 12 Tonearm 13 Tonearm lift 14 Tonearm rest 15 Tonearm lift lever 16 Tonearm 17 Headshell 17, 30 17
Set Up Platter and belt installation Tape Motorpully The record player is delivered with the drive belt already fitted around the platter flange. The belt is provided with a red tape so that it can be pulled over the drive motor pulley. (pic. 1) 1. 2. 3. Place the platter on the turntable spindle. Rotate the platter until the cut-out is positioned over the motor pulley (at about the 8 o'clock position).
Set Up Connection to Amplifier The turntable comes with a built-in phono pre-amplifier. It can be either connected to the phono input or the line input at the amplifier. The built-in phono stage can switched on or off via a switch in the back of the turntable. Phono-Input 1. 2. 3. 1 Connect the RCA cable to the Audio output „AUDIO OUT” (2) at the turntable and the PHONO input sockets at the amplifier. Move the switch (1) into the position: PHONO.
Operating the turntable Removing / Attaching the stylus protection cap Pic. 1 Remove the stylus protection cap from the pick-up prior to playing a record. (Pic.1) 1. Pull the cover from the stylus on the bottom (B) as seen in the diagram. 2. Replace the cap after playing the record. Stylus Cover To play the record (manually) 1. Place a record on the turntable; use the spindle adaptor to play singles. 2. Push the speed button for the required setting: 33, 45. 3. Raise the tonearm with the lift lever.
Cleaning & Troubleshooting Cleaning stylus and record Clean the stylus and record prior to every record played. That minimises premature wear and tear. Damage to components! 1. Carefully wipe the stylus brush in a front to back motion under the stylus. 2. To clean a record, use a carbon fibre brush to wipe gently and diagonally over the record. Note: Brushes and accessories are available in the Dual shop: www.dual.
Dual GmbH www.dual.eu support@dual.