SG3/SG4/SG5 INSTALLATl ON/OWNER'S MANUAL Universal Marine Splash Guard
• • SG3/SG4/SG5 INSTALLATION -Preparation Protect your marine head unit from damage and the harsh marine environment with the SG3/SG4/SG5 splash guard. This marine grade cover fits most single DIN size head units and will protect against splashes and debris. Before You Start • Disconnect negative battery terminal. Consult a qualified marine technician or service manual for instructions. • Due to differences in head units.
SG3/SG4/SG5 INSTALLATION m Mounting Mounting • Open splashguard and detach side covers by pulling outward from the inside of side cover. • Insert supplied mounting bolts through washers and into mounting holes as shown below. • Place gasket between back side of splash guard and mounting surface and secure the splash guard in place with supplied nuts. • Install head unit into splash guard opening. This may vary depending on head unit manufacturer and installation instructions.
• SG3/SG4/SG5 WARRANTY Limited One Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase. Dual Electronics Corp. agrees. at our option. during the warranty period. to repair any defect in material or workmanship or to furnish an equal new.
DMP672/DMP672B INSTALLATION/OWNER'S MANUAL 6.
• DMP672/DMP672B INSTALLATION Prepa ration/Installation Please read entire manual before installation. Before You Start • Disconnect negative battery terminal. Consult a qualified technician for instructions. • Use extreme caution when drilling holes to avoid damaging fuel lines, hydraulic lines or existing wiring. • If additional wiring is required: we recommend that you run all wires prior to mounting your speaker in place.
DMP672/DMP672B WARRANTY • Limited One Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase. What to do? 1. Before you call for service. check the troubleshooting guide in your owner's manual.
• DMP672/DMP672B SPECIFICATIONS Specifications Outside Diameter 7.13" Mounting Depth 2.13" Mounting Height .87" Cut-out Diameter 5.13" Frequency Response 45Hz-15kHz Sensitivity 88dB 1W/1M Impedance 4ohms RMS Power 20 Watts @ 1kHz Peak Power 100 Watts @ 1kHz Design and specifications subject to change without notice. Dual Electronics Corp. Toll Free: 1·866-382-5476 9AM-5PM EST. Monday-Friday www.dualav.com <02015 Dual Electronics Corp. All rights reserved.
I Quick Start Guide For Mechless and CD Receivers Not all features listed in this QSG are available on all models. • • • •• • • • • • •• • ••• To download the complete, model-specific manual, please visit www.dualav.com/support/manuals.php or call 1-866-382-5476, 9AM-5PM EST (Monday-Friday).
Installation Before You Start • Consult a qualified technician for instructions. Dual always recommends professional installation. • Disconnect negative battery terminal. • Remove trim ring from unit (if installed). • Remove 2 transit screws located on top of the unit (if applicable). • Insert the removal keys. and remove the mounting sleeve from the head unit. Note: Most vehicles require an installation kit.
Installation Der:bw ■rd Mounting the Head Unit: Typical DIN mounting Step 1: Insert the mounting sleeve into the installation kit or dashboard. Step 2: Bend multiple mounting tabs around the mounting sleeve until the mounting sleeve is secure. 0 . ,. . . . 4_. ls Step 3: Conned all wiring harnesses and slide the head unit into the mounting sleeve until it clicks into place. Mounting the Head Unit: ISO mounting Using the existing brackets or the brackets supplied with the installation kit.
General Operation Power On/Off Faceplate Removal Changing Modes Volume Mute Press the
AM/FM Tuner Operation Seek Tuning Manual Tuning Band Press TUNE ◄◄ or TUNE ►► for more than one second to seek to the next strong station. Press TUNE ◄◄ or TUNE ►► momentarily to move radio frequency up or down one step at a time. Press and hold to advance quickly. Press BAND to select between FM1. FM2. FM3. AM1 and AM2 bands. Up to six presets can be programmed for each band. enabling up to 18 FM stations and 12 AM stations to be stored in memory.
CD Operation• Insert CD With the label facing up, insert a standard size CD into the CD slot. Playback will begin automatically. Eject CD Press EJECT (located behind the front panel) to eject the CD. The unit will change to previous mode of operation. Track Select Press TUNE ►► to skip to the beginning of the next track. Press TUNE ◄◄ to return to the beginning of the current track. Pressing TUNE ◄◄ again skips to the beginning of the previous track. Fast Forward/ Reverse Press and hold 1\JNE ►► or T
MP3 / WMA Operation * Playing MP3/WMA Files Track Select Fast Forward and Reverse Pause To play MP3/WMA files. insert a data CD. SD card or USB device containing MP3/WMA files. Press 'TUNE ►► to skip to the beginning of the next song. Press 'TUNE ◄◄ to return to the beginning of the current song. Pressing nJNE ◄◄ again skips to the beginning of the previous song. Press and hold TUNE ►► or TUNE ◄◄ to fast forward or reverse a track. Press ►/ II to temporarily stop playback.
Operation of iPod/iPhone* Connect an iPod/ iPhone Device (sold separately) Song Select Forward/Reverse Pause Repeat To play music from an iPod/iPhone device. connect the USB cable (included with your iPod/iPhone device) to the unit's USB port. Playback will begin automatically. Press ►► to skip to the next song. Press ◄◄ to return to the beginning of the current song. Pressing ◄◄ again skips to the beginning of the previous song. Press and hold ►► or ◄◄ to fast forward or reverse.
Bluetooth® Operation* Preparation Before using a Bluetooth device. it must be paired and connected. Ensure that Bluetooth is activated on your device before beginning the pairing process. Pairing a New Device The head unit broadcasts the pairing signal constantly when no devices are connected. Complete the pairing sequence from your Bluetooth device. Refer to the owner's manual for your device for more details.
Pandora® Operation* Requirements Control for Pandora requires: • An iPhone device with a reliable data connection, or an iPod touch that is connected to wireless internet. • ·The Pandora App installed on the iPhone/iPod device. • An active account with Pandora (www.pandora.com). • The USB sync cable included with iPod/iPhone device. use Connection Connect an iPod touch or iPhone device (required, sold separtely) to the USB port, using the USB sync cable included w ith your iPhone device.
Limited One-Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase. (Note that select marine products carry a 2-year warranty. Please visit www.dualav.com for details.) Dual Electronics Corp. agrees. at our option. during the warranty period.
FCC -Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1 ) this device may not cause harmful interference. and (2) this device must accept any interference received. including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
