MXD40 INSTALLATION/OWNERS MANUAL AM/FM/CD Marine Receiver with Detach Face MARINE
MXD40 INSTALLATION Preparation Please read entire manual before installation. Before You Start • Disconnect negative battery terminal. (consult a qualified technician for instructions) • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started • Remove 2 transit screws located on top of the unit.
MXD40 INSTALLATION Wiring Diagram Antenna Connector RCA Cable (sold separately) GRAY Rear Preamp Output Connect to amplifier RCA Input BLUE Remote Turn-On Connect to amplifier or power antenna. Insulate wire if not used. AMP BLACK Ground 5 AMP AGC Fuse Connect to chassis ground. YELLOW Memory Connect to battery circuit or constant 12 volt source. 0.5 AMP AGC Fuse FUSES RED Accessory Connect to existing ignition circuit or switched 12 volt source.
MXD40 OPERATION Control Locations 1 2 3 18 17 16 15 14 13 12 11 4 5 6 10 9 8 1 Release 10 Preset 6 2 Volume 11 Preset 5 3 Tune/Track Up 12 Preset 4/CD Random 4 Band 13 Preset 3/CD Repeat 5 Bass Boost 14 Preset 2/CD Intro 6 Eject 15 Preset 1/CD Top 7 Display 16 Audio 8 Play/Pause 17 Power 9 Auto Store/Preset Scan 18 Tune/Track Down 7 MARINE The MXD40 Marine Receiver features UV resistant faceplate construction and clear-coated circuit boards for long las
MXD40 OPERATION General Operation Faceplate Removal Press REL and pull away from the left side to remove. To re-install, insert right side of faceplate first then push left side to secure. *For semi-permanent faceplate installation, remove trim ring and install supplied Phillips head #1 screw through left side of mounting frame into faceplate. Power On/Off CD Mode Press PWR to turn the unit on. Inserting a CD will turn the unit on automatically. Press PWR to turn the unit off.
MXD40 OPERATION General Operation 6 Reset Press and hold for more than 2 seconds to RESET the unit upon initial installation. The RESET button is located behind the faceplate. Audio Press AUD to select between Volume (default), Bass, Treble, Balance & Fader.
MXD40 OPERATION Tuner Operation Seek Tuning Manual Tuning Band Press TUNE strong station. or momentarily to seek the next or for more than 2 seconds, then Press TUNE press TUNE or momentarily to move radio frequency up or down one step at a time. Press and hold to advance quickly. If tuning is not adjusted for 2 seconds, the unit will return to seek tuning mode (default). Press BAND to select between FM1, FM2, FM3 and AM1, AM2 bands.
MXD40 OPERATION CD Player Operation Insert CD Eject CD Track Select Fast Forward and Reverse Pause Intro Repeat Random Top CD-R Compatibility 8 With the label facing up, insert a standard 5" CD into the CD slot. The CD will automatically begin playback. Press the EJECT button to stop and eject the CD. The unit will change to tuner mode. Press TRACK to skip to the beginning of the next track. Press TRACK to return to the beginning of the current track.
MXD40 WARRANTY Limited One-Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Namsung America Inc. warrants this product to the original purchaser to be free from defects in material and workmanship, under normal conditions, for a period of one year from the date of the original purchase.
MXD40 OPERATION Specifications CD Player Signal-to-noise: >86dB Frequency response: 20Hz-20kHz, ±3dB Channel separation @ 1kHz: >65dB D/A converter: 16 Bit FM Tuner Tuning range: 87.5MHz-107.9MHz FM mono sensitivity: 12dBf 50dB quieting sensitivity (stereo): 16dBf Stereo separation @ 1kHz: 40dB Frequency response: 30Hz-13kHz, ±3dB AM Tuner Tuning range: 530kHz-1710kHz AM sensitivity: 30uV Frequency response: 80Hz-2kHz, ±3dB General Total system power: 100 Watts Peak Power output: 25Wx4 @ 14.
MXD40 OPERATION Troubleshooting Problem Cause Unit will not turn on (no power) Yellow wire not connected or incorrect voltage Red wire not connected or incorrect voltage Black wire not connected Fuse blown Speaker wires not connected One or more speaker wires touching each other or touching chassis ground Yellow or red wire touching chassis ground Speaker wires touching chassis ground Incorrect fuse rating Unit is not mounted correctly or backstrap is not secure Physical defect in media (CD or CD-R) Hig
Namsung America Inc. 21318 64th Ave. South Kent, WA 98032 Toll Free: 1-866-626-7863 ©2003 Namsung America, Inc.
DMP65 INSTALLATION/OWNERS MANUAL 6.
DMP65 INSTALLATION Preparation/Installation Please read entire manual before installation. Before You Start • Disconnect negative battery terminal. (consult a qualified technician for instructions) • Use extreme caution when drilling holes to avoid damaging fuel lines, hydraulic lines or existing wiring. Getting Started • Determine where the speakers will be mounted. Ensure an area large enough for the speaker to mount evenly. Be sure the mounting location is deep enough for the speaker to fit.
DMP65 WARRANTY Limited One-Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Namsung America Inc. warrants this product to the original purchaser to be free from defects in material and workmanship, under normal conditions, for a period of one year from the date of the original purchase.
DMP65 SPECIFICATIONS Specifications Outside Diameter 7.13" Mounting Depth 2.5" Mounting Height .88" Cut-out Diameter 5.13" Frequency Response Sensitivity 45Hz-18kHz, ±3dB 90dB 1W/1M Impedance 4 ohms RMS Power 20 Watts Peak Power 60 Watts Specifications subject to change without notice Namsung America Inc. 21318 64th Ave. South Kent, WA 98032 Toll Free: 1-866-626-7863 ©2003 Namsung America, Inc.