XD6320 INSTALLATION/OWNERS MANUAL AM/FM/CD Receiver with Detach Face
XD6320 INSTALLATION Preparation Please read entire manual before installation. Before You Start • Disconnect negative battery terminal. (consult a qualified technician for instructions) • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started • Remove 2 transit screws located on top of the unit.
XD6320 INSTALLATION Wiring Diagram FUSE When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The XD6320 uses one 10 amp ATM fuse located beside the wiring connector.
XD6320 OPERATION Control Locations 1 22 4 3 2 21 20 19 4 18 17 16 15 6 7 8 13 12 11 5 14 1 Release 12 Tuner Scan 2 Power 13 Local/Distance 3 Volume 14 Preset 6 4 Band/Play/Pause 15 Preset 5 5 Mode 16 Preset 4 6 Auto Store/Preset Scan 17 Preset 3/Intro 7 Tune/Track Down 18 Preset 2/Random 8 Eject 19 Preset 1/Repeat 9 Tune/Track Up 20 Audio 10 Display 21 Loudness 11 EQ 22 Mute 9 10
XD6320 OPERATION General Operation Faceplate Removal Semi-permanent Faceplate Installation Power On/Off Mode Loudness Volume Press RELEASE and pull away from the left side to remove. To re-install, insert right side of faceplate first then push left side to secure. Remove trim ring and install supplied #1 x 7/32” Phillips head screw through left side of mounting frame into faceplate. Press POWER or any other button (except eject) to turn the unit on.
XD6320 OPERATION General Operation 12/24-hour Clock Programmable Display Priority The clock will display 12-hour AM/PM time in USA frequency spacing mode (PM 10:00). In European frequency spacing mode, the clock will display 24-hour time (22:00). In tuner mode, press and hold DISP then press TUNE to select function priority display. “FREQ” will momentarily appear in the display. ll Note: "FUNC" will appear in CD or AUX modes.
XD6320 OPERATION General Operation Audio Press AUDIO to select between Volume (default), Bass, Treble, Balance & Fader.
XD6320 OPERATION Tuner Operation Seek Tuning Manual Tuning Press TUNE or TUNE next strong station. nn Press TUNE or TUNE for more than 2 seconds, then release. "MANUAL" will momentarily appear in the display. Press TUNE or TUNE momentarily to move radio frequency up or down one step at a time. Press and hold to advance quickly. If tuning is not adjusted for 5 seconds, the unit will return to seek tuning mode (default). "AUTO" will momentarily appear in the display.
XD6320 OPERATION CD Player Operation Insert CD With the label facing up, insert a standard size CD into the CD slot. The CD will automatically begin playback. Eject CD Press EJECT to eject the CD. The unit will change to previous mode of operation (AM, FM, or auxiliary input). If the disc is not removed within 10 seconds, the unit will reload the disc. The unit does not have to be turned on to eject CD. Track Select Press TRACK to skip to the beginning of the next track.
XD6320 WARRANTY Limited One-Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship, under normal conditions, for a period of one year from the date of the original purchase. Dual Electronics Corp.
XD6320 OPERATION Specifications CD Player Signal-to-noise: >92dB Frequency response: 10Hz-20kHz Channel separation @ 1kHz: >65dB D/A converter: 1 Bit FM Tuner Tuning range: 87.5MHz-107.9MHz Usable sensitivity: 8.5dBf 50dB quieting sensitivity: 10dBf Stereo separation @ 1kHz: 40dB Frequency response: 30Hz-13kHz AM Tuner Tuning range: 530kHz-1710kHz Usable sensitivity: 22uV Frequency response: 30Hz-2.2kHz General Total power output: 200 Watts Peak Power output: 50Wx4 @ 4 ohms, 14.
XD6320 WARRANTY Troubleshooting Problem Cause Unit will not turn on (no power) Yellow wire not connected or incorrect voltage Red wire not connected or incorrect voltage Black wire not connected Fuse blown Check connections for proper voltage (11~16VDC) Check connection to ground Replace fuse Unit has power (but no sound) Speaker wires not connected One or more speaker wires touching each other or touching chassis ground Yellow or red wire touching chassis ground Speaker wires touching chassis ground