XDM260 INSTALLATION/OWNER'S MANUAL AM/FM/CD Receiver with Detachable Face
XDM260 INSTALLATION Preparation Please read entire manual before installation. Before You Start • Disconnect negative battery terminal. Consult a qualified technician for instructions. • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started • Remove trim ring from unit. • Remove 2 transit screws located on top of the unit.
XDM260 INSTALLATION Wiring Diagram Antenna Connector Rear Preamp Output Connect to amplifier RCA input L-CH R-CH RCA Cable (sold separately) BLUE BLACK RED Remote Turn-On Connect to amplifier or power antenna. Insulate wire if not used. AMP Ground Connect to vehicle chassis ground. Accessory Connect to ignition circuit or switched 12 volt source. 5 AMP AGC Fuse YELLOW Memory Connect to battery circuit or constant 12 volt source.
XDM260 OPERATION Control Locations - Receiver 1 19 4 2 18 3 17 4 5 16 15 14 13 12 11 10 9 8 1 Release 11 Preset 3 / Intro 2 Band / Go Back 12 Preset 2 / Random 3 Volume Knob 13 Preset 1 / Repeat 4 Power 14 Display 5 Eject 15 Tune / Track Up 6 USB Port 16 Tune / Track Down 7 Auxiliary Input 17 Mode 8 Preset 6 / Folder Up 18 Audio / Menu 9 Preset 5 / Folder Down 19 Mute 10 Preset 4 / Play / Pause 6 7
XDM260 INSTALLATION General Operation Faceplate Removal Press RELEASE and pull away from the left side to remove. To re-install, insert right side of faceplate first then push left side to secure. Power On/Off Press or any other button (except EJECT) to turn the unit on. Press to turn the unit off. Mode Press MODE to select between AM/FM, CD player, auxiliary, USB. Modes of operation are shown in the display. NOTE: CD and USB modes will not appear unless a CD is inserted or USB device is connected.
XDM260 OPERATION General Operation - Setup Menu Menu Function Auto Station Store Local/Distance Tuning Tuner Frequency Spacing Auxiliary Input Beep Confirmation Options Action AUTO STORE Press SELECT to seek and save 6 strong stations in the current band. (Tuner mode only) Activates distance tuning (Tuner mode only). Activates local tuning for strong station reception only (Tuner mode only). Programs the unit to USA tuner spacing. (200kHz for FM and 10kHz for AM).
XDM260 INSTALLATION General Operation Audio Press AUDIO/MENU momentarily to select between Bass, Treble, Balance and Fader. BASS Bass Treble Balance Fader TREBLE BALANCEE SOURCE LEVEL LOUDNESS FADER EQ Press AUDIO/MENU until BASS appears then rotate volume knob left/right to adjust ( -6 minimum / +6 maximum). Press AUDIO/MENU until TREBLE appears then rotate volume knob left/right to adjust ( -6 minimum / +6 maximum).
XDM260 OPERATION Seek Tuning Manual Tuning Band Storing and Recalling Station Presets 8 AM/FM Tuner Operation Press TUNE nn or TUNE ll momentarily to seek to the next strong station. nn ll Press and hold TUNE or TUNE until "MANUAL" appears, then press TUNE or TUNE momentarily to change radio frequency up or down one step at a time. Press and hold to advance quickly. nn ll Press BAND to select between FM1, FM2, FM3, AM1 and AM2 bands. Up to 18 FM stations and 12 AM stations can be stored.
XDM260 INSTALLATION CD Player Operation Insert CD Eject CD Track Select Fast Forward/Reverse Pause Intro Repeat Random CD-R/CD-RW Compatibility With the label facing up, insert a standard size CD into the CD slot. The CD will automatically begin playback. Press EJECT to eject the CD. The unit will change to previous mode of operation. If the disc is not removed within 10 seconds, the unit will reload the disc. The unit does not have to be turned on to eject CD.
XDM260 OPERATION CD Player Operation - MP3/WMA Files Playing an MP3/WMA CD Displaying Information Character Support When an MP3/WMA encoded disc is first inserted, “LEAD" will appear in the display. Depending on the number of files and folders, this may take several seconds. ID3 tag and file/folder information will be automatically changed during playback. Press DISP to view the clock. Default display will resume after five seconds.
XDM260 INSTALLATION CD Player Operation - MP3/WMA Files Media Compatibility The following types of discs/files are compatible: • CD-ROM (ISO), CD-R, CD-RW • CD-DA • MP3 data • WMA data The following types of discs/files are not compatible: • WMA files that are protected by DRM (Digital Rights Management).
XDM260 OPERATION CD Player Operation - MP3/WMA Files Additional MP3/WMA Information When playing a disc recorded with regular audio files (CD-DA or .WAV) and MP3/WMA files, the unit will play the MP3/WMA files only. Only MP3 files with filename extension (.mp3) can be played. Only WMA files with filename extension (.wma) can be played. Do not attempt to play discs which contain non-MP3/WMA files with the MP3/WMA extension.
XDM260 INSTALLATION USB Operation Connecting a USB Device (sold separately) Playing Music Track Select Fast Forward and Reverse Pause Displaying Information Repeat Random Intro To play MP3/WMA files from most USB mass storage devices, line up the USB connector and insert the USB device into the XDM260's USB port. When a USB device is first connected, “LEAD” will appear in the display and playback will begin momentarily.
XDM260 OPERATION USB Operation Character Support Maximum character display information • Track name – 64 character maximum • Directory name – 64 character maximum • *Song title – 64 character maximum • *Artist name – 64 character maximum • *Album name – 64 character maximum *Song title, artist name and album name will only be displayed if included with the MP3/WMA file.
XDM260 INSTALLATION USB Operation Additional MP3/WMA Information Only MP3 files with filename extension (.mp3) can be played. Only WMA files with filename extension (.wma) can be played. Do not attempt to play non-MP3/WMA files with the MP3/WMA extension.
XDM260 OPERATION Troubleshooting Problem Unit will not turn on (no power) Unit has power (but no sound) Unit blows fuses Excessive skipping ERR FILE appears on display NO FILE appears on display Unit will not accept a disc NO SUPPORT appears on display 16 Cause Action Yellow wire not connected or incorrect voltage Red wire not connected or incorrect voltage Black wire not connected Fuse blown Speaker wires not connected Check connections for proper voltage (11~16VDC) One or more speaker wires to
XDM260 INSTALLATION Limited One Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase. Dual Electronics Corp.
XDM260 OPERATION FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
XDM260 INSTALLATION Specifications CD Player Frequency response: 20Hz-20kHz Channel separation @ 1kHz: >60dB D/A converter: 1 Bit FM Tuner Tuning range: 87.5MHz-107.9MHz Usable sensitivity: 8.5dBf 50dB quieting sensitivity: 10dBf Stereo separation @ 1kHz: >30dB Frequency response: 30Hz-13kHz AM Tuner Tuning range: 530kHz-1710kHz Usable sensitivity: <42dBu Frequency response: 30Hz-2.
Dual Electronics Corp. Toll Free: 1-866-382-5476 9AM-5PM EST, Monday-Friday www.dualav.com ©2013 Dual Electronics Corp. All rights reserved. Other trademarks and trade names are those of their respective owners.