Owner’s manual DUCATI998S Bostrom 1
Hearty welcome among Ducati fans! Please accept our best compliments for choosing a Ducati motorcycle. We think you will ride your Ducati motorcycle for long journeys as well as short daily trips. Ducati Motor Holding S.p.A. wishes you smooth and enjoyable riding. We are steadily doing our best to improve our “Technical Assistance” service. For this reason, we recommend you to strictly follow the indications given in this manual, especially for motorcycle running-in.
TABLE OF CONTENTS General 6 Warranty 6 Symbols 6 Useful information for safe riding 7 Carrying the maximun load allowed 8 Accessories 8 Identification data 9 Controls 10 Position of motorcycle controls 10 Instrument panel 11 Keys 12 Key-operated ignition switch and steering lock 13 Left switch 14 Clutch lever 15 Starter lever 16 Right switch 17 Throttle twistgrip 17 Front brake lever 17 Rear brake pedal 18 Gear change pedal 18 Adjustment of gear change and rear brake pedals 19 4 Main components and device
Chain tension inspection 48 Chain lubrication 48 Replacing bulbs 49 Beam setting 52 Rear view mirror adjustment 53 Tubeless tyres 53 Checking engine oil level 55 Cleaning and replacing the spark plugs 56 Cleaning the motorcycle 57 Storing the bike away 58 Important notes 58 Technical data 59 Overall dimensions 59 Weights 59 Top-ups 60 Engine 61 Timing system 61 Performance data 62 Spark plugs 62 Performance data 62 Brakes 62 Transmission 63 Frame 64 Wheels 64 Tyres 64 Suspensions 65 Electric system 66 Routi
GENERAL Warranty In your own interest, and in order to guarantee product reliability, you are strongly advised to refer to a Ducati Dealer or Authorized Workshop for any servicing requiring particular technical expertise. Our highly skilled staff have access to the implements required to perform any servicing job at best, using Ducati original spare parts only as the best guarantee for full interchangeability, smooth running and long life. All Ducati motorcycles come with a “Warranty Card”.
Useful information for safe riding Warning Read this section before riding your motorcycle. Accidents are frequently due to inexperience. Always make sure you have your licence with you when riding; you need a valid licence to be entitled to ride your motorcycle. Do not lend your motorcycle to inexperienced riders or who do not hold a valid licence. The rider must always wear a safety helmet.
Carrying the maximum load allowed Your motorcycle is designed for long-distance riding, carrying the maximum load allowed in full safety. Even weight distribution is critical to preserving safety features and avoiding trouble when performing sudden manoeuvres or riding on bumpy roads. Information about carrying capacity The total weight of the motorcycle in running order including rider, luggage and additional accessories should not exceed 310 Kg.
Identification data All Ducati motorcycles have two identification numbers, for frame (fig. 1.1) and engine (fig. 1.2). Frame number Engine number Note These numbers identify the motorcycle model and are required when ordering spare parts. This exclusive model has been produced in a limited series. Each motorcycle is identified by a serial number etched on a silver plate fixed to steering head. fig. 1.1 fig. 1.
CONTROLS Warning This section details the position and function of all the controls you need to drive your motorcycle. Be sure to read this information carefully before you use the controls. Position of motorcycle controls (fig. 2) 1) Instrument panel. 2) Key-operated ignition switch and steering lock. 3) Left switch. 4) Clutch lever. 5) Cold start button. 6) Right switch. 7) Throttle twistgrip. 8) Front brake lever. 9) Gear change pedal. 10) Rear brake pedal. fig.
7) Blue light . Comes on when right high beam is on. 8) Water temperature indicator . Indicates engine coolant temperature. Important Stop riding if the temperature reaches the max. value, otherwise the engine might damage. When parking light is on, the instrument panel is lighted. 1 a 5 3 7 4 2 6 c ATICORS UC D E Instrument panel (fig. 3) 1) Speedometer (km/h or mph). Gives road speed. a) Odometer (km or miles). Gives total distance covered. b) Trip meter (km or miles).
Keys (fig. 4) Your Ducati was delivered with two universal keys for ignition, steering lock and seat catch and a key identification plate (1). Note Separate the two keys and keep the identification plate (1) in a safe place. 1 fig.
Key-operated ignition switch and steering lock (fig. 5) It is located in front of the fuel tank and has four positions: A) ON: lights and engine enabled; B) OFF: lights and engine disabled; C) LOCK: steering locked; D) P: parking light and steering lock. Warning This vehicle is equipped with an energy-saving CPU. If the key stays ON for a long period but the ignition button is not pressed within 15 seconds, the CPU will stop operating to avoid current absorption. Move the key to OFF and then to ON again.
Left switch 1) Switch, light switch, 3 positions: Down = light off; Centre = front and rear parking light, number plate light and panel lights on; Up = headlamp, front and rear parking light, number plate light and panel lights on. 5 2 Note This device is not fitted on the Australia and Japan versions. 2) Dip switch, light dip switch, two positions: position = low beam on; position = high beam on. 3) Switch = 3-position turn indicator: centre position = off; position = left turn; position = right turn.
Clutch lever (fig. 7) Lever (1) disengages the clutch. It features a dial adjuster (2) for lever distance from the twistgrip on handlebar. To set lever distance from twistgrip, push lever (1) fully forward and turn the dial adjuster (2) to one of its four positions. Remember that position no. 1 gives maximum distance between lever and twistgrip, whereas lever and twistgrip are closest when adjuster is set to position no. 4.
Starter lever (fig. 8) The starter lever (1) is used to start the engine from cold and to increase the engine idle rotation speed after starting. Control positions: A - (vertical) Control not activated B - Control fully activated The lever may also be placed on intermediate positions to match the progressive engine warming up (see page 33). A B Important Never use this device when the engine is warm. Do not run with the starter control on. 1 16 fig.
Right switch (fig. 9) G) Switch for ENGINE STOP, two positions: position (RUN) = run. position (OFF) = stop. Warning This switch is mainly intended for use in emergency cases when you need to stop the engine quickly. After stopping the engine, return the switch to the position to enable starting. Front brake lever (fig. 9) Pull in the lever (4) towards the twistgrip to operate the front brake. The system is hydraulically operated and you just need to pull the lever gently.
Rear brake pedal (fig. 10) Push down on the pedal (1) with your foot to operate the rear brake. The system is hydraulically operated. Gear change pedal (fig. 11) The gear change pedal is at rest when in the central position N, is moved up and down to change gears and then returns to the central position. down = push down on the pedal to engage 1st gear and to shift down. The N light will go out. up = lift the pedal to engage the 2nd gear and then the 3rd, 4th, 5th and 6th gear.
Adjustment of gear change and rear brake pedals (fig. 11.2 and 11.3) Gear change and rear brake pedals can be set in a preferred position relative to footpegs to better suit the riding style of every rider. To set the gear change pedal, lock linkage (1) and loosen check nuts (2) and (3). Note Nut (2) has a left-hand thread. Apply an open-end wrench to the hexagon portion of linkage (1) and rotate linkage until the gear change pedal is in the desired position.
To set the rear brake pedal: loosen check nut (4). Turn travel adjuster (5) until pedal is in the desired position. Tighten check nut (4). Work the pedal by hand to make sure it has about 1.5 ÷ 2 mm free play before brake is actuated. If not so, set master cyilinder rod length as follows: loosen the check nut (6) on the rod. Tighten rod into fork (7) to increase free play or loosen it to decrease play. Tighten the check nut (6) and check play again. fig. 11.
MAIN COMPONENTS AND DEVICES Location (fig. 12) 1) Tank filler plug. 2) Seat catch. 3) Side stand. 4) Hook for helmet fastening cable. 5) Steering damper. 6) Rear view mirrors. 7) Front fork adjusters. 8) Rear shock absorber adjusters. 9) Motorcycle track alignment linkage. fig.
Tank filler plug (fig. 13) Opening Lift the protection lid (1) and fit the ignition key into the lock. Turn the key clockwise 1/4 turn to unlock. Lift the plug. Closing Refit the plug with the key in it and push it down into its seat. Turn the key anticlockwise to its initial position and take it out. Close the lock protection lid (1). Note The plug can only be closed with the key in. Warning Always make sure you have properly refitted (see page 37) and closed the plug after each refueling.
Opening (fig. 14.1) Fit the ignition key into the lock (1) and turn the key clockwise. Pull gently the tail guard (2) outwards and lift it until it rests onto the fuel tank. On the rear end of the compartment underneath the seat, there is the helmet fastening cable. Insert the cable (A) into the helmet and insert the ends of the cable into the hook. Leave the helmet hanging outside (fig. 14.2) and refit the seat.
Side stand (fig. 15) Important Before lowering the side stand, make sure that the bearing surface is hard and flat. Warning The motorcycle can be started only if the side stand is up as its safety device prevents engine start when the stand is down. Do not park on soft or pebbled ground or on asphalt melt by the sun heat and similar or the motorcycle may fall over. When parking in downhill road tracts, always park the motorcycle with its rear wheel facing downhill.
Steering damper (fig. 16) The steering damper is before the tank and is secured to the frame and the steering head. It gives improved steering accuracy and stability, thus also improving motorcycle road behavior under any riding conditions. Turn the knob (1) clockwise for a harder setting (2), counter clockwise for a softer setting (3). A click identifies the different settings. 2 Warning Never attempt to set knob (1) while riding, or you may lose control of the motorcycle.
Front fork adjusters The front fork has rebound and compression damping adjusters. 1 This adjustment is done using the outer adjusters: 1) (fig. 17.1) to adjust rebound damping; 2) (fig. 17.1) to adjust inner springs preload; 3) (fig. 17.2) to adjust compression damping. 2 Put and secure the motorcycle in vertical position. Turn the adjuster (1) on fork leg top with a 3-mm Allen wrench to adjust rebound damping. To reach the adjuster (3), insert a 3-mm Allen wrench into the hole as shown in fig. 17.2.
STANDARD factory setting is as follows: compression: 10 clicks; rebound: 12 clicks. Max. setting for softest damping adjustment is 24 clicks for rebound and 28 clicks for compression. To change the preload of the spring inside each fork leg, turn the hex. adjusting nut (2) with a 22-mm hexagon wrench. Factory setting is 10 mm. Important Adjust both fork legs to same settings.
Shock absorber adjusters (fig. 18) The shock absorber has outer adjusters that enable you to adjust your motorcycle to the load. The adjuster (1) located on the left side, on the connection holding the shock absorber to the swingarm, controls rebound damping. The adjuster (2) on the shock absorber expansion reservoir controls compression damping. Turn the adjusters (1 and 2) clockwise to increase damping, anticlockwise to reduce it.
Changing motorcycle track alignment (fig. 19.2) Motorcycle track alignment is the result of tests carried out under different riding conditions by our technical staff. Modifying factory setting is a very delicate operation, which may lead to serious damages if carried out by unskilled people. Before changing standard setting, measure the reference value (H, fig. 19.1).
DIRECTIONS FOR USE For all mechanical moving parts of the motorcycle to adapt to one another and above all not to adversely affect the life of basic engine parts, it is advisable to avoid harsh accelerations and not to run the engine at high rpm for too long, especially uphill. Furthermore, the drive chain should be inspected frequently. Lubricate and tighten it as required.
After 2500 km After running-in, never exceed the following values during the motorcycle standard use: 10000 rpm Strict observance of running-in recommendations will ensure longer engine life and reduce the likelihood of overhauls and tune-ups. MIN-1 x1000 fig.
Pre-ride checks Warning Failure to carry out these checks before riding, may lead to motorcycle damage and injury to rider. Before riding, perform a thorough check-up on your bike as follows: Fuel level in the tank Check fuel level in the tank. Fill tank if needed (page 37). Engine oil level Check oil level in the sump through the sight glass. Top up with recommended oil if needed (page 55). Brake and clutch fluid Check fluid level in the relevant reservoirs.
Starting the engine ON N O K Regular ambient temperature (10 to 35°C): 1) Move the ignition key to ON (fig. 21.1). Make sure both the green light N and the red light on the instrument panel come on. L OC Warning Before starting the engine, become familiar with the controls you will need to use when riding. N F O OF PUSH Note Follow the “High ambient temperature” procedure to start the engine when it is warm. P IG N IT I fig. 21.
2) Move the starter lever (1) to (B) (fig. 21.2). 3) Check that the stop switch (3, fig. 21.3) is positioned to (RUN), then press the ignition button (4). Let the engine start without using the throttle control. A B Important Never operate the electric start button more than 5 seconds at a time. If needed, allow 10 seconds before attempting to restart the engine. 4) Move the starter lever (1) to its vertical position (A) (fig. 21.2). Important Do not rev up the engine when it is cold.
Moving off 1) Disengage the clutch squeezing the control lever. 2) Push down on gear change lever sharply with the tip of your foot to engage the first gear. Once released, the lever will spring back to its original position. 3) Speed up engine, by turning the throttle twistgrip and slightly releasing the clutch lever at the same time. The motorcycle will start moving off. 4) Let go of clutch lever and speed up.
Stopping the motorcycle If you let go of the throttle twistgrip, the motorcycle will slow down gradually and smoothly. Then, shift down releasing the clutch, and finally change from first to neutral. Apply brakes and you will bring the motorcycle to a complete stop. To switch the engine off, simply turn the key to OFF (page 13). Important Never leave the key in the ON position when engine is stopped, or this will damage the electric components.
Refueling (fig. 22.1) Never overfill the tank when refueling. Fuel should never be touching the rim of filler recess. Max level ;;;; Warning Be sure there is no fuel trapped in the filler recess. fig.
Tool kit and accessories (fig. 23) Located in the compartment (1) under the tail: an Owner’s manual; a helmet fastening cable; a tool bag for usual maintenance and checks. 1 To reach this compartment, the tail guard must be lifted by opening the catch (page 23). The tool bag (fig.
MAIN MAINTENANCE OPERATIONS Side body panels (fig. 25) To remove the body panels proceed as follows: unscrew the three fasteners (1) placed under the fairing RH and LH side; unscrew the four headlamp fairing fasteners (2); unscrew the four frame fasteners (3). Removing the fairing Some servicing operations need the motorcycle fairing to be removed.
Headlamp fairing (fig. 26.1) Undo the middle fastening screw (1) of the wing mirrors and remove them from the headlamp fairing supports. Undo the two fastening screws (2, fig. 26.2) of the headlight support and disconnect the four connectors (3) joining the two body panels together. Important At reassembly, apply “medium-strength threadlocker” onto the screw threading (1). 1 fig. 26.1 2 3 fig. 26.
Cleaning and changing air filters (fig. 27.2) The air box is accessible after removing the body panels and the headlamp fairing (see page 39). Undo the eight fastening screws of the outer cover (1, fig. 27.1). Remove the cover but leave it hanging from the turn indicator cable. Do not remove the reduction element (4, 998 only) from its seat. Remove the filter (2, fig. 27.2) from its seat on the inner cover (3). Clean the filter cartridge with compressed air or fit a new one, if needed.
Checking the coolant level (fig. 28.1) Check the coolant level in the expansion reservoir, on the LH side of the motorcycle. The coolant level must be between the MAX and MIN marks. Top up if the level is too low. Remove the l.h. body panel and the fuel tank. Lift the tail guard and undo the rear screw (2, fig. 28.2). Remove the tank from its front clamping by pulling the tank backwards. Move it to the right leaving fuel tubing connected. Unscrew the filler (1, fig. 28.
Checking brake and clutch fluid level Fluid level should never fall below the MIN mark on each reservoir (fig. 29). If level drops below the limit, air might get into the circuit and affect the operation of the system involved. Brake and clutch fluid must be topped up and changed at the intervals specified in the routine maintenance chart (see the Warranty Booklet) by a Ducati Dealer or Authorized Workshop. Important It is recommended all brake and clutch tubes be changed every four years.
Checking brake pads for wear (fig. 30) To facilitate inspection without removing the pads from the calipers, brake pads have a wear mark. If the grooves in the friction material are still visible, the pad is still in good condition. Important Have the brake pads replaced at a Ducati Dealer or Authorized Workshop. Lubricating cables and joints The condition of the outer sheath of the throttle/starter cable should be checked at regular intervals. The sheath should show no signs of squeezing or cracking.
Throttle cable adjustment The throttle twistgrip must have a free play of 1.5 - 2 mm measured at the edge of the twistgrip, at all positions of the handlebars. If it needs adjusting, use the suitable adjuster (2, fig. 31) provided on the throttle control. Charging the battery (fig. 32) Before charging the battery, it is best to remove it from the motorcycle. Remove the r.h. body panel (page 39), undo the screw (1) and remove the upper bracket.
Charge the battery in a ventilated room. Connect the battery charger leads to the battery terminals - red to positive terminal (+), black to negative terminal (-). Important Make sure the charger is off when you connect the battery to it, or you might get sparks at the battery terminals that could ignite the gases inside the cells. Always connect the positive terminal (red) first (+). Refit the battery on its mount and secure the top bracket with screw (1). Connect the terminals.
Adjusting headstock angle (fig. 33.1) Loosen the two screws (1) on the frame r.h. side to adjust the headstock angle. Fully unscrew the screw (2) and turn the headstock end (3) by 180° with a pin wrench. Check that the hole on the eccentric is in line with the passing hole of the steering head. To this purpose an arrow indicating the phase is punched onto the eccentric (upper side). Fully screw the screw (2). Grease the screw threadings (1) with SHELL Retinax HDX2 and tighten to 22 Nm.
Chain tension inspection (fig. 34) With the motorcycle on the side stand, the chain must have a min. distance of 25 mm from the swingarm. If this is not the case, contact a Ducati Dealer or Authorized Workshop for proper chain tensioning. Warning Correct tightening of the eccentric hub clamping screws is essential to rider’s safety. Chain lubrication The chain fitted on your motorcycle has OR seals that keep dirt out of and lubricant inside the sliding parts.
Replacing bulbs Before replacing a burnt-out bulb, make sure that the new one complies with voltage and wattage as specified on page 66, “Electric System”, for that lighting device. Always check for new bulb proper operation before refitting removed parts. 4 Headlamp To gain access to headlamp bulbs proceed as follows: Disassembly: low beam bulb (fig. 35.1): remove the rubber cover (1). Press the lower quick-release button to disconnect the connector (2). 1 2 fig. 35.1 L.h. high beam bulb (fig. 35.
Reassembly: insert the locating pegs of the bulb base into their seats to obtain correct alignment. Hook the clip (4, fig. 35.2) to the headlamp holders; reconnect the cables and refit the rubber cover (1, fig. 35.2). Instrument panel (fig. 36) Remove the headlamp fairing (see page 39) to reach the instrument panel bulbs. One or two lamps are fitted under each instrument. Pull out the bulb holder (1) under the instrument involved, remove the bulb and fit a new one.
Turn indicators (fig. 37) Remove the screw (1) and detach the glass (2) from the body. The bulb is of the bayonet-type: press and rotate anticlockwise to remove; fit the spare bulb by pressing and turning clockwise until it clicks. Refit the glass sliding the small tab (A) into the suitable slot in the indicator body and tighten the screw (1). 2 A Stop light (fig. 38.1) To expose the number plate bulb, withdraw the lamp holder from the number plate holder, then extract the bulb and replace it.
Number plate light (fig. 38.2) To expose the number plate bulb, take the lamp holder out of the number plate mount, extract the bulb and replace it. Beam setting (fig. 39.1) When checking the beam setting, put the motorcycle upright. Tyres should be inflated at the correct pressure and one person should be sitting astride the motorcycle, keeping it at right angles to its longitudinal axis.
Rear view mirror adjustment Slacken the screw in the hole (2, fig. 39.2) with a crosspoint screwdriver. Set the rear view mirror by hand and tighten the screws. fig. 39.1 2 Tubeless tyres Tyre pressure Front: 2.1 bar - 2.3 Kg/sq cm Rear: 2.2 bar - 2.4 Kg/sq cm As tyre pressure is affected by temperature and altitude variations, you are advised to check and adjust it whenever you are riding in areas where ample variations in temperature or altitude occur.
Tyre repair or replacement (tubeless tyres) In the event of a tiny puncture, tubeless tyres will take a long time to deflate, as they tend to keep air inside. If you find low pressure on one tyre, check the tyre for punctures. Warning A tyre must be replaced when punctured. Replace tyres with recommended standard tyres only. Be sure to tighten the valve caps securely to avoid leaks when riding. Never use tube type tyres.
Checking engine oil level (fig. 41) Engine oil level can be checked through the sight glass (1) provided on the clutch cover. When checking oil level, the motorcycle should be upright and the engine cold. Oil level should be between the marks near the sight glass Top up oil level with SHELL Advance Ultra 4, if low. Undo the filler plug (2) and top up to correct level. Refit the plug.
Important If the gap needs adjusting, be very careful when bending the side electrode. If gap is too wide or too close, engine performance will be affected. This could also cause difficult starting or irregular idling. Clean the electrode and the insulating material accurately using a small metal brush and check seal condition. Clean the seat in the cylinder head. Be careful not to let any foreign matters fall into the combustion chamber. Refit spark plug into cylinder head.
Cleaning the motorcycle To preserve the finish of metal parts and paintwork, wash and clean your motorcycle at regular intervals, anyway according to the road conditions you ride in. Use specific products only. Prefer biodegradable products. Avoid aggressive detergents or solvents. Never grease or lubricate the brake discs. Loss of braking and further accidents may occur. Clean the discs with an oil-free solvent. Important Do not wash your motorcycle right after use.
Storing the bike away If the motorcycle is to be left unridden over long periods, it is advisable to carry out the following operations before storing it away: clean the motorcycle; remove tank drain plug and seal and drain all fuel from tank; pour a few drops of engine oil into the cylinders through the spark plug seats, then crank the engine by hand a few times so a protective film of oil will spread on cylinder inner walls; place the motorcycle on the paddock stand; disconnect and remove the battery.
TECHNICAL DATA Overall dimensions (mm) (fig. 43) Weights Dry weight: 190 kg. Carrying full load: 310 kg. Warning Failure to observe weight limits could result in poor handling and impair the performance of your motorcycle, and you may lose control of the motorcycle. fig.
Top-ups Type of fluid cu dm (liters) Fuel tank, including a reserve of 4 cu dm (liters). Gasoline 95-98 RON 17 Oil sump and oil filter SHELL - Advance Ultra 4 3.7 Front/Rear brake and clutch circuits Special fluid for hydraulic systems SHELL - Advance Brake DOT 4 — Protectant for electric contacts Spray for electric systems SHELL - Advance Contact Cleaner — Front fork SHELL - Advance Fork 7.5 or Donax TA 0.
Engine Twin cylinder, four-stroke, 90° “L” type, longitudinal. Bore mm: 100 Stroke mm: 63,5 Total displacement c.c.: 998 Compression ratio: 1:11.4±0.5 Max. power at crankshaft (95/1/CE) kW/HP: 100/136 at 10,200 rpm Max torque at crankshaft (95/1/CE): 10.3 Kgm at 8,000 rpm Max. rotation speed 11,500 rpm. Desmodromic timing system (fig. 45) 1) Opening (or upper) rocker. 2) Opening rocker shim. 3) Closing (or lower) rocker shim. 4) Return spring for lower rocker. 5) Closing (or lower) rocker. 6) Camshaft.
Performance data Maximum speed in any gear should be reached only after a correct running-in period with the motorcycle properly serviced at the recommended intervals. Max. speed (rider alone): 260 Km/h Spark plugs Make: CHAMPION Type: RG 4 HC Brakes Front brake With double semifloating drilled disc. Material: steel Disc diameter: 320 mm Hydraulically operated by a control lever on right handlebar. Braking surface: 79 sq cm Brake calipers with separate pistons. Make: BREMBO Type: 34-4 pistons.
Transmission Dry clutch operated by a control lever on left handlebar. Drive is transmitted from engine to gearbox main shaft via spur gears. Gear ratio: 32/59. 6-speed gearbox with constant mesh gears, gear change pedal on left side of motorcycle. Front/rear sprocket ratio: 15/36 Total gear ratios: 1st gear 15/37. 2nd gear 17/30. 3rd gear 20/28. 4th gear 22/26. 5th gear 23/24. 6th gear 24/23. Important The above gear ratios are the homologated ones and under no circumstances must they be modified.
Frame Tubular trellis frame with upper section made of highstrength steel. Steering angle (on each side): 27° For improved performance on track the headstock angle can be changed (see page 47). STANDARD steering setting for road riding is as follows: Steering head angle: 24°30’ Trail: 97 mm. For track riding, setting can be modified to the following values: Steering head angle: 23°30’ Trail: 91 mm. Wheels Five-spoke light-alloy rims. Front wheel Dimensions: 3.50x17" Rear wheel Dimensions: 5.
Suspensions Front Hydraulic upside-down fork provided with outer adjusters for rebound, compression, and preload (for inner springs of fork legs). Stanchion diameter: 43 mm. Travel along leg axis: 127 mm. Rear Of the progressive type, thanks to a rocker arm connecting frame and upper pivot point of the shock absorber and an arch connected at the bottom to swingarm. The shock absorber enables the adjustment of rebound and compression damping and spring preload.
Electric system Basic electric items are: front headlamp consisting of the following: 12V-55W low beam unit, poly-ellipsoidal with capacitor; 12V-55W high beam unit; parking light with no. 2 12V-5W bulbs. Instrument panel, 12V-1.2W warning lights; 12V-2W instrument lights. Electrical controls on handlebars. Turn indicators, 12V-10W bulbs. Horn. Stop light switches. Battery 12V-10 Ah. Generator 12V-520W. Electronic voltage regulator (rectifier), protected by a 40A fuse near the battery. Starter motor, 12V-0.
2 fig. 45.1 2 INTEGRO BRUCIATO INTEGRO QUEMADO fig. 45.3 1 fig. 45.
Legend of the wiring diagram of electric system/ignition 1) Right switch 2) Key-operated switch 3) Ignition relay 4) Fuse box 5) Flasher 6) Water temperature sensor 7) RH electric fan 8) Starter motor 9) Solenoid starter 10) Battery 11) Regulator fuse 12) Regulator 13) Generator 14) Rear right-turn indicator 15) Tail light 16) Number plate lighting bulb 17) Rear left-turn indicator 18) Fuel tank 19) Diagnosis connector 20) Injection relay 21) Horizontal cylinder coil 22) Vertical cylinder coil 23) Horizonta
Wire color coding W-Y White-Yellow P Pink Y-G Yellow-Green G Green R-G Red-Green W-R White-Red W White V-Bk Violet-Black Y Yellow W-G White-Green Bn Brown G-W Green-White W-Bk White-Black R-Bk Red-Black R-B Red-Blue Gr-R Grey-Red R Red W-Bn White-Brown O Orange Bn-W Brown-White Y-Bk Yellow-Black Gr Grey B-Bk Blue-Black Lb Light blue Bk Black V-W Violet-White Y-B Yellow-Blue Bn-G Brown-Green G-Gr Green-Grey O-G Orange-Green Gr-Y Grey-Yellow Gr-B Grey-Blue O-B Orange-Blue 69
Legend of fuse box (4) Pos. Description Rat. 1-9 Main switch 30 A 2-10 Fuel pump, injectors, coils 20 A 3-11 Key sense 7.5 A 4-12 CPU power supply 3A 5-13 High beam and low beam 15 A 6-14 Turn indicators, warning lights, tail lights and instrument panel lights 10 A 7-15 Stop, warning horn 7.5 A 8-16 Cooling electric fan 7.5 A Note The electric system wiring diagram is at the end of this manual.
ROUTINE MAINTENANCE RECORD km Ducati Service Name Mileage Date 1,000 10,000 20,000 30,000 40,000 50,000 71
DUCATIMOTOR HOLDING S.p.A. Via Cavalieri Ducati, 3 40132 Bologna, Italy Tel 39.051.6413111 Fax 39.051.406580 www.ducati.com 72 913.7.073.
