Portable LCD Projector Model 8943 8918 USER’S MANUAL #070030
Projector 8918/8943 User's Manual – Operating Guide Thank you for purchasing this projector. WARNING Before using this product, please read the “Safety Guide” section and related sections to ensure the proper use of this product. After reading section, store this in a safe place for future reference. About this manual Various symbols are used in this manual. The meanings of these symbols are described below.
Content Content About this manual. . . . . . . . . . 1 Content . . . . . . . . . . . . . . . . . . 2 Projector features. . . . . . . . . . 3 Preparations . . . . . . . . . . . . . . 3 Contents of package . . . . . . . . . . . . .3 Fastening the lens cover . . . . . . . . . .3 Part names . . . . . . . . . . . . . . . 4 Projector . . . . . . . . . . . . . . . . . . . . . .4 Control panel . . . . . . . . . . . . . . . . . . .5 Rear panel . . . . . . . . . . . . . . . . . . . . .5 Remote control . . . . . . .
Projector features / Preparations Projector features This projector is used to project various picture signals onto a screen. This projector requires only a minimal amount of space for installation and can produce a large projected image from even a short distance. Preparations Contents of package Please see the “Contents of package” in the “User’s Manual (concise)” which is a book. Your projector should come with the items shown there. Contact immediately your dealer if anything is missing.
Part names Part names Projector (1) Speakers (x 4) (37). (2) Focus ring (19) (3) Zoom ring (19) (4) Lamp cover (56) The lamp unit is inside. (5) Lens shift cover (19) (6) Horizontal lens shift dial (19) (7) Vertical lens shift dial (19) (8) Front cover (9) Lens (61) (10) Lens cover (3) (11) Remote sensors (x 3) (14) (12) Elevator feet (x 2) (9) (13) Elevator knobs (x 2) (9) (14) Filter cover (58) The air filter and intake vent are inside.
Part names Control panel (1) STANDBY/ON button (16) (2) MENU button (23) It consists of four cursor buttons. (3) INPUT button (17) (4) POWER indicator (16) (5) TEMP indicator (63) (6) LAMP indicator (63) (6) (5) (4) SD CARD RGB OUT AUDIO IN 1 AUDIO IN 2 S-VIDEO RGB1 Y VIDEO RGB2 M1-D CB/PB (1) R LAN AUX I/O DC 5V 0.
Part names Remote control (1) Laser pointer (13) It is a beam outlet.
Setting up Setting up Install the projector according to the environment and manner the projector will be used in. WARNING ►Place the projector in a stable horizontal position. If the projector falls or is knocked over it could cause injury and/or damage to the projector. Using a damaged projector could then result in fire and/or electric shock. • Do not place the projector on an unstable, slanted or vibrational surface such as a wobbly or inclined stand.
Setting up Arrangement Refer to the illustrations and tables below to determine screen size and projection distance.
RGB OUT VIDEO RGB1 Y RGB2 M1-D CB/PB Setting up CR/PR Adjusting the projector's elevator When the place to put the projector is slightly uneven to the left or right, use the REMOTE CONTROL AUDIO elevator feet to place the projector horizontally. S-VIDEO (3.5Φ) R L R L OUT CONTROL 3 AUDIO IN 4the projector in order to project at Using theAUDIO feetINcan also tilt q a suitable angle to the screen, elevating the front side ofACthe IN projector within 8 degrees.
Setting up Connecting your devices Be sure to read the manuals for devices before connecting them to the projector. Make sure that all the devices are suitable to be connected with this product, and prepare the cables required to connect. Please refer to the following illustrations to connect them.
Setting up Connecting your devices (continued) NOTE • Be sure to read the manuals for devices before connecting them to the projector, and make sure that all the devices are suitable to be connected with this product. Before connecting to a PC, check the signal level, the signal timing, and the resolution. - Do not connect LAN port to any network that might have the excessive voltage. - Some signal may need an adapter to input this projector.
Setting up Connecting power supply 1. Connect the connector of the power cord to the AC inlet of the projector. 2. Firmly plug the power cord's plug into the outlet. AC inlet Connector of the power cord to the outlet WARNING ►Please use extra caution when connecting the power cord, as incorrect or faulty connections may result in fire and/or electrical shock. • Only use the power cord that came with the projector. If it is damaged, contact your dealer to newly get correct one.
Remote control Remote control Laser pointer This remote control has a laser pointer in place of a finger or rod. The laser beam works and the LASER INDICATOR lights while the LASER button is pressed. LASER INDICATOR LASER button WARNING ►The laser pointer of the remote control is used in place of a finger or rod. Never look directly into the laser beam outlet or point the laser beam at other people. The laser beam can cause vision problems.
Remote control About the remote control signal The remote control works with the projector’s remote sensors. This projector has three remote sensors on the front, on the top, and on the back. The sensors can be respectively turned active or inactive using the “REMOTE RECEIV” in the SERVICE item of OPTION menu (46). Each sensor senses the signal within the following range when the sensor is active. The front and top sensors: 60 degrees (30 degrees to the left and right of the sensor) within 3 meters about.
RGB OUT AUDIO IN 1 AUDIO IN 2 RGB1 Y VIDEO RGB2 M1-D CB/PB CR/PR S-VIDEO R AUDIO IN 3 L Remote control REMOTE CONTROL (3.5Φ) AUDIO OUT R L AUDIO IN 4 CONTROL Using as a wired remote control LAN AC IN LASE INDIC R ATOR The accessory remote control works as a wired remote control, when the wired control port at the bottom of the remote control connects with the REMOTE CONTROL port on the back of the projector via an audio cable with 3.5 diameter stereo mini plugs.
Power on/off Power on/off Turning on the power sure that the power cord is firmly and 1. Make correctly connected to the projector and the outlet. the lens cover, and set the power switch to 2. Remove the ON position. STANDBY/ON button POWER indicator LASER INDICATOR STANDBY/ON VIDEO BLANK RGB The power indicator will light up in steady orange (63). Then wait several seconds because the buttons may not function for these several seconds.
BLANK LASER Operating LASER INDICATOR Operating STANDBY/ON VIDEO RGB ASPECT Adjusting the volume the VOLUME button on the remote control. 1. Press A dialog will appear on the screen to aid you in adjusting the volume. the cursor buttons ▲/▼ to adjust the volume. 2. Use To close the dialog and complete the operation, press the PUSH ENTER PAGE UP BLANK ESC PAGE DOWN LASER RESET MENU POSITION AUTO MAGNIFY MY BUTTON ON 1 VOLUME button again.
LASER INDICATOR Operating STANDBY/ON VIDEO STANDBY/ON VIDEO Selecting an input signal (continued) 1. Press the VIDEO button on the remote control to select an input for video signal. Each time you press the button, the projector switches its video input port as below.
Operating Adjusting the zoom and focus 1. Use the zoom ring to adjust the screen size. 2. Use the focus ring to focus the picture. Adjusting the lens shift 1. Use the vertical lens shift dial to shift the picture upward or downward. the horizontal lens shift dial to 2. Use shift the picture left or right. NOTE • When the vertical lens shift is adjusted, it is recommended to shift the picture upward.
Operating Adjusting the position the POSITION button on the remote control. 1. Press The “POSITION” indication will appear on the screen. the cursor buttons ▲/▼/◄/► to adjust the picture 2. Use position. ASPECT PUSH ENTER PAGE UP ESC PAGE DOWN LASER MENU INDICATOR RESET STANDBY/ON POSITION VIDEO AUTO RGB MAGNIFY MY BUTTON VOLUME ON 1 When you want to reset the operation, press the RESET button on the remote control during the operation.
Operating ASPECT PUSH Using the magnify feature ENTER PAGE UP the ON button of MAGNIFY on the remote control. 1. Press The “MAGNIFY” indication will appear on the screen (although the indication will disappear in several seconds with no operation), and the projector will go into the MAGNIFY mode. PAGE DOWN ESC MENU POSITION AUTO RESET MAGNIFY MY BUTTON ON 1 VOLUME MUTE OFF 2 FREEZE KEYSTONE SEARCH the cursor buttons ▲/▼ to adjust the zoom level. 2.
Operating LASER INDICATOR STANDBY/ON VIDEO RGB Temporarily blanking the screen the BLANK button on the remote control. 1. Press The blank screen will be displayed instead of the screen of input signal. Please refer to the BLANK item in SCREEN menu (38). To exit from the blank screen and return to the input signal screen, press the BLANK button again.
Operating LASER INDICATOR STANDBY/ON Using the menu function VIDEO RGB This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK, and EASY MENU. EASY MENU consists of functions often used, and the other menus are classified into each purpose. Each of these menus is operated using the same methods. The basic operations of these menus are as follows. BLANK LASER ENTER button ASPECT PUSH Cursor buttons MENU button RESET button 1.
EASY Menu '#5; /'07 =4)$ ? EASY Menu From the EASY MENU, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons on the projector or remote control. Then perform it according to the following table. Item ASPECT #52'%6 #761 -';5610' ':'%76' -';5610' -';5610' 2+%674' /1&' 014/#. $4+)*60'55 %1064#56 %1.14 6+06 5*#420'55 9*+52'4 014/#. /+4414 014/#. 4'5'6 (+.6'4 6+/' J .#0)7#)' '0).
EASY Menu EASY Menu (continued) Item BRIGHTNESS CONTRAST COLOR TINT SHARPNESS WHISPER MIRROR Description Using the ◄/► buttons adjusts the brightness. See the BRIGHTNESS item in PICTURE menu (26). Using the ◄/► buttons adjusts the contrast. See the CONTRAST item in PICTURE menu (26). Using the ◄/► buttons adjusts the strength of whole color. See the COLOR item in PICTURE menu (27). Using the ◄/► buttons adjusts the tint. See the TINT item in PICTURE menu (27).
PICTURE Menu PICTURE Menu From the PICTURE menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons on the projector or remote control, and press the ► cursor button on the projector or remote control, or the ENTER button on the remote control to execute the item. Then perform it according to the following table. Item BRIGHTNESS CONTRAST /'07 =4)$ ? 2+%674' +/#)' +0276 5'672 #7&+1 5%4''0 126+10 0'6914 '#5; /'07 5'.
PICTURE Menu PICTURE Menu (continued) Item Description Using the ▲/▼ buttons switches the color temperature mode.
PICTURE Menu PICTURE Menu (continued) Item Description Using the ▲/▼ cursor buttons changes the active iris control mode. PRESENTATION ó THEATER ó TURN OFF ACTIVE IRIS PRESENTATION THEATER TURN OFF Feature The active iris displays the best presentation image for both bright and dark scenes. The active iris displays the best theater image for both bright and dark scenes. The active iris is always open. • The screen may flicker when the PRESENTATION or THEATER modes are selected.
IMAGE Menu IMAGE Menu From the IMAGE menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons on the projector or remote control, and press the ► cursor button on the projector or remote control, or ENTER button on the remote control to execute the item. Then perform it according to the following table. Item /'07 =4)$ ? 2+%674' +/#)' +0276 5'672 #7&+1 5%4''0 126+10 0'6914 '#5; /'07 5'.
IMAGE Menu IMAGE Menu (continued) Item Description H PHASE Using the ▲/▼ buttons adjusts the horizontal phase to eliminate flicker. Right ó Left • This item can be selected only for an RGB signal or a component video signal. (except 525i (480i), 625i (576i), SCART RGB) H SIZE AUTO ADJUST EXECUTE 30 Using the ▲/▼ buttons adjusts the horizontal size. Large ó Small • This item can be selected only for an RGB signal. • When this adjustment is excessive, the picture may not be displayed correctly.
INPUT Menu INPUT Menu From the INPUT menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons on the projector or remote control, and press the ► cursor button on the projector or remote control, or ENTER button on the remote control to execute the item. Then perform it according to the following table. /'07 =4)$ ? 2+%674' +/#)' +0276 5'672 #7&+1 5%4''0 126+10 0'6914 '#5; /'07 5'.'%6 241)4'55+8' 68 8+&'1 04 /+& & ;%5 56+.. %1.
INPUT Menu INPUT Menu (continued) Item Description Using the ▲/▼ buttons switches the function of the COMPONENT (Y, Cb/Pb, Cr/Pr) port. COMPONENT ó SCART RGB When the SCART RGB is selected, the COMPONENT (Y, Cb/Pb, Cr/Pr) and VIDEO ports will function as a SCART RGB port. A SCART adapter or SCART cable is required for a SCART RGB input to the projector. For details, contact your dealer.
INPUT Menu INPUT Menu (continued) Item FRAME LOCK RGB IN Description Using the ▲/▼ buttons turns the frame lock function on/off. TURN ON ó TURN OFF • This item can be performed only on an RGB signal with a vertical frequency of 50 to 60 Hz. • When the TURN ON is selected, a moving pictures are displayed more smoothly. • This function may cause a certain degradation of the picture. In such a case, please select the TURN OFF. Set the RGB input signal type for the RGB port.
INPUT Menu INPUT Menu (continued) Item Description The resolution for the RGB1 and RGB2 input signals can be set on this projector. (1) In the INPUT menu select the RESOLUTION using the ▲/▼ buttons and press the ► button. 4'51.76+10 The RESOLUTION menu will be displayed. (2) In the RESOLUTION menu select the resolution you wish to display using the ▲/▼ buttons. Selecting AUTO will set a resolution appropriate to the input signal.
SETUP Menu SETUP Menu From the SETUP menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons on the projector or remote control, and press the ► cursor button on the projector or remote control, or the ENTER button on the remote control to execute the item. Then perform it according to the following table. Item /'07 =4)$ ? 2+%674' +/#)' +0276 5'672 #7&+1 5%4''0 126+10 0'6914 '#5; /'07 5'.
SETUP Menu SETUP Menu (continued) Item WHISPER Description Using the ▲/▼ buttons turns off/on the whisper mode. NORMAL ó WHISPER • When the WHISPER is selected, acoustic noise and screen brightness are reduced. Using the ▲/▼ buttons switches the mode for mirror status. MIRROR NORMAL ó H:INVERT ó V:INVERT ó H&V:INVERT If the Transition Detector is TURN ON and MIRROR status is changed, Transition Detector Alarm (51) will be displayed when projector is restarted after the power switch is turned off.
AUDIO Menu AUDIO Menu From the AUDIO menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons on the projector or remote control, and press the ► cursor button on the projector or remote control, or ENTER button on the remote control to execute the item. Then perform it according to the following table. /'07 =4)$ ? 2+%674' +/#)' +0276 5'672 #7&+1 5%4''0 126+10 0'6914 '#5; /'07 81.7/' 64'$.' $#55 545 919 52'#-'4 #7&+1 5'.
SCREEN Menu SCREEN Menu From the SCREEN menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons on the projector or remote control, and press the ► cursor button on the projector or remote control, or ENTER button on the remote control to execute the item. Then perform it according to the following table. Item /'07 =4)$ ? 2+%674' +/#)' +0276 5'672 #7&+1 5%4''0 126+10 0'6914 '#5; /'07 5'.'%6 .#0)7#)' '0).+5* /'07 215+6+10 $.
SCREEN Menu SCREEN Menu (continued) Item Description Using the ▲/▼ buttons switches the mode for the start-up screen. The start-up screen is a screen displayed when no signal or an unsuitable signal is detected. MyScreen ó ORIGINAL ó TURN OFF MyScreen START UP ORIGINAL TURN OFF Feature Screen can be registered by the MyScreen item (40). Screen preset as the standard screen. Plain black screen.
SCREEN Menu SCREEN Menu (continued) Item Description MyScreen This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and START UP screen. Display the image you want to capture before executing the following procedure. 1. Selecting this item displays a dialog titled “MyScreen”. It will ask you if you start capturing an image from the current screen.
SCREEN Menu SCREEN Menu (continued) Item Description MESSAGE Using the ▲/▼ buttons turns on/off the message function. TURN ON ó TURN OFF When the TURN ON is selected, the following message function works. “AUTO IN PROGRESS” while automatically adjusting “NO INPUT IS DETECTED” “SYNC IS OUT OF RANGE” “Searching….” while searching for the input “Detecting….
OPTION Menu OPTION Menu From the OPTION menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons on the projector or remote control, and press the ► cursor button on the projector or remote control, or ENTER button on the remote control to execute the item, except for the items LAMP TIME and FILTER TIME. Then perform it according to the following table.
OPTION Menu OPTION Menu (continued) Item Description Using the ▲/▼ buttons adjusts the time to count down to automatically turn the projector off. Long (max. 99 minutes) ó Short (min. 0 minute = DISABLE) AUTO OFF AUTO OFF ENABLE AUTO OFF DISABLE 0 When the time is set to 0, the projector is not turned off automatically. When the time is set to 1 to 99, and when the passed time with nosignal or an unsuitable signal reaches at the set time, the projector lamp will be turned off.
OPTION Menu OPTION Menu (continued) Item MY BUTTON Description This item is to assign one of the following function to MY BUTTON 1 and 2 on the remote control (6). Choose 1 or 2 on the MY BUTTON menu using the ◄/► button first. Then using the ▲/▼ buttons sets one of the following functions to the chosen button. • RGB1: Sets port to RGB1. • RGB2: Sets port to RGB2. • M1-D: Sets port to M1-D. • COMPONENT: Sets port to COMPONENT (Y, Cb/Pb, Cr/Pr). • S-VIDEO: Sets port to S-VIDEO.
OPTION Menu OPTION Menu (continued) Item Description AUTO ADJUST Using the ▲/▼ buttons enables/disables the #761 #&,756 automatic adjustment.When DISABLE is selected, '0#$.' &+5#$.' the automatic adjustment feature is disabled, although rough adjustment is automatically performed depending on the basic setting. ENABLE ó DISABLE • Depending on conditions, such as input image, signal cable to the projector, environment around the projector, etc., the automatic adjustment may not work correctly.
OPTION Menu OPTION Menu (continued) Item Description KEY LOCK Using the ▲/▼ buttons turns on/off the key lock feature. When TURN ON is selected, the buttons on the projector except the STANDBY/ON button are locked. TURN ON ó TURN OFF • Please use to avoid a mischief and touching accidentally. This function does not have any effect on the remote control. SERVICE REMOTE RECEIV. (1) Select a remote sensor using the ▲/▼ button.
OPTION Menu OPTION Menu (continued) Item Description This projector is equipped with security functions. User registration is required before using the security functions. Please contact your local dealer. 1. Using Security Features 1.1 Inputting the PASSWORD SECURITY 1.1-1 Use the ▲/▼ buttons on the OPTION menu to select SECURITY and press the ► button. The ENTER PASSWORD box will be displayed. The factory default PASSWORD is 2400. This PASSWORD can be changed (1.2 Changing the PASSWORD).
OPTION Menu OPTION Menu (continued) Item Description 1.3 If you have forgotten your PASSWORD 1.3-1 Follow the procedure in 1.1-1 to display the ENTER PASSWORD BOX. 1.3-2 While the ENTER PASSWORD BOX is displayed, press and hold the RESET button on the remote control for about 3 seconds or press and hold the INPUT and ► buttons on the projector for about 3 seconds. The 10 digit Inquiring Code will be displayed.
OPTION Menu OPTION Menu (continued) Item Description 2.2-4 Move the cursor to the right side of the CHECK PASSWORD BOX and press the /[5ETGGP ► button to display the PASSWORD for %1/2.'6' about 20 seconds, please make note of the PASSWORD during this time. '06'4 ':+6 Pressing the ENTER button on the remote control PASSWORD BOX or INPUT button on the projector will return to MyScreen PASS WORD on/off menu.
OPTION Menu OPTION Menu (continued) Item SECURITY Description 3.1-3 Input a 4 part PIN Code using the ▲/▼/◄/► /RGB and INPUT buttons. 2+0 $1: +PRWV 2+0 %QFG A CONFIRMATION BOX will appear. Reenter the same PIN Code. This will complete the PIN Code 4)$ registration. PIN BOX NOTE: If there is no key input for about 55 seconds while the PIN BOX or the CONFIRMATION BOX are displayed the menu will close.
OPTION Menu OPTION Menu (continued) Item Description 4. Using the Transition Detector Function While the Transition Detector function is ON, when power switch is started to supply to the projector, it might react as below. • Transition Detector alarm shown below might appear on screen, if the projector has been moved or re-installed. • Transition Detector alarm might appear on screen, if the MIRROR setting has been changed.
OPTION Menu OPTION Menu (continued) Item Description 4.3 Setting the Transition Detector off 4.3-1 Follow the procedure in 4.1-1 to display the Transition Detector on/off menu. 4.3-2 Select TURN OFF to display the ENTER PASSWORD BOX (large). Enter the registered PASSWORD and the screen will return to the Transition Detector on/off menu. If an incorrect PASSWORD is input the menu will close. If necessary repeat the process from 4.3-1. SECURITY 4.4 If you have forgotten your PASSWORD 4.
NETWORK Menu NETWORK Menu Consult with your network administrator before connecting to an existing access point on your network. Incorrect network settings on this projector may cause trouble on the network. Select “NETWORK” from the main menu to access the following functions. Select an item using the ▲/▼ cursor buttons on the projector or remote control, and press the ► cursor button on the projector or remote control, or ENTER button on the remote control to execute the item.
NETWORK Menu NETWORK Menu (continued) Item TIME DIFFERENCE Description Entering the TIME DIFFERENCE : Use the ▲/▼ buttons to enter the TIME DIFFERENCE. Set the same TIME DIFFERENCE as the one set on your PC. If unsure, consult your network administrator. Use the ◄ button to return to the menu after setting the TIME DIFFERENCE. 6+/' &+(('4'0%' 㪞㪤㪫㩷㩷㪇㪇㩷㪑㪇㩷 㪇㩷 DATE AND TIME Entering DATE AND TIME : Use the ▲/▼/◄/► buttons to enter the Year (last two digits), Month, Date, Hour and Minute.
NETWORK Menu / Network functions NETWORK Menu (continued) Item Description INFORMATION display : Use the ► or ENTER buttons to view network information and confirm settings. INFORMATION 0'6914- + 0(14/#6+10 0#/' +2 #&&4'55 57$0'6/#5- &'(#7.6 )#6'9#; /#% #&&4'55 #% % 6+/' &+(('4'0%' )/6 ' #0& 6+/' • Only the first 16 characters of the projector name are displayed.
Maintenance Maintenance Lamp A lamp has finite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early replacement are recommended. To prepare a new lamp, contact your dealer and tell the lamp type number. Type number = 456-8943 Replacing the lamp The lamp cover the projector off, and unplug the power cord.
Maintenance Lamp (continued) WARNING HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE ►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
Maintenance Air filter Please check and clean the air filter periodically. If the air filter becomes clogged by dust or the like, internal temperatures rise, which could cause a fire, a burn or malfunction to the projector. When the indicators or a message prompts you to clean the air filter, comply with it as soon as possible. Note that the projector may shut down, when the projector heats too much. Please replace the air filter when it is damaged or too soiled.
Maintenance Air filter (continued) Turn the projector on and reset the filter time using the FILTER TIME item in the EASY MENU (25). 9. (1) Press the MENU button to display a menu. (2) Point at the “FILTER TIME” using the ▼/▲ button, then press the ► button. A dialog will appear. (3) Press the ▲ button to select “RESET” on the dialog. It performs resetting the filter time.
Maintenance Internal clock battery Consumption of the battery makes the clock not to work correctly. When the clock is wrong or it has stopped, please replace the battery according to the following procedures. 1. 2. 3. Turn the projector off, and unplug the power cord. Allow the projector to cool sufficiently. After making sure that the projector has cooled adequately, slowly turn over the projector, so that the bottom is facing. Battery Cover Remove the battery cover.
Maintenance Other care Inside of the projector In order to ensure the safe use of your projector, please have it cleaned and inspected by your dealer about once every year. Caring for the lens If the lens is flawed, soiled or fogged, it could cause deterioration of display quality. Please take care of the lens, being cautious of handling. Turn the projector off, and unplug the power cord. Allow the projector to cool sufficiently.
Troubleshooting Troubleshooting Related messages When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please follow the instructions described below. If the same message is displayed after the remedy, or if a message other than the following appears, please contact your dealer or service company.
Troubleshooting Regarding the indicator lamps Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the table below. Please follow the instructions within the table. If the same indication is displayed after the remedy, or if an indication other than the following is displayed, please contact your dealer or service company.
Troubleshooting Regarding the indicator lamps (continued) POWER LAMP TEMP indicator indicator indicator Description The cooling fan is not operating. Blinking In Red or Lighting In Red Turned off Blinking In Red Please turn the power off, and allow the projector to cool down at least 20 minutes. After the projector has sufficiently cooled down, please make confirmation that no foreign matter has become caught in the fan, etc., and then turn the power on again.
Troubleshooting Phenomena that may be easy to be mistaken for machine defects WARNING ►Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact your dealer or service company.
Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Phenomenon Cases not involving a machine defect The signal cables are not correctly connected. Correctly connect the audio cables. The MUTE function is working. Sound does not come out. Restore the sound pressing the MUTE or VOLUME button on the remote control. The volume is adjusted to an extremely low level. Adjust the volume to a higher level using the menu function or the remote control.
Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Phenomenon Cases not involving a machine defect The brightness and/or contrast are adjusted to an extremely low level. Adjust BRIGHTNESS and/or CONTRAST settings to a higher level using the menu function. Pictures appear dark. The WHISPER function is working. Select NORMAL for the WHISPER item in the SETUP menu. The lamp is approaching the end of its product lifetime. Replace the lamp.
Warranty And After-Service / Specification Warranty and after-service If a problem occurs with the equipment, first refer to the “Troubleshooting” and run through the suggested checks. If this does not resolve the problem, please contact your dealer or service company. They will tell you what warranty condition is applied. Specification Item Product name Liquid Crystal Panel Panel size Specification Liquid crystal projector 2.0 cm (0.
Specifications 319 Specifications (continued) 154 139 418 [unit: mm] 69
Projector 8918/8943 User's Manual – Operating Guide Technical Example of computer signal Resolution (H x V) H. frequency (kHz) V. frequency (Hz) 720 x 400 640 x 480 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1152 x 864 1280 x 960 1280 x 1024 1280 x 1024 1280 x 1024 1600 x 1200 1280 x 768 1400 x 1050 37.9 31.5 37.9 37.5 43.3 35.2 37.9 48.1 46.9 53.7 49.7 48.4 56.5 60.0 68.7 67.5 60.0 64.0 80.0 91.1 75.0 47.7 65.
Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu. Back porch (B) Front porch (D) Back porch (b) Display interval (C) Data H. Sync. Data V. Sync. Sync (A) Computer/ Horizontal signal timing (μs) Signal (A) (B) (C) (D) TEXT 2.0 3.0 20.3 1.0 VGA (60Hz) 3.8 1.9 25.4 0.6 VGA (72Hz) 1.3 4.1 20.3 0.8 VGA (75Hz) 2.0 3.8 20.3 0.
Connection to the ports Connection to the ports C A RGB OUT AUDIO IN 1 AUDIO IN 2 RGB1 Y VIDEO LAN B D RGB2 M1-D CB/PB CR/PR S-VIDEO R AUDIO IN 3 L REMOTE CONTROL (3.5Φ) AUDIO OUT R L AUDIO IN 4 CONTROL A RGB IN1, B RGB IN2, C RGB OUT AC IN D-sub 15pin mini shrink jack • Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive) • H/V. sync. Signal: TTL level (positive/negative) • Composite sync.
Connection to the ports (continued) LAN RGB OUT I VIDEO AUDIO IN 1 AUDIO IN 2 Y E F RGB1 RGB2 G M1-D CB/PB CR/PR H S-VIDEO R AUDIO IN 3 L R L AUDIO IN 4 AUDIO OUT REMOTE CONTROL (3.5Φ) COMPONENT VIDEO E Y, F CB/PB, G CR/PR CONTROL AC IN RCA jack x3 I O • System: 525i(480i), 525p(480p), 625i(576i), 750p(720p), 1125i(1080i) Port Signal Y Component video Y, 1.0±0.1Vp-p, 75Ω terminator with composite CB/PB Component video CB/PB, 0.7±0.1Vp-p, 75Ω terminator CR/PR Component video CR/PR, 0.
Connection to the ports (continued) LAN J K RGB OUT VIDEO AUDIO IN 1 AUDIO IN 2 S-VIDEO RGB1 Y L R AUDIO IN 3 RGB2 M1-D CB/PB M L N O R L AUDIO IN 4 R Q P CR/PR REMOTE CONTROL (3.5Φ) AUDIO OUT CONTROL AC IN J AUDIO IN 1, K AUDIO IN 2 Ø3.5 stereo mini jack • 500 mVrms 47kΩ terminator I O AUDIO IN 3 L R, M L, AUDIO IN 4 N R, O L RCA jack x2 • 500 mVrms 47kΩ terminator P AUDIO OUT Ø3.5 stereo mini jack • 500 mVrms 1kΩ output impedance Q REMOTE CONTROL Ø3.
Connection to the ports (continued) S RGB OUT RGB1 Y VIDEO AUDIO IN 1 AUDIO IN 2 LAN RGB2 M1-D CB/PB CR/PR S-VIDEO R AUDIO IN 3 L R L AUDIO IN 4 REMOTE CONTROL (3.
RS-232C Communication RS-232C Communication 1 2 6 3 7 4 8 5 1 2 6 9 CONTROL port RS-232C cable (Cross) of the projector - (1) RD (2) TD (3) - (4) GND (5) - (6) RTS (7) CTS (8) - (9) (1) CD (2) RD (3) TD (4) DTR (5) GND (6) DSR (7) RTS (8) DTS (9) RI 3 7 4 8 5 9 RS-232C port of the computer Connecting the cable Turn off the projector and the computer. 1. Connect the CONTROL port of the projector with a RS-232C port of 2. the computer by a RS-232C cable (cross).
RS-232C Communication (continued) Requesting projector status (Get command) (1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes)+ ‘00H’ +‘00H’) from the computer to the projector. (2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer. Changing the projector settings (Set command) (1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) + setting code (2 bytes)) from the computer to the projector.
RS-232C Communication (continued) Names Power Input Source Operation Type Set Set Error Status BRIGHTNESS BRIGHTNESS Reset CONTRAST CONTRAST Reset PICTURE MODE Set GAMMA Set Turn off Turn on Get RGB1 RGB2 M1-D VIDEO S-VIDEO COMPONENT Get Get Get Increment Decrement Execute Get Increment Decrement Execute NORMAL CINEMA DYNAMIC BOARD(BLACK) BOARD(GREEN) WHITEBOARD Get #1 DEFAULT #1 CUSTOM #2 DEFAULT #2 CUSTOM #3 DEFAULT #3 CUSTOM #4 DEFAULT #4 CUSTOM #5 DEFAULT #5 CUSTOM Get Header BE EF 03 03
RS-232C Communication (continued) Names User Gamma Pattern Operation Type Set User Gamma Point 1 User Gamma Point 2 User Gamma Point 3 User Gamma Point 4 User Gamma Point 5 User Gamma Point 6 User Gamma Point 7 User Gamma Point 8 COLOR TEMP COLOR TEMP GAIN R COLOR TEMP GAIN G 10 Set Header CRC Action Command Data Type Setting Code Off BE EF 03 06 00 FB FA 01 00 80 30 00 00 9 step gray scale BE EF 03 06 00 6B FB 01 00 80 30 01 00 15 steps gray scale BE EF 03
RS-232C Communication (continued) Names Operation Type COLOR TEMP GAIN B COLOR TEMP OFFSET R COLOR TEMP OFFSET G COLOR TEMP OFFSET B COLOR Header CRC Action Command Data Type Setting Code Get BE EF 03 06 00 8C F5 02 00 B3 30 00 00 Increment BE EF 03 06 00 EA F5 04 00 B3 30 00 00 Decrement BE EF 03 06 00 3B F4 05 00 B3 30 00 00 Get BE EF 03 06 00 04 F5 02 00 B5 30 00 00 Increment BE EF 03 06 00 62 F5 04 00 B5 30 00 00 Decrement B
RS-232C Communication (continued) Names ASPECT Operation Type Set OVER SCAN OVER SCAN Reset V POSITION V POSITION Reset H POSITION H POSITION Reset H PHASE H SIZE H SIZE Reset AUTO ADJUST COLOR SPACE Set COMPONENT Set C-VIDEO FORMAT Set S-VIDEO FORMAT Set 12 Header CRC Action Command Data Type Setting Code 4:3 16:9 14:9 SMALL NORMAL Get Get Increment Decrement Execute BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF 03 03 03 03 03 03 03 03 03 03 06 00 06 00 06
RS-232C Communication (continued) Names Operation Type M1-D Set RGB 1 Set RGB 2 Set FRAME LOCK Set KEYSTONE V KEYSTONE V Reset KEYSTONE H KEYSTONE H Reset ACTIVE IRIS Set WHISPER Set MIRROR Set VOLUME-RGB1 VOLUME-RGB2 VOLUME-M1-D VOLUME-Video VOLUME-S-Video Header CRC Action Command Data Type Setting Code NORMAL ENHANCED Get SYNC ON G OFF SYNC ON G ON Get SYNC ON G OFF SYNC ON G ON Get BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF 03 03 03 03 03 03 03 03 03 06
RS-232C Communication (continued) Names Operation Type VOLUME-Component TREBLE-RGB1 TREBLE-RGB2 TREBLE-M1-D TREBLE-Video TREBLE-S-Video TREBLE-Component BASS-RGB1 BASS-RGB2 BASS-M1-D BASS-Video BASS-S-Video BASS-Component SRS WOW RGB1 Set CRC Action Command Data Type Setting Code Get BE EF 03 06 00 01 CC 02 00 65 20 00 00 Increment BE EF 03 06 00 67 CC 04 00 65 20 00 00 Decrement BE EF 03 06 00 B6 CD 05 00 65 20 00 00 Get BE EF 03 06 00 0D
RS-232C Communication (continued) Names SRS WOW RGB2 Operation Type Set Set Set Set BE EF 03 06 00 CE FE 01 00 94 20 00 00 03 06 00 AE FF 01 00 94 20 02 00 HIGH BE EF 03 06 00 3E FF 01 00 94 20 03 00 BE EF 03 06 00 FD FE 02 00 94 20 00 00 TURN OFF BE EF 03 06 00 BA FF 01 00 93 20 00 00 MID BE EF 03 06 00 DA FE 01 00 93 20 02 00 HIGH BE EF 03 06 00 4A FF 01 00 93 20 03 00 BE EF 03 06 00 89 FF 02 00 93
RS-232C Communication (continued) Names Operation Type AUDIO - M1-D Set AUDIO - Video Set AUDIO - S-Video Set AUDIO - Component Set IR REMOTE Front Set IR REMOTE Rear Set IR REMOTE Top Set IR REMOTE FREQ. NORMAL Set IR REMOTE FREQ.
RS-232C Communication (continued) Names LANGUAGE Operation Type Set MENU POSITION H MENU POSITION H Reset MENU POSITION V MENU POSITION V Reset BLANK BLANK On/Off START UP My Screen LOCK MESSAGE Set Set Set Set Set Header CRC Action Command Data Type Setting Code ENGLISH BE EF 03 06 00 F7 D3 01 00 05 30 00 00 FRANÇAIS BE EF 03 06 00 67 D2 01 00 05 30 01 00 DEUTSCH BE EF 03 06 00 97 D2 01 00 05 30 02 00 ESPAÑOL BE EF 03 06 00 07 D3 01 00 0
RS-232C Communication (continued) Names AUTO SEARCH Operation Type Set AUTO OFF AUTO ON Set Header CRC Action Command Data Type Setting Code TURN OFF BE EF 03 06 00 B6 D6 01 00 16 20 00 00 TURN ON BE EF 03 06 00 26 D7 01 00 16 20 01 00 Get BE EF 03 06 00 85 D6 02 00 16 20 00 00 Get BE EF 03 06 00 08 86 02 00 10 31 00 00 Increment BE EF 03 06 00 6E 86 04 00 10 31 00 00 Decrement BE EF 03 06 00 BF 87 05 00 10 31 00 00 TUR
RS-232C Communication (continued) Names MY BUTTON-2 Operation Type Set MAGNIFY FREEZE Set Header CRC Action Command Data Type Setting Code RGB1 BE EF 03 06 00 C6 32 01 00 01 36 00 00 RGB2 BE EF 03 06 00 06 30 01 00 01 36 04 00 M1-D BE EF 03 06 00 36 32 01 00 01 36 03 00 COMPONENT BE EF 03 06 00 96 31 01 00 01 36 05 00 S-VIDEO BE EF 03 06 00 A6 33 01 00 01 36 02 00 VIDEO BE EF 03 06 00 56 33 01 00 01 36 01 00 INFORMATION BE EF 03 06 0
Projector 8918/8943 User’s Manual – Network Functions This manual is only intended to explain Network Functions. For safety, operations or any other issues, refer to the all user's manual for this projector. WARNING • Before using the network functions, read the all the manual sections for this projector carefully to ensure your projector is set up correctly. • After reading, keep the manuals in a safe place for future reference. NOTE • The information in this manual is subject to change without notice.
Network Functions Network Functions This projector is equipped with the following network functions. Configuring and Controlling the Projector via a Web Browser You can change the settings of or control the projector via a network by using a web browser from a PC that is connected to the same network. (4) Failure & Warning Alerts via E-mail The projector can automatically send an alert to specified e-mail addresses when the projector requires maintenance or has encountered an error.
Network Functions Before using the network functions… To use the network functions of this projector, the projector must be configured to suit your network. Consult with your network administrator before connecting the projector to your network. Incorrect network configuration of this projector may cause problems on your network.
Network Functions Configuring and controlling the projector via a web browser You can adjust or control the projector via a network from a web browser on a PC that is connected to the same network. NOTE • Internet Explorer 5.5 or higher or Netscape 6.2 or higher are required. • If JavaScript is disabled in your web browser configuration, you must enable JavaScript in order to use the projector web pages properly. See the Help files for your web browser for details on how to enable JavaScript.
Network Functions Configuring and controlling the projector via a web browser (Continued) When configuring or controlling the projector via a web browser, an ID and password are required. There are two types of IDs, Administrator IDs and User IDs. The following chart describes the differences between user and administrator IDs. Item Description Displays the projector’s current Network Information network configuration settings.
Settings Settings Refer to the following for configuring or controlling the projector via a web browser. Example: If the IP address of the projector is set to 192.168.1.10: 1) Enter [https://192.168.1.10] into the address bar of the web browser and the screen in Fig. 1 will be displayed. 2) Enter your ID and password and click [Logon]. Fig. 1 If the logon is successful either the Fig.2 or Fig.3 screen will be displayed. Fig. 2 (Logon with administrator ID) Fig.
Settings Network Information All screen images displayed in this manual are screens of a logon using an administrator ID. Any administrator only functions will not be displayed when using a user ID. Refer to the descriptions in each table. Displays the projector’s current network configuration settings. Item Description DHCP Displays the DHCP configuration settings. IP Address Displays the current IP address. Subnet Mask Displays the Subnet Mask. Default Gateway Displays the Default Gateway.
Settings Network Settings Displays and configures network settings. Item IP Configuration Description Configures network settings. DHCP ON Enables DHCP. DHCP OFF Disables DHCP. IP Address Configures the IP address when DHCP is disabled. Subnet Mask Configures the Subnet Mask when DHCP is disabled. Default Gateway Configures the Default Gateway when DHCP is disabled. Projector Name Configures the Projector name. SysLocation Configures the location to be referred to when using SNMP.
Settings Port Settings Displays and configures communication port settings. Item Network Control Port1 (Port:23) Description Configures command control port 1 (Port:23). Port open Click the [Enable] check box to use port 23. Authentication Click the [Enable] check box when authentication is required for this port. Network Control Port2 (Port:9715) Configures command control port 2 (Port:9715). Port open Click the [Enable] check box to use port 9715.
Settings Mail Settings Displays and configures e-mail addressing settings. Item Description Send Mail Click the [Enable] check box to use the e-mail function. Configure the conditions for sending email under [Alert Settings]. SMTP Server IP Address Configures the address of the mail server in IP format. Sender E-mail address Configures the sender e-mail address. The length of the sender e-mail address can be up to 255 alphanumeric characters.
Settings Alert Settings Displays and configures failure & warning alerts. Item Cover Error Description Configures Cover Error alert settings. SNMP Trap Click the [Enable] check box to enable SNMP Trap alerts for this item. Send Mail Click the [Enable] check box to enable e-mail alerts for this item. Mail Subject Configures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters. Mail Text Configures the text of the e-mail to be sent.
Settings Alert Settings (Continued) Item Lamp Error Configures Lamp Error alert settings. SNMP Trap Click the [Enable] check box to enable SNMP Trap alerts for this item. Send Mail Click the [Enable] check box to enable e-mail alerts for this item. Mail Subject Configures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters. Mail Text Configures the text of the e-mail to be sent.
Settings Alert Settings (Continued) Item Lamp Time Error Description Configures Lamp Time Error alert settings. SNMP Trap Click the [Enable] check box to enable SNMP Trap alerts for this item. Send Mail Click the [Enable] check box to enable e-mail alerts for this item. Mail Subject Configures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters. Mail Text Configures the text of the e-mail to be sent.
Settings Alert Settings (Continued) Item Other Error Description Configures Other Error alert settings. SNMP Trap Click the [Enable] check box to enable SNMP Trap alerts for this item. Send Mail Click the [Enable] check box to enable e-mail alerts for this item. Mail Subject Configures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters. Mail Text Configures the text of the e-mail to be sent.
Settings Alert Settings (Continued) Item Filter Time Alarm Description Configures Filter Time Alarm alert settings. Alarm Time Configures the filter time to alert. SNMP Trap Click the [Enable] check box to enable SNMP Trap alerts for this item. Send Mail Click the [Enable] check box to enable e-mail alerts for this item. Mail Subject Configures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters.
Settings Schedule Settings Displays and configures schedule settings. Item Daily Configures the daily schedule. Schedule Click the [Enable] check box to enable daily scheduling. Schedule List Displays the current daily schedule. Sunday Configures the Sunday schedule. Schedule Click the [Enable] check box to enable Sunday scheduling. Schedule List Displays the current Sunday schedule. Monday Configures the Monday schedule. Schedule Click the [Enable] check box to enable Monday scheduling.
Settings Schedule Setting (Continued) Item Specific date No1 Description Configures the specific date (No.1) schedule. Schedule Click the [Enable] check box to enable specific date (No.1) scheduling. Month/Day Configures the Month and date. Schedule List Displays the current specific date (No.1) schedule. Specific date No.2 Configures the specific date (No.2) schedule. Schedule Click the [Enable] check box to enable specific date (No.2) scheduling. Month/Day Configures the Month and date.
Settings Schedule Setting (Continued) To add additional functions and events click the [Add] button and set the following items. Item Description Time Configures the time to execute commands. Command Configures the commands to be executed. Power Parameter Configures the parameters for power control. Input Source Parameter Configures the parameters for input switching. Display Image Parameter Configures the parameters for display of transfer image data.
Settings Date/Time Settings (Continued) Item Daylight Savings Time Start Description Click the [ON] check box to enable daylight savings time and set the following items. Configures the date and time daylight savings time begins. Month Configures the month daylight savings time begins (1~12). Week Configures the week of the month daylight savings time begins (First, 2, 3, 4, Last). Day Configures the day of the week daylight savings time begins (Sun, Mon, Tue, Wed, Thu, Fri, Sat).
Settings Security Settings Displays and configures passwords and other security settings. Item Administrator authority Description Configures the Administrator ID and Password. Administrator ID Configures the Administrator ID. The length of the text can be up to 32 alphanumeric characters. Administrator Password Configures the Administrator Password. The length of the text can be up to 255 alphanumeric characters. Re-enter Administrator Re-enter the above password for verification.
Settings Security Settings (Continued) Item Network Control Authentication Password Description Configures the Authentication Password for the command control. Configures the Authentication Password. The length of the text can be up to 16 alphanumeric characters. Re-enter Authentication Used to re-enter the above password for verification. Password SNMP Community Name Configures the community name if SNMP is used. Configures the community name.
Projector Control Projector Control Projector Control The items shown in the table below can be performed using the [Projector Control] menu. Select an item using the up and down arrow keys on the PC. Most of the items have a submenu. Refer to the table below for details. Controls the projector. Item Description Main Power Turns the power On/Off. Input Source Selects the input source. Picture Mode Selects the Picture Mode setting. Blank On/Off Turns Blank On/Off. Mute Turns Mute On/Off.
Projector Control Projector Control (Continued) Item Description Image Aspect Selects the Aspect setting. Over Scan Selects the Over Scan setting. V Position Adjusts the V Position. H Position Adjusts the H Position. H Phase Adjusts the H Phase. H Size Adjusts the H Size. Auto Adjust Performs Auto Adjustment. Input Progressive Selects the progressive setting. Video NR Selects the Video NR setting. 3D-YCS Selects the 3D-YCS setting. Color Space Selects the Color Space.
Projector Control Projector Control (Continued) Item Description Audio Volume Adjusts the Volume setting. Treble Adjusts the Treble setting. Bass Adjusts the Bass setting. SRS WOW Selects the SRS WOW setting. Speaker Turns Speaker On/Off. Audio-RGB1 Assigns the Audio-RGB1 input terminal. Audio-RGB2 Assigns the Audio-RGB2 input terminal. Audio-M1-D Assigns the Audio-M1-D input terminal. Audio-Video Assigns the Audio-Video input terminal.
Projector Control Projector Status Displays and configures the current projector status. Item Description Error Status Displays the current error status Lamp Time Displays the usage time for the current lamp. Filter Time Displays the usage time for the current filter. Power Status Displays the current power status. Input Status Displays the current input signal source. Blank On/Off Displays the Blank On/Off status. Mute Displays the current Mute On/Off status.
Failure & Warning Alerts via E-mail Failure & Warning Alerts via E-mail The projector can automatically send an alert to specified e-mail addresses when the projector requires maintenance or has encountered an error. NOTE • Up to five e-mail addresses can be specified. • The projector may be not able to send e-mail if the projector suddenly loses power. Mail Settings (10) To use the projector’s e-mail function please configure the following items via a web browser.
Failure & Warning Alerts via E-mail Mail Settings (Continued) 8) Configure the Failure/Warning Alerts via E-mail settings. Click [Alert Settings] on the main menu. 9) Select and configure each alert item. Refer to [Alert Settings] in [Configuring and Controlling the Projector via a Web Browser] for further information. 10) Click the [Apply] button to save the settings.
Projector management via SNMP Projector management via SNMP When SNMP is enabled, the projector is able to send Failure/Warning Alerts to a specified PC. NOTE • It is recommended that SNMP functions be carried out by a network administrator. • SNMP management software must be installed on the computer to monitor the projector via SNMP. SNMP settings (9) Configure the following items via a web browser to use SNMP. Example: If the IP address of the projector is set to 192.168.1.10: 1) Enter [https://192.
Controlling the Projector via Scheduling Controlling the Projector via Scheduling The projector can be automatically controlled via scheduling. NOTE • You can schedule the following control events: Power ON/OFF, Input Source and Transferred Image Display. • There are 3 types of Scheduling, 1) daily 2) day of the week 3) specific date. • The priority for scheduled events is as follows 1) specific date 2) day of the week 3) daily. • Up to five specific dates are available for scheduled events.
Controlling the Projector via Scheduling Date/Time Settings (18) The Date/Time setting can be adjusted via a web browser. Example: If the IP address of the projector is set to 192.168.1.10: 1) Enter [https://192.168.1.10] into the address bar of the web browser. Enter the Administrator ID and Password and click [Logon]. 2) Click [Date/Time Settings] on the main menu and configure each item.
Controlling the Projector via Scheduling Schedule Settings (16) Schedule settings can be configured from a web browser. Example: If the IP address of the projector is set to 192.168.1.10: 1) Enter [https://192.168.1.10] into the address bar of the web browser. 2) Enter the Administrator ID and Password and click [Logon]. 3) Click [Schedule Settings] on the main menu and select the required schedule item. 4) Click the [Enable] check box to enable scheduling.
e-SHOT (Still Image Transfer) Display e-SHOT (Still Image Transfer) Display The projector can display a still image that is transferred via the network. Communication Port The following port is used for e-SHOT. TCP #9716 (9) NOTE • e-SHOT is not available via communication ports which are used for the command control (TCP #23 and TCP #9715). e-SHOT (Still Image Transfer) Settings Configure the following items from a web browser when e-SHOT is used.
e-SHOT(Still Image Transfer) Display e-SHOT (Still Image Transfer) Settings (Continued) When the authentication setting is enabled, the following settings are required. 6) Click [Security Settings] on the main menu. 7) Select [Network Control] and enter the desired authentication password. * see Note1 8) Click the [Apply] button to save the settings.
Command Control via the Network Command Control via the Network You can configure and control the projector via the network using RS-232C commands. Communication Port The following two ports are assigned for the command control. TCP #23 TCP #9715 NOTE • Command control is not available via communication port (TCP #9716) that is used for the e-SHOT transmission function. Command Control Settings (9) Configure the following items from a web browser when command control is used.
Command Control via the Network Command Control Settings (Continued) When the authentication setting is enabled, the following settings are required. (20) 7) Click [Security Settings] on the main menu. 8) Click [Network Control] and enter the desired authentication password. * See Note1. 9) Click the [Apply] button to save the settings. * See Note2.
Command Control via the Network Command format Command formats differ among the different communication ports. TCP #23 You can use the RS-232C commands without any changes. The reply data format is the same as the RS-232C commands. However, the following reply will be sent back in the event of authentication failure when authentication is enabled.
Command Control via the Network Reply Data format The connection ID (the data is same as the connection ID data on the sending data format) is attached to the RS-232C commands reply data.
Command Control via the Network Automatic Connection Break The TCP connection will be automatically disconnected after there is no communication for 30 seconds after being established. Authentication The projector does not accept commands without authentication success when authentication is enabled. The projector uses a challenge response type authentication with an MD5 (Message Digest 5) algorithm. When the projector is using a LAN, a random eight bytes will be returned if authentication is enabled.
Read this Safety Guide first. Projector User's Manual - Safety Guide Thank you for purchasing this projector. WARNING • Before using, read these user's manuals of this projector to ensure correct usage through understanding. After reading, store them in a safe place for future reference. Incorrect handling of this product could possibly result in personal injury or physical damage.
Safety Precautions WARNING Never use the projector if a problem should occur. Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. can cause a fire or electrical shock. In such case, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact your dealer.
Safety Precautions (continued) WARNING Be cautious of High temperatures of the projector. High temperatures are generated when the lamp is lit. It could result in fire or burn. Use special caution in households where children are present. Do not touch about the lens, air fans and ventilation openings during use or immediately after use, to prevent a burn. Take care of ventilation. • Keep a space of 30 cm or more between the sides and other objects such as walls.
Safety Precautions (continued) WARNING Be careful in handling the light source lamp. The projector uses a high-pressure mercury glass lamp made of glass. The lamp can break with a loud bang, or burn out. When the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes. Please carefully read the section “Lamp”. Be careful in handling the power cord and external connection cables.
Safety Precautions (continued) CAUTION Be careful in moving the projector. Neglect could result in an injury or damage. • Do not move the projector during use. Before moving, disconnect the power cord and all external connections, and close the slide lens door or attach the lens cap. • Avoid any impact or shock to the projector. • Do not drag the projector. • For moving the projector, use the enclosed case or bag if provided. Do not put anything on top of the projector.
Safety Precautions (continued) CAUTION Remove the power cord for complete separation. • For safety purposes, disconnect the power cord if the projector is not to be used for prolonged periods of time. • Before cleaning, turn off and unplug the projector. Neglect could result in fire or electrical shock. Disconnect the plug from the power outlet. Ask your dealer to cleaning inside of the projector about every year. Accumulations of dust inside the projector cause result in fire or malfunction.
Safety Precautions (continued) NOTE About consumables. Lamp, LCD panels, polarizors and other optical components, and air filter and cooling fans have a different lifetime in each. These parts may need to be replaced after a long usage time. • This product isn’t designed for continuous use of long time.
Lamp WARNING HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.
Regulatory Notices FCC Statement Warning WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Audio Visual Products 2900 Dukane Drive St. Charles, Illinois 60174 www.dukcorp.com/av Toll-free: 800-676-2487 Fax: 630-584-5156 e-mail: avsales@dukcorp.
