Camera 220E Document Camera User’s Guide #401-220E-01
Table of Contents TABLE OF CONTENTS ......................................................................................... 1 COPYRIGHT INFORMATION ................................................................................ 2 CHAPTER 1 PRECAUTIONS ................................................................................ 3 CHAPTER 2 PACKAGE CONTENT ......................................................................4 CHAPTER 3 PRODUCT OVERVIEW .................................................
Chapter 1 Precautions Always follow these safety instructions when setting up and using the Digital Presenter: 1. Do not place the Digital Presenter on an unstable trolley, stand or table. 2. Do not use the Digital Presenter near water or source of heat. 3. Use attachments only as recommended. 4. Use the type of power source indicated on the Digital Presenter. If you are not sure of the type of power available, consult your dealer or local electricity company for advice. 5.
Safety Precautions Warning: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. This Digital Presenter has a 2 wires AC line Plug. This is a safety feature to ensure that the plug will fit into the power outlet. Do not try to defeat this safety feature. If the Digital Presenter will not be used for an extended time, unplug it from the power outlet. CAUTION RISK OF ELECTRIC SHOCK Caution: To reduce the risk of electric shock. Do not remove cover (or back).
Chapter 2 Package Content Please make sure the package comes with the following items when you unpack: Camera 220C User’s Manual CD Power Cable USB Cable C-Video Cable VGA Cable DVI Adapter Remote Controller 4
Chapter 3 Product Overview 3.
3.2 I/O Connection IR Control Input IR Control Input 3.5 mm Mini 3.
3.4 Infrared Remote Control 3 2 1 12 4 5 11 6 10 7 8 9 1. Power: Turn on/ off. 2. Capture: Capture the image. 3. Freeze: Freeze the image. 4. Arrows: You may press the 4 hot keys of Up/Down/Right/Left to go to the desired function item then press the Enter key to take effect. Different color contrast modes. 8. Lamp: Turn on/ off Lamp. 9. Play & Del: Play press, you can recall the saved images in the flash memory of your Digital Presenter. Press Del if you would like to discard the saved image.
3.5 IR Remote Control via 3.5 mm Mini Connector The IR commands from a protocol converter can be sent directly to an IR emitter located behind the dark window on the front of the camera. This permits the camera to be controlled as part of a system without the necessity of attaching external IR emitters. The 3.5 mm mini connector on the body, “IR Control Input,” is connected internally to an IR emitter located near the detector. This detector can receive the IR signals from the emitter.
Chapter 4 How to use it This chapter describes the basic and advanced functions of the Digital Presenter, how to use the OSD (On Screen Display) menu. 4.1 Getting Started 4.1.1 Turn on the Digital Presenter. ¾ Option 1: Press button. ¾ Option 2: Press button of remote controller. 4.1.2 Lens focus ¾ Turn the lens to optimize the focus 4.1.3 Zoom in / Out ¾ Press the control button 4.1.4 Switch source ¾ Press to Choose signal source between Camera 220E or PC. That signal is sent to the projector.
4.1.5 Photo/Text: ¾ Press to Select the text or photo mode. 4.1.6 Enter AWB (Auto White Balance) ¾ press to set the auto white balance. 4.1.7 Capture Image & Review of captured images ¾ How to capture an image Method 1:Press on the remote to capture image that you would like to save. Method 2:Follow the steps using the pad buttons on the Camera. 2.1 First, press to go to the OSD (On Screen Display). 2.
1.1 First, press button to go to OSD interface. 1.2 Second, press ^ v to select the "storage" Then select “Playback”, and press icon, and press , so you can see all captured thumbnail images on the screen. 1.3 You can press button to select the image which you want to magnify. (Enlarge to full screen) Then press , the image will appear full screen. Method 2: Using the Remote Control: Method 2: Using the Remote Control: 2.
3.2 Press ^ v to select the "Storage" press icon and . Then select “Playback”, and press , so you can see all captured thumbnail images on the screen. 3.3 Then, press button to select the thumbnail image which you want to magnify and press , the image will show full screen. 4.2 Showing the OSD (On Screen Display) Menu ¾ Option 1: Press button to show the OSD Menu ¾ Option 2: Press button of remote control. 4.
4.4 OSD Menu Introduction The fiveicons, icons The and functions detail functions will be explained in TheMain MainMenu Menucontaining contains five are shown in the following table. next page. Setting Display Source Storage Exit ¾ VGA Mode (Computer Image) Layer 1 Setting Layer 2 Layer 3 Function Lamp On / Off / Exit Select Lamp On or Off. Night view On/Off Select Night view function On or Off.
Brightness 0-46 (for PAL) Brightness adjustment 0-40 ( for NTSC) Display Zoom Digital Zoom Adjust Zoom 100% ~ 1600%. (100% to 1600%) Gamma Photo / Text Select Photo/Text Mode. Image Normal / Gray / Film Select Normal/Gray/Film Mode. Flip On/Off Adjust the image up and down by 180°. Freeze On/Off Use Freeze to retain the image on the screen. Exit Exit this menu. Presenter Select images of Presenter or VGA Input. VGA In Source Storage Capture Capture the image of Presenter.
VIDEO Mode (For NTSC, lower resolution) Layer 1 Layer 2 Layer 3 Function Brightness 0-46 (for PAL) Brightness adjustment 0-40 ( for NTSC) Display Gamma Photo/Text Image Normal/Gray Freeze On/Off Exit Lamp On/Off Night view On /off Exit Setting Language Factory Reset Exit Select Normal/Gray Mode. Use Freeze to retain the image on the screen. Exit this menu. Full Range On/off Advance Select Photo/Text Mode.
Chapter 5 Using the Camera USB with a Computer Installation 1. Insert the software CD in your computer’s CD-ROM. 2. Connect the Camera and PC with USB Cable . Follow instructions for driver download. 3. Before you install MR2004, please be sure your system meets these requirements. • Operation System • Windows XP • Windows 2000 • ME • 98 • 98SE • CPU • Intel Pentium II • CD ROM or DVD ROM • 64MB RAM • Minimum 40MB HD space 350MHz over and above 4.
3. 5. The installation wizard is shown, please press Next to go next. 6. While the License Agreement picture is shown, select 『I accept the terms in the 4. license agreement 』and press Next to go next.
5. 7. Click Next difference. 6. 8. Please press to install from the default folder or click Install Change to specify a to begin installation. 7. 9. The installation is processing, if you would like to cancel, please press Cancel to stop installation.
8. Please press 10. Finish to complete the installation.
9. After installation, the MR2004 is launched automatically or you may go to the PC “Start”, 11. and look at “All Programs” to find MR2004. Functions This chapter will introduce all functions of MR2004, the user interface of MR2004 as below.
The Tool Bar Functions are described. 1. File z New:Open new project(file format-- *.mr2) z Open:Open old project in stored file z Save:Save present edited project z Save As:Save to be a new project or given file z Save Image:Save reedited JPG image z Import From Device:Import an image from memory device (Only for certin devices.) z Export to PPT: Export the image to be Power Point file format z Language:Select English, Traditional Chinese, Simplify Chinese user interface. 2.
3. Edit mode Functions in this mode are File, Paint tool and Full screen. The Freeze and capture are not available in edit mode. The lower Preview window tool bar appears for the Edit mode. 4. Freeze The image can be frozen in real time mode. (*This function is only available in real time mode) 5. Capture You can capture images which are saved as JPG files in the default folder is C:\Program File\MR2004\, (* This function is only available in real time mode.) 6.
In the "Edit Mode" the lower Preview Area images can be selected using the "Page Up" or The picture be change on the screen with “Page up“or”Page Down” button. "Page Down"can button. 8.Import from device ( ) This function does not operate with the Camera. Please ignor. One image can be captured in the MR2004 via CPT-I connection device of MH400 that is more efficiency then “capture” function in real time mode. 9. Image beforehand view tool :Insert a picture from image file. Bring in picture from file.
O Cperation 1 Choose Language: FILE Æ Language , there are 3 language for selection:English & Traditional-Chinese and Simplify-Chinese, please choose 「English」. 2 Display image: 2.1 Real Time Operation:Import a line image from Camera. Document Camera) 2.2 Import From Device,:Import images from Camera. May not always be operative. device. 2.3 Edit model open old file,:Use preview tool( )to open an old file in edit mode..
3 Edit image: 3.1 Marking:Click any tool in the paint tool menu to modiy the image.
3.2 Edited and save:After editing pictures, click the small picture icon in the preview area, and then save the picture. Click the small picture 4 After Save: 4.1 Save MR2004 file:Save as “*.m2” file format to C:\Program Files\MR2004 4.2 Export to PPT format:After editing and arranging images, the function can export to power point file.
Chapter 5 Troubleshooting If none of the suggested solutions solves the problem, call your dealer or your service center. Problem 1: No picture from the Camera. Solution 1: Wait a few seconds, press desired source selector again. 2: Press a different source, then press-desired source again. 3: Check if the power is turned on. (Pilot Light On?) 4: Make sure the document or object is positioned under the camera. 5.
Audio Visual Products 2900 Dukane Drive St. Charles, Illinois 60174 www.dukcorp.com/av Toll-free: 800-676-2487 Fax: 630-584-5156 e-mail: avsales@dukcorp.