series PROPANE CONSTRUCTION HEATER USER’S MANUAL AND OPERATING INSTRUCTIONS MODELS: LPFA40WH LPFA60WH LPFA125WH LPFA150WH (40,000 BTU/HR, FORCED - AIR) (30,000/60,000 BTU/HR, FORCED - AIR) (70,000/125,000 BTU/HR, FORCED - AIR) (120,000/150,000 BTU/HR, FORCED - AIR) C US ANS Z83.7-2011 CSA 2.14-2011 Adequate ventilation must be provided.
PROPANE CONSTRUCTION HEATER TABLE OF CONTENTS Introduction & Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 • General Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 • Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 • Unpacking Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PROPANE CONSTRUCTION HEATER PROPANE FORCED AIR CONSTRUCTION HEATERS The heater is designed and approved for use as a construction heater under ANS Z83.7 CSA 2.14. It is hard to anticipate every use which may be made of this heater. CHECK WITH YOUR LOCAL FIRE SAFETY AUTHORITY IF YOU HAVE QUESTIONS ABOUT APPLICATIONS. Other standards govern the use of fuel gases and heat producing products in specific applications. Your local authority can advise you about these.
PROPANE CONSTRUCTION HEATER GENERAL SAFETY INSTRUCTION Accidents are always tragic especially because so many of them could have been prevented with little care and judgment. There are some basic good practices, we hope you will follow for safe use of your heater. IMPORTANT SAFETY INSTRUCTION • Children should be carefully supervised, when they are in the area. • Always maintain proper clearance from combustible materials.
PROPANE CONSTRUCTION HEATER UNPACKING HEATER 1. Remove heater from carton. 2. Remove all protective packing applied to heater for shipment. 3. Retain cartons and packaging material until unit is operated and found in good condition. 4. Check heater for any shipping damage. If heater shows any external or internal damage, promptly inform dealer/distributor where you purchased heater.
PROPANE CONSTRUCTION HEATER INFORMATION ON SIZE * CAPACITY OF PROPANE GAS CYLINDERS: The chart below shows the number and size of propane tanks needed to run this heater. *Less gas is vaporized at lower temperatures. You may need two or more 100 pound (45 kg) tanks or one larger tank in colder weather. (See the parts list for your model of heater to get the specified regulator assembly.
PROPANE CONSTRUCTION HEATER INSTALLATION TO THE PROPANE GAS TANK IMPORTANT: You must use a propane/LP gas supply cylinder that is compatible with the connection device provided with the hose and regulator. Propane/LP Supply Valve Propane/LP Tank Regulator Fuel Gas Fitting Hose to Heater Hose to Regulator Hose Fitting FIGURE 2 FIGURE 1 FIGURE 3 Connector Inlet 1. Provide propane/LP supply system. Ensure that the valve on the cylinder is fully closed by turning the knob fully clockwise ( ).
PROPANE CONSTRUCTION HEATER PROPANE SAFETY Propane is safe to use when properly handled. Careless handling of the Propane gas tank could result in fire and/or an explosion. Therefore: • Always keep tank/cylinder securely fastened in an upright position. • Avoid tipping tank on its side when connected to a regulator since this may cause damage to diaphragm in regulator. • Handle valves with care. • Never connect an unregulated Propane tank to construction heater.
PROPANE CONSTRUCTION HEATER SHUTDOWN INSTRUCTIONS WARNING : Motor and fan must be running before lighting, during operation and at shutdown, in order to prevent a flame-out condition which could result in personal injury or property damage. Turn gas valve knob clockwise to OFF position. Turn gas supply OFF by turning Propane tank valve clockwise to close. Disconnect the power cord once the heater has cooled to ambient temperature.
PROPANE CONSTRUCTION HEATER TROUBLESHOOTING TROUBLESHOOTING: PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION 1. Control dial is off and unit is clicking/4cking 1. This heater uses a con4nuous spark igni4on system. This unit will con4nue to make a clicking/4cking sound at all 4mes before igni4on, aAer igni4on and during opera4on, regardless of valve knob posi4oning. 1. No correc4ve ac4on is needed.
PROPANE CONSTRUCTION HEATER WIRING DIAGRAMS NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! 11
PROPANE CONSTRUCTION HEATER WIRING DIAGRAMS *100K,125K & 150K Models only *100K,125K & 150KSólo modelos *100K,125K & 150K Les modèles Seulement * ** 12 NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
PROPANE CONSTRUCTION HEATER REPLACEMENT PARTS LIST MODELS: LPFA40WH LPFA60WH NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! 13
PROPANE CONSTRUCTION HEATER REPLACEMENT PARTS LIST PART NUMBER ITEM No. DESCRIPTION QTY 1 2 3 4 5 6 7 8 9 10 11 12 12.1 12.2 12.3 13 13.1 13.2 14 14.
PROPANE CONSTRUCTION HEATER PROPANE CONSTRUCTION HEATER ILLUSTRATED / PARTS BREAKDOWN MODELS: LPFA125WH LPFA150WH NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! 15
PROPANE CONSTRUCTION HEATER REPLACEMENT PARTS LIST PART NUMBER ITEM No. 1 2 3 4 5 6 7 8 9 10 11 12 12.1 12.2 12.3 13 13.1 13.2 14 14.
WARRANTY LIMITED WARRANTY: This limited warranty is extended to the original retail purchaser of this Forced Air/Convection/Radiant Heater and warrants against any defect in materials and workmanship for a period of one (1) year from the date of retail sale. GHP Group, Inc., at it’s option, will either provide replacement parts or replace or repair the unit, when properly returned to the retailer where purchased or one of our service centers as directed by GHP Group, Inc.
WARRANTY REGISTRATION IMPORTANT: We urge you to fill out your warranty registration card within fourteen (14) days of date of purchase. You can also register your warranty on the internet at www.ghpgroupinc.com. Complete the entire serial number. Retain this portion of the card for your records. GHP Group, Inc. 6440 W Howard GHP Group, Inc. St Niles, IL 60714-3302 GHP 8280 Austin Ave. Morton Grove, IL 60053-3207 Tel: (877) 447-4768 www.ghpgroupinc.com Tel: (877) 447-4768 www.ghpgroupinc.
series RADIATEUR DE CONSTRUCTION AU GAZ PROPANE MANUEL DE L’USAGER ET INSTRUCTIONS D’OPÉRATION LPFA40WH LPFA60WH LPFA125WH LPFA150WH MODÈLE: (40,000 BTU/HR, FORCED - AIR) (30,000/60,000 BTU/HR, FORCED - AIR) (70,000/125,000 BTU/HR, FORCED - AIR) (120,000/150,000 BTU/HR, FORCED - AIR) C US ANS Z83.7-2011 CSA 2.14-2011 Une ventilation adéquate est nécessaire.
RADIATEUR DE CONSTRUCTION AU GAZ PROPANE TABLE DES MATIÈRES Introduction et caractéristiques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 • Instructions de sûreté générales . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 • Caractéristiques du produit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 • Déballage du radiateur . . . . . . . . . . . . . . .
RADIATEUR DE CONSTRUCTION AU GAZ PROPANE RADIATEUR DE CONSTRUCTION AU GAZ PROPANE À AIR FORCÉ L’appareil de chauffage est conçu et approuvé pour être utilisé comme radiateur de construction en vertu de la norme ANS Z83.7 CSA 2.14. Il est difficile de prévoir toutes les utilisations qui peuvent être faites de ce radiateur. VEUILLEZ CONSULTER LES AUTORITÉS LOCALES EN MATIÈRE DE SÉCURITÉ INCENDIE SI VOUS AVEZ DES QUESTIONS AU SUJET DES APPLICATIONS POSSIBLES.
RADIATEUR DE CONSTRUCTION AU GAZ PROPANE CONSIGNES DE SÉCURITÉ GÉNÉRALES Les accidents sont toujours tragiques, surtout parce que bon nombre d’entre eux pourraient être évités avec un peu d’attention et de jugement. Il existe quelques bonnes pratiques de base que vous devez suivre pour une utilisation sécuritaire de votre radiateur. CONSIGNES DE SÉCURITÉ IMPORTANTES • Surveillez attentivement les enfants lorsqu’ils se trouvent dans la zone chauffée.
RADIATEUR DE CONSTRUCTION AU GAZ PROPANE DÉBALLAGE 1. Retirez l’appareil de chauffage de la boîte. 2. Retirez tout emballage de protection appliqué au radiateur pour l’expédition. 3. Conservez les cartons et matériaux d’emballage jusqu’à ce que l’appareil soit mis en marche et que son bon état de fonctionnement soit constaté. 4. Vérifiez que le radiateur n’a pas été endommagé durant le transport.
RADIATEUR DE CONSTRUCTION AU GAZ PROPANE INFORMATION SUR LA TAILLE * CAPACITÉ DES BONBONNES DE GAZ PROPANE Le tableau ci-dessous indique le nombre et le format des bouteilles de gaz propane nécessaires pour faire fonctionner ce radiateur. *À des températures inférieures, une quantité moindre de gaz est dégagée.Par temps froid, vous pourriez avoir besoin de deux bouteilles (ou plus) de 45 kilos (100 livres) ou d’une plus grosse bouteille.
RADIATEUR DE CONSTRUCTION AU GAZ PROPANE INSTALLATION À LA BOUTEILLE DE GAZ PROPANE IMPORTANT: Vous devez utiliser une bouteille de gaz propane (pétrole liquéfié) qui est compatible avec le dispositif de raccord fourni avec le tuyau et le régulateur.. Vanne d’alimentation en propane (pétrole liquéfié). Bouteille de propane (pétrole liquéfié) Régulateur Vanne d’alimentation en propane (pétrole liquéfié).
RADIATEUR DE CONSTRUCTION AU GAZ PROPANE SÉCURITÉ RELATIVE AU PROPANE Le propane est sécuritaire lorsqu’il est manipulé correctement. Une manipulation négligente du réservoir de gaz propane peut entraîner un incendie et (ou) une explosion. Par conséquent : • Gardez toujours le réservoir (la bouteille), solidement fixé en position verticale. • Évitez de pencher le réservoir sur le côté lorsqu’il est connecté à un régulateur, car cela pourrait endommager la membrane du régulateur.
RADIATEUR DE CONSTRUCTION AU GAZ PROPANE DIRECTIVES D’ARRÊT AVERTISSEMENT : Le moteur et le ventilateur doivent être en marche avant l’allumage, pendant le fonctionnement de l’appareil et à l’arrêt, afin de prévenir une extinction accidentelle qui pourrait causer des blessures ou entraîner des dommages matériels. Tournez le bouton de commande du gaz dans le sens horaire jusqu’à la position D’ARRÊT .
RADIATEUR DE CONSTRUCTION AU GAZ PROPANE DÉPANNAGE TROUBLESHOOTING: PROBLÈME CAUSES POSSIBLES MESURE CORRECTIVE 1. Le cadran de réglage est éteint et l’unité émet un clique4s. 1. Ce1e situa4on est normale. Ce radiateur u4lise un système d’allumage par é4ncelle con4nu. Ce1e unité émet constamment un clique4s, que ce soit avant ou après l’allumage ou durant le. 1.
RADIATEUR DE CONSTRUCTION AU GAZ PROPANE DIAGRAMMES DES CÂBLES NE LAISSEZ JAMAIS L’APPAREIL DE CHAUFFAGE ALLUMÉ SANS SURVEILLANCE! 11
RADIATEUR DE CONSTRUCTION AU GAZ PROPANE DIAGRAMMES DES CÂBLES 100K,125K & 150K Models 100K,125K & 150K Les modèles 100K,125K & 150K modelos NE LAISSEZ JAMAIS L’APPAREIL DE CHAUFFAGE ALLUMÉ SANS SURVEILLANCE! 12
RADIATEUR DE CONSTRUCTION AU GAZ PROPANE DÉTAIL ILLUSTRÉ DES PIÈCES D’UN APPAREIL DE CHAUFFAGE À GAZ PROPANE POUR LA CONSTRUCTION MODÈLE: LPFA40WH LPFA60WH NE LAISSEZ JAMAIS L’APPAREIL DE CHAUFFAGE ALLUMÉ SANS SURVEILLANCE! 13
RADIATEUR DE CONSTRUCTION AU GAZ PROPANE LISTE DES PIÈCES DE RECHANGE NUMERO DE PIECE Article No.
RADIATEUR DE CONSTRUCTION AU GAZ PROPANE DÉTAIL ILLUSTRÉ DES PIÈCES D’UN APPAREIL DE CHAUFFAGE À GAZ PROPANE POUR LA CONSTRUCTION MODÈLE: LPFA125WH LPFA150WH NE LAISSEZ JAMAIS L’APPAREIL DE CHAUFFAGE ALLUMÉ SANS SURVEILLANCE! 15
RADIATEUR DE CONSTRUCTION AU GAZ PROPANE LISTE DES PIÈCES DE RECHANGE Article No. 1 2 3 4 5 6 7 8 9 10 11 12 12.1 12.2 12.3 13 13.1 13.2 14 14.
GARANTIE
GHP Group, Inc. 6440 W Howard St Niles, IL 60714-3302 Tel: (877) 447-4768 www.ghpgroupinc.com GHP Group, Inc.
series CALENTADOR DE PROPANO PARA CONSTRUCCIÓN MANUAL DEL USUARIO E INSTRUCCIONES DE OPERACIÓN MODELOS: LPFA40WH LPFA60WH LPFA125WH LPFA150WH (40,000 BTU/HR, FORCED - AIR) (30,000/60,000 BTU/HR, FORCED - AIR) (70,000/125,000 BTU/HR, FORCED - AIR) (120,000/150,000 BTU/HR, FORCED - AIR) C US ANS Z83.7-2011 CSA 2.14-2011 Se debe proporcionar la ventilación adecuada.
CALENTADOR PARA CONSTRUCCIÓN A PROPANO ÍNDICE • Introducción y especificaciones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 • Instrucciones generales de seguridad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 • Características del producto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 • Desempacado del calentador . . . . . . . . . . . . . . . .
CALENTADOR DE PROPANO PARA CONSTRUCCIÓN CALENTADORES DE AIRE FORZADO CON PROPANO PARA CONSTRUCCIÓN El calentador está diseñado y aprobado para su uso como calentador para construcción bajo ANS Z83.7 CSA 2.14. Es difícil anticipar cada uso que se le puede dar a este calentador. REVISE CON LAS AUTORIDADES DE PREVENCIÓN DE INCENDIOS LOCALES SI TIENE PREGUNTAS ACERCA DE LAS APLICACIONES. Hay otras normas que rigen el uso de gases combustibles o de productos que generan calor en aplicaciones específicas.
CALENTADOR DE PROPANO PARA CONSTRUCCIÓN INSTRUCCIONES GENERALES DE SEGURIDAD Los accidentes son trágicos siempre, especialmente porque muchos de ellos pudieron haberse prevenido con un poco de cuidado y juicio. Hay algunas buenas prácticas básicas y esperamos que las siga para un uso seguro de su calentador. INFORMACIÓN IMPORTANTE DE SEGURIDAD • Se debe supervisar cuidadosamente a los niños cuando estén en el área • Mantenga siempre un resguardo considerable de los materiales combustibles.
CALENTADOR DE PROPANO PARA CONSTRUCCIÓN DESEMPACADO 1. Saque el calentador de la caja. 2. Retire todos los empaques protectores que se le colocan al calentador al embarcarlo. 3. Conserve las cajas y los materiales de empaque hasta que éste esté funcionando y se encuentre en buenas condiciones. 4. Revise si el calentador no se dañó durante el envío. Si el calentador muestra cualquier daño externo o interno, informe de inmediato al comerciante o distribuidor donde lo compró.
CALENTADOR DE PROPANO PARA CONSTRUCCIÓN INFORMACIÓN DE TAMAÑO * Y CAPACIDAD DE LOS CILINDROS DE PROPANO: La siguiente tabla muestra el número y el tamaño de los tanques de propano necesarios para que el calentador funcione. *El gas se vaporiza menos a temperaturas más bajas. Usted puede necesitar dos o más tanques de 100 libras (45 kg) o un tanque grande en tiempo de frío.
CALENTADOR DE PROPANO PARA CONSTRUCCIÓN INSTALACIÓN DEL TANQUE DE GAS PROPANO IMPORTANTE: Usted debe utilizar un tanque de abastecimiento de gas propano (LP) que sea compatible con el dispositivo de conexión que se proporciona con la manguera y el regulador.
CALENTADOR DE PROPANO PARA CONSTRUCCIÓN SEGURIDAD DEL GAS PROPANO El gas propano es seguro cuando se maneja de manera apropiada. La falta de cuidado en el manejo del tanque de gas puede causar un incendio o explosión. Por lo tanto: • Mantenga el tanque siempre sujetado de manera segura en posición vertical. • Evite inclinar el tanque cuando lo conecte a un regulador, ya que esto puede causar daños al diafragma en el regulador. • Maneje las válvulas con cuidado.
CALENTADOR DE PROPANO PARA CONSTRUCCIÓN INSTRUCCIONES DE APAGADO ADVERTENCIA : El motor y el abanico deben estar en funcionamiento antes de encender el calentador, durante la operación y también al apagarlo, esto para prevenir que salga alguna flama y cause heridas corporales o daños a la propiedad. Gire la perilla de la válvula de gas hacia la derecha a la posición de APAGADO . Gire el abastecimiento de gas a APAGADO dando vuelta a la válvula del tanque hacia la derecha para cerrar.
CALENTADOR DE PROPANO PARA CONSTRUCCIÓN TROUBLESHOOTING: DIAGNÓSTICO Y RESOLUCIÓN DE PROBLEMAS PROBLEMA CAUSA POSIBLE ACCIÓN CORRECTIVA 1. La perilla de control está apagada y la unidad hace chasquidos. 1. Esto es normal. Este calentador u5liza un sistema 1. No se necesitan acciones correc5vas. de encendido con5nuo.
CALENTADOR DE PROPANO PARA CONSTRUCCIÓN DIAGRAMAS DE CABLEADO ¡NUNCA DEJE EL CALENTADOR DESATENDIDO CUANDO ESTÉ ENCENDIDO! 11
CALENTADOR DE PROPANO PARA CONSTRUCCIÓN DIAGRAMAS DE CABLEADO *100K,125K & 150K Models only *100K,125K & 150KSólo modelos *100K,125K & 150K Les modèles Seulement * ** ¡NUNCA DEJE EL CALENTADOR DESATENDIDO CUANDO ESTÉ ENCENDIDO! 12
CALENTADOR DE PROPANO PARA CONSTRUCCIÓN DESGLOSE ILUSTRADO DE PIEZAS DEL CALENTADOR A GAS PROPANO PARA CONSTRUCCIÓN: MODELOS: LPFA40WH LPFA60WH ¡NUNCA DEJE EL CALENTADOR DESATENDIDO CUANDO ESTÉ ENCENDIDO! 13
CALENTADOR DE PROPANO PARA CONSTRUCCIÓN LISTA DE PARTES DE REEMPLAZO Artículo No. 1 2 3 4 5 6 7 8 9 10 11 12 12.1 12.2 12.3 13 13.1 13.2 14 14.
CALENTADOR DE PROPANO PARA CONSTRUCCIÓN DESGLOSE ILUSTRADO DE PIEZAS DEL CALENTADOR A GAS PROPANO PARA CONSTRUCCIÓN: MODELOS: LPFA125WH LPFA150WH ¡NUNCA DEJE EL CALENTADOR DESATENDIDO CUANDO ESTÉ ENCENDIDO! 15
CALENTADOR DE PROPANO PARA CONSTRUCCIÓN LISTA DE PARTES DE REEMPLAZO Artículo No. 1 2 3 4 5 6 7 8 9 10 11 12 12.1 12.2 12.3 13 13.1 13.2 14 14.
GARANTÍA GARANTÍA LIMITADA: Esta garantía limitada es extendida al comprador original al detalle de este Calentador de Aire Forcado/ Convección/ Radiante y garantiza contra cualquier defecto en materiales y funcionamiento por un período de un (1) año desde la fecha de venta al detalle. GHP Group,Inc.
REGISTRO DE GARANTÍA IMPORTANTE: Lo invitamos a completar nuestro formulario de registro de garantía dentro de los siguientes 14 días a la fecha de compra. Usted también puede registrar su garantía en el internet en www.ghpgroupinc.com. Complete el número de serie. Conserve esta parte de la tarjeta como su comprobante. GHP Group, Inc. 6440 W Howard GHP Group, Inc. St Niles, IL 60714-3302 8280 Austin Ave. Morton Grove, IL 60053-3207 GHP Tel: (877) 447-4768 www.ghpgroupinc.com Tel: (877) 447-4768 www.