Instructions / Assembly

2-Inch nylon garage door roller
dlr13
InstallatIon InstructIons
1. Close door completely. Keep door closed by fasten-
ing “C” clamps on both the left and right door track
against the top side of two rollers.
2. Disconnect power and lifting arm of garage door
opener.
3. (FOR TOP ROLLERS GO TO STEP 4) Unbolt hinge from
door. Feed roller into new hinge tube furthest from
door. Place roller wheel into track and bolt hinge to
door. Replace and tighten one hinge at a time before
proceeding to the next step.
4. For Top Rollers only-install an additional “C” clamp in
door track engaged in door so top section of door is
restrained from rotating down when the bracket is
removed. Replace brackets or rollers ONE AT A TIME,
moving “C” clamp or locking pliers to prevent door
section from pivoting. Install roller into bracket and
feed roller into track. Fasten bracket to door and use
adjusting bolt on bracket to snug door against jamb.
tools needed:
Philips screwdriver
Drill
• Read and understand all instruction before you begin work.
• Wear safety goggles and gloves.
• Unplug power door opener and remove opener travel arm from door FIRST.
• Do not remove more than one part at a time.
• Do not attempt to raise or lower door without all components installed and securely tightened.
• Extension and torsion springs, along with attached hardware are under extreme tension at all times.
• All tension must be released from springs before any work is started.
• This hardware is intended for residential garage doors only.
• If you do not completely understand the installation instructions or are unsure whether the replacement
part matches the part to be replaced, contact a professional installer.
WARNING!
IMPROPER INSTALLATION OR DOOR POSITION CAN RESULT IN SERIOUS INJURY OR DEATH.
DURALIFTHARDWARE.COM
TORSION SPRINGS
DASMA WARNING:
HIGH SPRING TENSION CAN CAUSE
SERIOUS INJURY OR DEATH. DO NOT
adjust, repair or remove springs or parts to
which springs are connected, such as steel
brackets, cables, wood blocks, red colored
fasteners or other parts of the counterbalance
system. Adjustments or repairs must ONLY be
made by a trained door systems technician
using proper tools and instructions.
2-Inch nylon garage door roller
dlr13
InstallatIon InstructIons
1. Close door completely. Keep door closed by fasten-
ing “C” clamps on both the left and right door track
against the top side of two rollers.
2. Disconnect power and lifting arm of garage door
opener.
3. (FOR TOP ROLLERS GO TO STEP 4) Unbolt hinge from
door. Feed roller into new hinge tube furthest from
door. Place roller wheel into track and bolt hinge to
door. Replace and tighten one hinge at a time before
proceeding to the next step.
4. For Top Rollers only-install an additional “C” clamp in
door track engaged in door so top section of door is
restrained from rotating down when the bracket is
removed. Replace brackets or rollers ONE AT A TIME,
moving “C” clamp or locking pliers to prevent door
section from pivoting. Install roller into bracket and
feed roller into track. Fasten bracket to door and use
adjusting bolt on bracket to snug door against jamb.
tools needed:
Philips screwdriver
Drill
• Read and understand all instruction before you begin work.
• Wear safety goggles and gloves.
• Unplug power door opener and remove opener travel arm from door FIRST.
• Do not remove more than one part at a time.
• Do not attempt to raise or lower door without all components installed and securely tightened.
• Extension and torsion springs, along with attached hardware are under extreme tension at all times.
• All tension must be released from springs before any work is started.
• This hardware is intended for residential garage doors only.
• If you do not completely understand the installation instructions or are unsure whether the replacement
part matches the part to be replaced, contact a professional installer.
WARNING!
IMPROPER INSTALLATION OR DOOR POSITION CAN RESULT IN SERIOUS INJURY OR DEATH.
DURALIFTHARDWARE.COM