Instructions / Assembly

ManualsBrandsDura-Trel ManualsKitchen85 in. x 72 in. x 30 in. White Vinyl PVC Windsor Arbor

Model#

11112

Assembly Instructions

Part # Description Box#

4" sq. x 84" Left Post

2 4" sq. x 84" Right Post 1

3 2" sq. x 29¾ Top/Bottom Cross Rail 2

4 2" sq. x 29¾ Center Cross Rail 2

5 ⅞ x 1½ x 59½" Vertical Rail 1

6 1½ x 4 x 72" Arbor Top Rail 1

⅞ x 1½ x 72" Arbor Top Overhead Rail

8 2" sq. x 26¾" Arbor Top Cross Rail 1

8 2" sq. x 26¾" Arbor Top Cross Rail 2

9 4" sq. Flat Post Cap 1

10 24" Steel Ground Anchor (U-shaped) 1

11 Hardware Bag

(includes:)

4" End Cap

⅞ x 1½" End Cap

PLEASE READ THROUGH BEFORE BEGINNING ASSEMBLY. 1¼" Painted Screw

IMPORTANT: Check boxes for Contents Listed

#8 - 1" Painted Self Tapping

Check inside of parts as some parts are packaged

Super Glue Tube

inside of others

In the event of missing, damaged or defective parts

please call our customer service dept. at 1-877-258-6020

When assembling components, place on a clean, flat

non-abrasive surface to avoid scratches

…

Battery or Electric Drill with #2 phillips bit

… Tape Measure

…

Hammer or Rubber Mallet (recommended)

…

Shovel or Post Hole Digger (recommended)

150 Birch Road

P.O. Box 122

Sheboygan Falls, WI 53085

Qty

Windsor Arbor

General Information

www.dura-trel.com

sales@dura-trel.com

Tools Required

1-877-258-6020

Summary of content (7 pages)

PAGE 1
Windsor Arbor Model# 11112 Part # General Information PLEASE READ THROUGH BEFORE BEGINNING ASSEMBLY. IMPORTANT: Check boxes for Contents Listed Check inside of parts as some parts are packaged Assembly Instructions Description Box# Qty 1 4" sq. x 84" Left Post 1 2 2 4" sq. x 84" Right Post 1 2 3 2" sq. x 29¾ Top/Bottom Cross Rail 2 4 4 2" sq.
PAGE 2
Warranty Statement 20 Year Guarantee Please call manufacturer direct with questions concerning missing or defective parts at Toll Free: 877-258-6020. Dura-trel, Inc. products are warranted to be free from manufacturing defects resulting in delaminating, peeling, flaking, corroding, cracking, crazing, or extreme amounts of fading or bleaching causing the PVC to change to its natural color for a period of 20 years from the date of purchase.
PAGE 3
1 Lay out one right post (part 2). Starting at bottom, insert one top/bottom rail (part 3) and four center rails (part 4). 2 Slide three vertical rails (part 5) through center rails and into top/bottom rail. 3 Insert one top/bottom rail (part 3) into right post, sliding three vertical rails into top/bottom rail. 4 Slide left post (part 1) over corresponding top/bottom and center rails. DO NOT screw arbor panel together. REPEAT steps 1-4 for the second arbor panel.
PAGE 4
5 With arbor panels lying down and screw pilot holes of each arbor panel facing out, slide two arbor top rails (part 6) all the way through both routed holes at the top of each arbor panel. Note: 2” sq. holes should line up with 2” sq. holes in the top of the arbor panels. This will leave 7” of overhang on each side of the arbor. 6 Insert five arbor top cross rails (part 8) into arbor top rails and arbor panel posts by carefully separating posts just enough to insert the five rails.
PAGE 5
8 9 Using 1½” kappet screws, insert screws through holes of two overhead rails (part 7). Fasten screws to screw pilot holes of the five arbor top cross rails. Snap kappet screw caps over screw heads. Apply PVC glue to inner edges of the four flat post caps (part 9) and place on top of each post. Glue four 4” arbor top end caps onto ends of each arbor top rail. Glue four overhead rail end caps onto ends of each overhead rail.
PAGE 6
ARBOR INSTALLATION Option 1 Slide one 24” steel u-channel ground anchor (part 10) into bottom of each post. Slide ground anchor until it meets bottom cross rail. Using 1” self-tapping white-head screw fasten post to ground anchor. Using ground anchor installation layout drawing, dig holes approximately 16” deep. Set arbor in holes and level. Back fill with soil removed from holes. For permanent installation fill with cement.
PAGE 7
11112 1 2 3 4 5 6 7 8 9 10 11 Windsor Arbor 4" sq. x 84" WDA Left Post 4" sq. x 84" WDA Right Post 2" sq. x 29¾ WD Top/Bottom R 2" sq. x 29¾ WD Center Rail ⅞ x 1½ x 59½" Rail - Thin 1½ x 4 x 72" WDA Arbor Top ⅞ x 1½ x 72" WDA Overhead R 2" sq. x 26¾ CYA Top Cross R 24" Steel Grnd Anch (U-shaped) 4" sq." Flat Cap Hardware Bag ⅞ x 1½" End Cap 1¼" Painted Screw #8 - 1" Self Tapping White He PVC Glue 2.00 2.00 4.00 8.00 6.00 2.00 2.00 5.00 4.00 4.00 1.00 4.00 26.00 8.00 1.