Replacement Part List

ManualsBrandsDura-Trel ManualsOutdoors6 ft. White Vinyl Patio Picnic Table

Model#

11114

Assembly Instructions

Part # Description Box#

1 1½ x 5½ x 72" Table Rail 1

2 1½ x 5½ x 72" Seat Rail 2

3 1½ x 5½ x 59½" Cross Brace 1

1½ x 5½ x 30¼" Leg 2

5 25½" Table Bracket 2

6 8¾" Seat Bracket 2

7 ⅞ x 1½ x 27" Center Brace 2

8 ⅞ x 1½ x 26½" Diagonal Brace 2

9 28" Table End Cap 2

10 11 ⅛" Seat End Cap 2

11 6 ⅛" Leg End Cap 2

12 5½" Cross Brace End Cap 2

13 Hardware Bag

(includes:)

⅞ x 1½" End Cap

PLEASE READ THROUGH BEFORE BEGINNING ASSEMBLY. ¾" Screw

IMPORTANT: Check boxes for Contents Listed

1½" Screw

Check inside of parts as some parts are packaged

¼ x 3½" Bolt

inside of others

¼ x 2¼" Bolt

¼" Nylock Nut

In the event of missing, damaged or defective parts

¼" Flat Washer

please call our customer service dept. at 1-877-258-6020

Super Glue Tube

When assembling components, place on a clean, flat

non-abrasive surface to avoid scratches

…

Battery or Electric Drill with #2 phillips bit, ¼", ⅛" drill bits

… Two 7/16" wrenches or sockets

… Tape Measure

… File

115 Vision Parkway

P.O. Box 122

Sheboygan Falls, WI 53085

www.dura-trel.com

sales@dura-trel.com

Tools Required

1-877-258-6020

General Information

Qty

6' Picnic Table

Summary of content (6 pages)

PAGE 1
6' Picnic Table Model# General Information Part # 1 2 3 4 5 6 7 8 9 10 11 12 13 11114 Assembly Instructions Description 1½ x 5½ x 72" Table Rail 1½ x 5½ x 72" Seat Rail 1½ x 5½ x 59½" Cross Brace 1½ x 5½ x 30¼" Leg 25½" Table Bracket 8¾" Seat Bracket ⅞ x 1½ x 27" Center Brace ⅞ x 1½ x 26½" Diagonal Brace 28" Table End Cap 11 ⅛" Seat End Cap 6 ⅛" Leg End Cap 5½" Cross Brace End Cap (includes:) Hardware Bag Box# 1 2 1 2 2 2 2 2 2 2 2 2 2 Qty 2 4 2 4 2 4 1 2 2 4 4 4 1 ⅞ x 1½" End Cap 2 ¾" Screw 72
PAGE 2
Warranty Statement 20 Year Guarantee Please call manufacturer direct with questions concerning missing or defective parts at Toll Free: 877-258-6020. Dura-trel, Inc. products are warranted to be free from manufacturing defects resulting in delaminating, peeling, flaking, corroding, cracking, crazing, or extreme amounts of fading or bleaching causing the PVC to change to its natural color for a period of 20 years from the date of purchase.
PAGE 3
TABLE TOP ASSEMBLY Lay out five 72" table top rails (part 1) as shown above with pilot holes facing up. Table top rails have two holes in the center of each rail, seat rails do not. Set two 25½" table brackets (part 5) over pilot holes at each end of table top rail, leaving ⅛" gap between rails. Using twenty ¾" screws per bracket, fasten each bracket to table top rails. Apply glue to inner edges of ⅞ x 1½" end cap (from hardware bag) and press on each end of 27" center brace (part 7).
PAGE 4
SEAT ASSEMBLY Lay out two 72" seat rails (part 2) with pilot holes facing up. Seat rails do no have any holes in the center of each rail. Set two 8¾" seat brackets (part 6) over pilot holes at each end of seat rail, leaving ⅛" gap between rails. Using eight ¾" screws per bracket, fasten each bracket to seat rails. Apply glue to inside edges of 11⅛" seat end cap (part 10). Press end cap onto ends of seat (DO NOT slide from end).
PAGE 5
CROSS BRACE / LEG ASSEMBLY Lay out two 30¼" legs (part 4) on an angle with pre-drilled holes for attaching table top, nearest each other at top. Lay one 59½" cross brace (part 3) across legs; adjusting legs so bolt holes line up. Using four 3½" botls, eight washers and four nuts, fasten cross brace to legs. (Do not over tighten as this will crush the vinyl) Bolt heads will face outside of the table. Apply glue to inside edges of 5½" cross brace end cap (part 12).
PAGE 6
Insert one cross brace / leg assembly into brackets on underside of table top with cross brace closest to table end. Using four 2¼" bolts, washers and nuts, fasten assembly to table top. Repeat with second cross brace / leg assembly for opposite end of table. Using one 2¼" bolt, washers and nut, bolt one 26½" diagonal brace (part 8) to center of each cross brace. In center of table, overlap free ends of diagonal braces and drill two ⅛" holes through braces and into center brace.