Instructions / Assembly

ManualsBrandsDura-Trel ManualsStorage & Organization8 ft. x 9.5 ft. Queensbrook Resin Pergola

Model#

11301

Assembly Instructions

Part # Description Box#

1 4" sq. x 93" Post 1

1½ x 5½ x 106" Bottom Support Rail

3 1½ x 5½ x 106" Upper Support Rail 2

4 ⅞ x 3 x 106" Top Cross Rail 2

1½" Upper Support Bracket 3

6 4" sq. New England Post Cap 3

7 1½ x 5½" Pergola End Cap 3

8 24" Ground Anchor (U-shaped) 1

9 Hardware Bag

(includes:)

⅞ x 3" End Cap

2" Painted Screw

¾" Painted Screw

PLEASE READ THROUGH BEFORE BEGINNING ASSEMBLY. #8 - 1" Painted Self Tapping Screw

IMPORTANT: Check boxes for Contents Listed

(for ground anchors)

Check inside of parts as some parts are packaged

PVC Glue Can

inside of others

In the event of missing, damaged or defective parts

please call our customer service dept. at 1-877-258-6020

or e-mail sales@dura-trel.com

When assembling components, place on a clean, flat

non-abrasive surface to avoid scratches

…

Battery or Electric Drill with #2 phillips bit

… Tape Measure

…

Hammer or Rubber Mallet (recommended)

…

Shovel or Post Hole Digger (recommended)

150 Birch Road

P.O. Box 122

Sheboygan Falls, WI 53085

www.dura-trel.com

sales@dura-trel.com

Tools Required

1-877-258-6020

General Information

102

Qty

Queensbrook Pergola

Summary of content (6 pages)

PAGE 1
Queensbrook Pergola Model# Part # 1 2 3 4 5 6 7 8 9 General Information PLEASE READ THROUGH BEFORE BEGINNING ASSEMBLY. IMPORTANT: Check boxes for Contents Listed Check inside of parts as some parts are packaged 11301 Assembly Instructions Description Box# 4" sq. x 93" Post 1 1½ x 5½ x 106" Bottom Support Rail 2 1½ x 5½ x 106" Upper Support Rail 2 ⅞ x 3 x 106" Top Cross Rail 2 1½" Upper Support Bracket 3 4" sq.
PAGE 2
Warranty Statement 20 Year Guarantee Please call manufacturer direct with questions concerning missing or defective parts at Toll Free: 877258-6020. Dura-trel, Inc. products are warranted to be free from manufacturing defects resulting in delaminating, peeling, flaking, corroding, cracking, crazing, or extreme amounts of fading or bleaching causing the PVC to change to its natural color for a period of 20 years from the date of purchase.
PAGE 3
1 Lay out one lower support rail(part 2). [Lower support has eight pilot holes drilled in top edge] Using ¾" painted screws, fasten four upper support brackets (part 5) to lower support. 2 Insert ends of lower support rails through bottom routed holes of two posts (part 1). Do not screw together at this time. REPEAT steps 1 and 2 using remaining lower support, upper support brackets and posts. 3 Instruction Text Inset ends of two upper support rails (part 3) through top routed holes of posts.
PAGE 4
Lay two top cross rails (part 4) onto the upper supports. To set width of pergola, line up outer most pilot holes of upper supports. Using 2" painted screws, fasten top rails to upper supports. 5 6 Using 2" painted screws, screw together all posts and supports. Slide four remaining upper support rails (part 3) through upper support brackets, underneath top rails.
PAGE 5
7 Using 2" painted screws, fasten top cross rails to upper supports. [This will center remainig upper supports.] 8 9 Using 2" screws, fasten remaining top cross rails (part 4) to upper supports. Using PVC glue provided, glue posts caps (part 6) to top of posts. Glue pergola end caps (part 7) to ends of the upper and lower supports. Last, glue on the ⅞ x 3" end caps to top cross rails.
PAGE 6
PERGOLA INSTALLATION Option 1 10 Slide one 24” ground anchor (part 8) into bottom of each post. Slide ground anchor about 12 inches into post, leaving 18 inches for in-ground. Using 1” painted self-tapping screws fasten post to ground anchor. Dig holes approximately 18 inches deep. Set pergola in holes and level. Back fill with soil removed from holes. For permanent installation fill with cement. Option 2 Pound ground anchors into ground according to dimensions.