The Leader in Event Critical Timing Electronics Model 3220 Series Timer SBD Soap Box Derby Finish Differential & ET Timer Owner’s Manual Rev M RaceAmerica Corporation P.O. Box 3469 Santa Clara, CA 95055-3469 USA (408) 988-6188 http://www.raceamerica.com info@raceamerica.com Copyright 2008 RaceAmerica Corporation.
RaceAmerica Model 3220 Timer SBD Table of Contents LIMITED WARRANTY.........................................................................................................................3 PACKAGE COMPONENTS..................................................................................................................4 POWER REQUIREMENTS...................................................................................................................4 PRODUCT SPECIFICATIONS..............................
RaceAmerica Model 3220 Timer SBD AMERICA RACE T i m i n g S y s t e m s LIMITED WARRANTY To the original purchaser of this RaceAmerica product, RaceAmerica warrants it to be in good working order for a period of ninety (90) days from the date of purchase from RaceAmerica or an authorized RaceAmerica distributor.
RaceAmerica Model 3220 Timer SBD PACKAGE COMPONENTS Each 3220 Series Timer SBD timing system package includes: 1 - 3220D Series Console Unit 1 - IR Beam Emitter Model 5042 2 - IR Track Sensors Model 5140 1 - Interconnect Cable Assembly for Track Sensors & Win Lights (option) 3 - Foam Stands (7540) 1 - 12VDC Power Patch Cord 1 - Owners Manual POWER REQUIREMENTS You will need these additional items to operate your 3220 Series timing system: 1 - 12VDC automotive battery for Console 4 - ‘C’ batteries for Beam
RaceAmerica Model 3220 Timer SBD SET-UP STEPS - 3220 SERIES STEP 1 Familiarize yourself with the components pictured in this manual and how they interconnect. The Track Sensor Interconnect Cable is configured for connection between the a Sensors, Win Lights and timer console at the finish line with a tail for a Start Sensor. All connectors are keyed for proper orientation.
RaceAmerica Model 3220 Timer SBD Emitter Sensor The Emitter throws a spot light like beam of infrared light; the Sensor should be aligned near the center of the beam for optimal reception and alignment. Interconnect Cable to the Timer Console and the Track Sensors through the opening in the back of the Foam Stand. If adding the ET option, see instructions for this option in the options section. STEP 4 Cable tails are available to connect optional Win Lights and Elapsed Time (ET) detection if available.
RaceAmerica Model 3220 Timer SBD until the alignment starts counting determines the maximum vertical detection angle. Once these extremes are established, position the Beam Emitter in the center of the left/right detection angle and up/down detection angle. Repeat this same process with the Track Sensors. This will maximize the alignment accuracy. It should also be noted that once the zero digit has stated counting, it will never stop at zero again unless Alignment Mode is exited and reentered.
RaceAmerica Model 3220 Timer SBD TIMING A RUN - Finish Differential Before timing a run, it may be desireable to enter the racer numbers so they will appear on the printout. To enter a racer number, press the [9] CAR# button on the keypad to view the existing entries; press [9] again to enter new numbers; press [#] ENTER to accept the entries. To time a run, press the [2] RESET button. The timer immediately checks all track sensors to insure they are operating and aligned properly.
RaceAmerica Model 3220 Timer SBD SYSTEM OPTIONS Several options (Elapsed Time (ET), Printer, Digital Display or PC) can be connected by a RS232 cable connection up to 100 feet or by a Wireless Link for greater distances (line of sight up to a quarter mile). Connectors are on the underside of the console. ELAPSED TIME OPTION The Elapsed Time option involves running a cable to the starting line connected to the RaceAmerica starting line connector in the wiring harness.
RaceAmerica Model 3220 Timer SBD MAINTENANCE The 3220 Series Console, Beam Emitter, and Track Sensors do not require any maintenance. To insure uninterrupted operation on raceday, it is suggested to keep track of battery usage hours so as to have fully charged batteries. Plan to replace the ‘C’ cells in the Beam Emitter after about 200 hours use. If you are using rechargeable ‘C’ cells, recharge them each day. Low battery voltage (Emitter voltage below 4.
RaceAmerica Model 3220 Timer SBD 7540C - Foam Stand Assembly Instructions Base Foam Top Foam Emitter Sensor Assembly Components ‘AA’ Battery Emitter (5040B, 5050B & 5058B) 1. Install batteries and turn on the Emitter. 2. Separate the Base of the Foam Stand from the Top. 3. Place the 5040/5050/5058 Emitter into the Base foam with the battery side down. 4. Slide the Top on the Base. Place on the track. Track Sensor (5140D & 5158D) 1. Separate the Base of the Foam Stand from the Top. 2.
RaceAmerica Model 3220 Timer SBD TIMESLIP HEADER The 3220 Console allows custom timeslip header input for four lines of up to 39 characters each to print at the top of each timeslip. Input for the Timeslip Header is found in the [ConFig] [HEAdEr] menu. Once the configuration is input, it is saved until changed or deleted. Input is from the keypad via a two-digit code for each character. The console display prompts for each line, character and character code (existing or new) being input.
Line 1 Line 2 Line 3 Line 4 Character Code Priinted Character Character Code Printed Character Character Code Printed Character Character Code Printed Character Character Position 1 2 3 4 5 6 7 8 9 10 11 13 14 15 16 17 18 19 20 21 22 23 24 25 Timeslip Header Character Code Worksheet 12 26 TIMESLIP LAYOUT WORKSHEET 27 28 29 30 31 32 33 34 35 36 37 38 39 RaceAmerica Model 3220 Timer SBD 13