Product Manual
1100 Amp Li-Ion Jump-Starter
(DRLJS110B/DRBTLC)
IMPORTANT: SAVE THESE INSTRUCTIONS
Misusing or incorrectly connecting the DURACELL
®
Jump-Starter may
damage the equipment or create hazardous conditions for users.
1. Download the PowerHub
™
app
The PowerHub
™
app enables advanced features:
• Battery monitoring and alerts
• Interactive step-by-step guide
• Live support
► Download the app to get started:
DuracellPower.com/App
Scan for app download
2. Product details
1
2
3
4
10
11
9
5 6
7 8
BLUETOOTH
1: Jump-start port
connects
to jump-start clamps.
2: USB port (2.4 Amps)
charges smartphones,
tablets and other devices.
3: Charging ‘IN’ port
connects to USB cable to
recharge the Jump-starter.
4: LED ashlight
features
high beam, low beam and
emergency/SOS mode.
5: Battery level button
and LED gauge
displays
battery charge level.
6: LED status light
bar
indicates state of the
Jump-Starter connection (see
Section 7)
.
7: Light button
activates the
LED ashlight.
8: Bluetooth button
Hold
3 seconds for pairing mode
(requires Duracell Power App).
9: Jump-start clamps
with SafeJump™ feature.
10: Carry bag ts into most
vehicle glove boxes.
11:
DC charger and USB
cable
for recharging the
Jump-Starter.
3. Charging the Jump-starter
WARNING: SHOCK HAZARD
Disconnect jump-start clamps before charging the Jump-starter.
CAUTION
Do not attempt to recharge the Jump-starter battery if it is frozen.
Gradually warm the frozen battery to 32 °F (0 °C) before recharging.
IMPORTANT: FULLY CHARGE BEFORE USE
Prior to using the Jump-starter for the rst time, ensure that the battery of
the Jump-starter is fully charged. If the battery has been fully discharged,
charging with a USB charger may take up to 4 hours.
IMPORTANT: PROPER CHARGER OUTPUT
For fastest possible recharging time, please be sure to use an AC or DC
charger with a rating of 2.0 Amps or higher. The charge times shown
assume the usage of a charger with a 2.0A or higher power rating.
CAUTION
The included DC charger is for charging only Li-Ion type rechargeable
batteries. Other types of batteries may burst causing personal injury or
damage.
A
B
C
► Charging/re-charging the Jump-Starter
Charging times: Partially discharged (or after using jump-starter) -
30-60 minutes; fully discharged jump-starter battery - up to 4 hours
Charging with the included DC charger:
1. Disconnect any cables from the Jump-starter and USB ports.
2. Plug the DC charger into the included 12V vehicle socket (Fig. A) and
connect the small micro USB end of the included USB charging cable to
the ‘IN’ port. (Fig. B)
3. It is best to have the vehicle running while charging.
Charging with an AC charger (sold separately):
1. Disconnect any cables from the Jump-starter and USB ports.
2. Plug the USB cable into your USB wall charger (Fig. C - wall charger
sold separately) and connect the small micro USB end of the included
USB charging cable to the ‘IN’ port (Fig. B).
IMPORTANT
If you keep the Jump-starter in storage, the battery will discharge over
time. Remember to recharge the battery after every use to make sure it is
ready when you need it, and at least once a year. Re-charging more often
will not harm the Jump-starter.
4. Checking the Jump-starter’s battery level
To check the battery’s charge level, press the battery level button on the Jump-
Starter. The LED fuel gauge will illuminate and display the current level of
available battery power. Four lights indicate a 100% charge.
IMPORTANT
Your Jump-starter will perform best when its battery is fully charged. If the
LED Fuel Gauge shows less than 100% charge, it is recommended to fully
recharge its battery (see Section 4: “Charging the Jump-starter” ).
5. Using the LED ashlight and USB port
► Using the LED light
The DURACELL
®
Jump-Starter has a built-in emergency light to provide a safe,
bright work light on the roadside and in other outdoor environments.
Press and release the light button to cycle through the 3 light modes. (High
beam, Low Beam and SOS)
►
Using the USB port
The USB port provides up to 2.4 Amps of current to charge cell phones,
smartphones, tablets and other devices.
1. Open the protective cover over the USB port.
2. Connect your USB device (smartphone, tablet, etc.) to the USB port using
the USB cable supplied with your device.
3. Charging will automatically start.
6. Jump-starting a vehicle
You can use the DURACELL
®
Jump-Starter with the supplied jump-start clamps
to jump-start a vehicle or boat engine. The Jump-Starter is compatible with 12V
vehicles.
WARNING: FIRE HAZARD
Do not crank the engine for more than 4 seconds. The jump-start feature is
designed for short term operation only. Operating the jump-start feature for
more than 4 seconds may cause damage to the unit. Allow the Jump-starter
to cool down for at least 30 seconds after each jump-start.
►
To jump-start a vehicle engine:
1. Connect the jump-start clamps to the Jump-Starter
2. Connect the red (+) clamp to the positive (+) terminal on the vehicle battery
and the black (-) clamp to the negative (-) terminal on the vehicle battery
3. Verify that the Jump-Starter and clamps are clear of any moving engine parts.
4. Start your engine, Be sure to crank for no more than 4 seconds at a time
and allow for 30 seconds in between starting attempts.
5. After starting the vehicle remove the Jump-starter and recharge it.
Red POSITIVE (“+”)
clamp
connects
to
positive
battery
terminal
Black NEGATIVE (“
-
”) clamp
connects to the negative battery
terminal OR
metal part of car
(block, cylinder, etc)
7. Jump-Start LED bar function
Jump-start LED bar Reason and suggestion
OFF No clamp cable connected
Green ash Clamp cable connected, ready to connect to vehicle
Green ash (still ashing after
5 seconds of connection to
battery)
1. Turn off all vehicle accessories and lights; wait 5-10
minutes before reconnecting and try again.
2. If still ashing, the car battery may be below 3V and is
unsafe to use with this jump-starter.
Solid Green Good voltage and polarity - ready to start
Solid Red and beeping
while connecting
Reverse polarity or short - recheck connections
Solid Red - OR - 4 Fuel Gauge
LEDs ashing - After extended
starting
Over temperature - wait for the unit to cool down and reset.
Solid Red + 1 or 2 LED
on fuel gauge
Low internal battery voltage, please fully charge the unit
OFF - after 10 minutes Timed-out for safety, press power button to reset or re-at-
tach red clamp
Green ash after vehicle starts Reverse charge protection - Vehicle started, remove the unit
8. Specications
Electrical specications
Charging Input Voltage/Current 5V/2.0A
DC Adapter Input Voltage 12V
DC Adapter Output Voltage/Current 5V / 2.1 A
Safety certications / efciency certications UL (cTUVus), CEC/BC, FCC
(DC charger: CE,FCC)
Physical specications
Length 7.66 in (19.45 cm)
Width 3.31 in (8.40 cm)
Height 1.40 in (3.55 cm)
Weight (product only) 1.47 lbs (490 g)
9. Important safety instructions
IMPORTANT: Please read these general usage-related warnings and cautions
thoroughly before using this Jump-starter.
WARNING: When using this product, basic
precautions should always be followed, including the
following:
• Read all the instructions before using the product.
• To reduce the risk of injury, close supervision is necessary when the
product is used near children.
• Do not insert ngers or foreign objects into the product.
• Do not use this product with any application of which it was not intended.
• Use of an attachment not recommended or sold by the manufacturer may
result in risk of re, electric shock or injury to persons.
WARNING: Medical equipment
This product is NOT tested, designed nor intended to be used with life
support systems or any other medical devices.
TM