weekendwarrior | Peel & Stick LVT Product Guide
Table of Contents Technical Data Sheet 3 General Information 4 Recommended Tool List 5 Flooring Installation Instructions 6 Flooring Installation Images 8 Wall Installation Instructions 9 Wall Installation Images 11 Maintenance Instructions 12 Product Warranty 13
weekendwarrior | P&S LVT Technical Data Sheet General Specifications Overall Product Thickness: Wear Layer Thickness: Product Type: Product Dimensions - Tile: Finish: Residential Warranty: Carton Quantity - 4" x 36": Carton Quantity - 6" x 36: Carton Quantity - 7" x 48": Carton Weight - 4" x 36": Carton Weight - 6" x 36": Carton Weight - 7" x 48": 1.5 mm 3 mils (0.07 mm) Peel & Stick Luxury Vinyl Tile (LVT) 4" x 36", 6" x 36", 7" x 48" Scratch-Resistant Polyurethane 15 years 20 Pieces (20 sq. ft.
weekendwarrior | P&S LVT General Information Limitations WeekendWarrior is a peel-and-stick vinyl product that is designed to be installed in residential indoor applications only. This product must be installed over an approved substrate that is properly primed with a suitable latex-based primer - failure to do so could result in adhesion issues. Avoid prolonged exposure to direct sunlight or other heat sources where temperatures will exceed 90° F (32° C), as damage or deformation may occur.
weekendwarrior | P&S LVT Recommended Tool List • Knee Pads • Safety Glasses • Cut-Resistant Safety Gloves • Dust Mask • HEPA-Filtered Vacuum • Paint Roller & Floor/Wall Primer • Three-Section Wall Roller with Extendable Handle (~9 in. Wide) or Three-Section 100 lb. Floor Roller • Pencil • Speed Square • Tape Measure • Utility Knife with Blades • 6-foot and 1-foot Straight Edge or Level DuraDecor | P: (855) 700 - 5666 | customercare@duradecor.com | duradecor.com | revised on 06.23.
weekendwarrior | P&S LVT Flooring Installation Instructions 1. Floor Substrate Preparation Radiant Heating Substrates When installing floor covering over a substrate that contains a radiant heating system, ensure the radiant heat does not directly contact the floor covering and is set at the correct “in-service” temperature for 48-hours prior, during and after the installation. The radiant heat may be gradually increased or decreased to maintain the correct “in-service” site conditions.
weekendwarrior | P&S LVT Floor Installation Instructions use a pen or permanent marker. It is recommended that plank end joints be staggered randomly by at least 8 in. to avoid an undesirable “stair stepped” or “H joint” pattern (see figure 2). Tiles are recommended to be installed either in a brick-bond or a 1/3rd off-set pattern. and your body weight or a 100 lb. three-section roller (see figure 6). Failure to roll correctly may result in bond failure.
weekendwarrior | P&S LVT Flooring Installation Images Figure 1: Layout - Mark the starting line Figure 4: Cutting - Mark, score & snap downward Figure 2: Layout - Stagger seams Figure 5: Installation - Remove release paper Figure 3: Priming & Cleaning - Prime substrate Figure 6: Installation - Roll flooring with roller DuraDecor | P: (855) 700 - 5666 | customercare@duradecor.com | duradecor.com | revised on 06.23.
weekendwarrior | P&S LVT Wall Installation Instructions 1. Wall Substrate Preparation 2. Wall Installation Instructions Flatness Acclimation Drywall Substrates Layout Check all substrates for flatness - all areas should be smooth and flat. The recommended flatness tolerance is < 1/8-in. gap (2 x U.S. quarters) underneath a 6-ft. straight level and < 1/16-in. gap (1 x U.S. quarter) under a 1-ft. level. Make any necessary and appropriate adjustments to the substrate before installation.
weekendwarrior | P&S LVT Wall Installation Instructions visible defects or damage, as removal, subfloor repair and replacement labor costs will not be covered. Remove the release paper on the bottom of the tile and discard immediately in a trash can or bag (see figure 4). Follow the layout and starting line and carefully position each piece accordingly, keeping all joints snug without compressing the material (see figure 5).
weekendwarrior | P&S LVT Wall Installation Images Figure 1: Layout - Mark the starting line Figure 4: Installation - Remove release paper Figure 2: Layout - Stagger seams Figure 5: Installation - Install along starting line Figure : Cutting - Mark, score & snap downward Figure 6: Installation - Roll flooring with roller DuraDecor | P: (855) 700 - 5666 | customercare@duradecor.com | duradecor.com | revised on 06.23.
weekendwarrior | P&S LVT Maintenance Instructions 1. Precautions Do not perform any maintenance procedures on wall installations for 72-hours. Remove all metal objects before conducting maintenance and prohibit foot traffic until the floor is dry. Do not use dust mops treated with oils or silicones, acetone, strong alkaline cleaning agents, multisurface cleaners, vinegar/ammonia/ citrus oil solutions, scouring powder, strong solvents, or abrasive cleaning pads, as these can damage the flooring.
weekendwarrior | P&S LVT Product Warranty 1. General Terms 2. Warranty Terms & Provisions Novalis Innovative Flooring (“Manufacturer”) warrants that, when used properly and under normal operating conditions, the products described in the Manufacturer’s catalog as WeekendWarrior Peel and Stick Luxury Vinyl Wall and Floor Tile (“Product”), a 1.5mm glue down vinyl tile. The Product is a Luxury Vinyl floor covering (LVT/LVP) that is pre-coated with a hot-melt adhesive.
weekendwarrior | P&S LVT 2.6. Petproof Warranty: The Product surface coating provides scratch and stain resistance (such as feces, urine and/ or vomit) from domestic household pets, such as cats and dogs, provided that pet claws are routinely cut and filed. 3.
weekendwarrior | P&S LVT 5. Warranty Claims If, within the applicable warranty period identified in Article 2.1 and 2.2, the Customer discovers any problems or defects in the Product that may be covered by this Limited Warranty, the Customer must notify the distributor or the Manufacturer directly at 1-(855) 700 - 5666 or customercare@duradecor.com.
