Installation Guide

ManualsBrandsDuraflame ManualsElectric Stoves1,000 sq. ft. Infrared Electric Fireplace Stove with Remote Control

MODELS: DFI-8511-01, DFI-8511-02, DFI-8511-03, DFI-8511-04,DFI-8511-05,DFI-8511-06

- POWER

Made in China

Printed in China

3. Pinch this spring clip to

loosen. Gently turn and pull the

rubber grommet of the motor

shaft.

REPLACING THE LIGHT BULB

VOLTAGE 120 VAC, 60 Hz

AMPS 12.5 Amps

WATTS 1500 Watts

OPERATING INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

PRODUCT SPECIFICATIONS

•Use the power button to turn on or off the stove

from the remote or control panel.

•Use the + and - buttons to adjust the ame

brightness.

- FLAME

For Customer Service:

www.twinstarhome.com

888-674-7517

8:30 a.m.-5:30 p.m., EST, Monday-Friday

Pull

Light bulb retaining spring

1. Loosen Phillips head screws

and remove back panel.

2. Remove back panel to access

light bulb

Distributed by

Twin-Star International, Inc. Under license.

duraflame™ and the duraflame flame

logo are trademarks of Duraflame, Inc.

Twin-Star International, Inc.

Delray Beach, FL 33445

Made in China • Printed in China

MOUNTING THE LEGS

1. Align the 2 mounting tabs into the bracket (Fig 1)

2. Slide the legs outward to lock in place. The legs will snap into place

when correctly installed. (Fig 2)

3. Fasten the legs to the base using the included screws,1 per leg. If the

screw hole does not line up check that the legs are properly snapped

into place. (Fig 3)

Note: When rst running the heater there can

be an odor. This is normal, the heater has a

surface coating on the internal parts, for the

rst several hours of operation the coating

reacts with the internal parts to permanently

protect them. The odor is safe; if you are

sensitive to the odor it is recommended

to run the heater in a well-ventilated area

until the odor dissipates.

Warning: This is an unvented, electric appliance.

DO NOT attempt to burn wood or manufactured

relogs in or on this appliance or grate.

Leg

Bracket

4. Pull away the bulb retaining

spring, unscrew the old bulb,

and replace with a new 40w

candelabra bulb.

Spinner

Motor

Assembly

Light bulb

-HEATER

•Press the HEATER button to cycle through 1000W,

1500W and OFF.

•The heater will beep once when set to 1000W,

twice for 1500W, and three times for OFF.

Go to www.tsicustomerservice.com for product warranty registration

Summary of content (2 pages)

PAGE 1
MODELS: DFI-8511-01, DFI-8511-02, DFI-8511-03, DFI-8511-04,DFI-8511-05,DFI-8511-06 Go to www.tsicustomerservice.com for product warranty registration ASSEMBLY INSTRUCTIONS 1 2 OPERATING INSTRUCTIONS - POWER 3 •Use the power button to turn on or off the stove from the remote or control panel. - FLAME Leg •Use the + and - buttons to adjust the flame brightness. -HEATER Bracket MOUNTING THE LEGS 1. Align the 2 mounting tabs into the bracket (Fig 1) 2. Slide the legs outward to lock in place.
PAGE 2
WARNING: In order to avoid overheating, do not cover the heater. IMPORTANT INSTRUCTIONS 3. CAUTION: Whenever the heater is left operating and unattended, extreme caution is necessary if chi 4.