Instructions / Assembly

ManualsBrandsDuraHeat ManualsHeater AccessoriesReplacement Wick for Select Envirotemp HeatMate KeroHeat KeroJet and Sengoku Kerosene Heaters

WICK ASSEMBLY- Check at least once a month!!

The burner assembly sits on top of the wick guide. Over time, tar deposits can

accumulate on the wick guide, and this can prevent the burner assembly from

seating properly. This can result in poor combustion, smoke, odor, etc.. To prevent

this from happening, tar deposits on the wick guide can be removed as follows:

Making sure that the heater is both cool and turned off, lower the wick to the "off" position.

Remove the batteries (located at the rear of the heater).

Remove the 2 cabinet screws. Lift off the cabinet and grill assembly as shown in

illustration. (Fig.A)

Using the wick adjuster knob, raise the top of the wick until it is even with the top

of the wick guide. Using a flat-edge screwdriver, scrape off the tar deposits.

Be careful not to allow any of the tar deposits to drop into the grooves of the wick

guide. A small vacuum cleaner can be used to remove the tar deposits that have

been scraped off. (Fig.B)

Reassemble the heater and replace the batteries.

WICK REPLACEMENT

The wick in your heater needs replacing if, after repeated cleanings, any of the following conditions still exist: slow to light,

hard movement of the wick adjuster knob, kerosene odor while burning, low heat output, slow warm up, damaged wick.

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

4. Gently pull the wick adjustment

knob off the heater.

5. Remove the cabinet base by

lifting it from the back and

tilting it forward to clear the

wick adjuster assembly.

6. Trip the pendulum on the

automatic safety shutoff

system to lower the wick.

Fig.A

Fig.B

1. Push down the manual shut-off knob and turn the wick adjustment knob COUNTERCLOCKWISE

in the direction of "OFF".

2. Use a screwdriver to loosen and remove

cabinet screws on either side of the heater

cabinet.

3. Use the carrying handle to lift the cabinet

straight up and away from the heater.

Use only a genuine replacement wick.

REPLACEMENT WICK NUMBER: Kero-World 32225, Dura Heat DH-145, Pick-A-Wick PW-72.

If cleaning the Wick does not improve performance, you will need to replace the wick. Refer to the "TROUBLE

SHOOTING GUIDE", see page 14, which outlines conditions under which the wick should be replaced.

CAUTION :

Use ONLY a genuine Replacement

Wick. Part Number :

Kero - World 32225, Dura Heat DH-145,

Pick-A-Wick PW-72. DO NOT attempt to substitute any other type of wick device or a wick designed for another

brand or model heater. You could damage the heater and create a potential fire hazard.

Call customer service at 814-643-1775, to order a wick.

Visit our website at www.yourheater.com for a link to detailed wick replacing directions.

ATTENTION : The only tools needed to replace the Wick are :

A pair of pliers A flat blade screwdriver A plastic bag with a twist tie

http://worldmkting.com/wick-installation-instructions

Summary of content (3 pages)

PAGE 1
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! http://worldmkting.com/wick-installation-instructions WICK ASSEMBLY- Check at least once a month!! The burner assembly sits on top of the wick guide. Over time, tar deposits can accumulate on the wick guide, and this can prevent the burner assembly from seating properly. This can result in poor combustion, smoke, odor, etc..
PAGE 2
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! 7. Remove the four wing nuts which hold the wick assembly to the heater and carefully lift the wick assembly from the heater. 8. Replace the wick adjustment knob temporarily. Turn the knob CLOCKWISE to raise the wick. 9. Hold the wick assembly up-side- down, using caution, grasp the wick cover firmly PULL it off with a sharp tug. If you have difficulty doing so, try loosening the wick cover with a flat blade screwdriver.
PAGE 3
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! 15.Turn the wick assembly upside down to replace the wick cover. 16. Align the tabs on the wick cover with the four screw holes on the bottom of the assembly, as shown, and snap it into place. Be certain of firm contact at all points. 17. Be sure the rubber seal on tank is properly seated. Fig.A Fig.B Fig.C 18. (1) Turn the wick adjustment knob to the fully raised position. (2) Pull lightly on the skirt of the wick to remove any slack.