TM A Product of A L L P U R P O S E V I N Y L USP US POLYMERS INC G A R A G E S Vinyl Garage Patent #416.091 OWNER’S MANUAL / Instructions for Assembly Size 10 Ft x 15 Ft (Approx.) with “Extension Kits” Ver: 2.0 Customer Service Hotline (800) 483-4674 www.uspolymersinc.com Your Total Solution To maintenance Free Garages. Requires two people and takes about 4-5 hours for Installation.
Duramax Garages Limited Ten Year Warranty U.S. Polymer Inc. will send a replacement part free of charge, in the event of material defects and or workmanship for a period of ten years from the date of purchase. This warranty is extended only to the original purchaser. A purchase receipt or other proof of date of original purchase will be required before warranty service is rendered. In no event shall we pay the cost of flooring, labor, installation or any other costs related thereto.
Parts List Note: Check all parts prior to installation.
One Extension Parts List Note: Check all parts prior to installation.
Exploded View RRS RRS RRS RRS RRS RP RRS RP RP RP RP RP RP RP RP RP RP RP RS3LA MJ RS3LA FPR RS2A RS1H RS4XA RS4XA MJ RS2A RS6H RS4XA RS4XA RS1H RS15R RS15L RS3LH RS2A RS1H FPL RS5A RS7H RS3LA RS4XA RS16L MJ RS15R SP DS FPL RS16R RS4XA RS3LA RS1H RS2A SP SP MJ SP SP SP FPR SP SP RS3LA SP CMA CMA CMA CMH CMA CMA CB3XA CCA CDLH CB3XA CDRH CB6H MJ MJ EXTL CB1A CCA CB4A CB1H B3RA B1RA B1LH CB4H CB3XA CCA CDRA FSPH CMH CB3XA MJ CMA B22 CB4H CMA
Exploded View with One Extension RRS RP RP RS6H RS3H RS4XA RS7H RS3H MJ SP CMH CB2A MJ EXTL MJ CB2A EXTR CMH SP F07 FO6A F07
Roof Structure Exploded View RS10A RS2A RS2A RS1H RS9H RS8H RS3LA RS4XA 11 A RS1H RS RS12A RS4XA RS RS RS 6H 7H RS 7H RS2A MJ 6H RS4XA RS15R RS 11 A RS3LA RS4XA R MJ RS RS19H 6H 11 RS 6H RS RS 7H RS3LA 7H MJ A RS4XA 11 RS15R RS RS4XA RS 6H RS 7H RS RS19H RS20H RS4XA 6H RS3LA 11 RS12A RS DSHH RS5A RS5A RS4XA RS5A R 7H A RS RS15L A S5 RS3LH RS2A RS16R RS10A RS9H RS16L RS8H RS2A RS8H RS9H RS1H RS20H RS12A 6H RS3LA MJ 7H RS4XA RS RS4XA R
Roof Structure Exploded View With One Extension RS3H RS7H RS7H RS6H RS4XA RS6H RS3H RS15R RS11A RS4XA RS20H RS19H MJ RS15L MJ
A. Foundation PART 1 : Assembling Shed With Extension Kit Note: It is important that these instructions are followed step by step. Note All parts are clearly marked and care should be taken to use the correct one.
2. Assemble the channel (F04A), (F05A) & (F07) together using (S1) screws. Make 6 sets. Add one (F07) for each Extension. F07 F07 F07 F07 F05A S1 F04A 3. S1 Make a frame with the sub assemblies as shown below. Note Make sure while assembling, the channel position should be as shown.
4. Fix the ‘L’ angle (F03) to the channel at all the four corners to make a perfect frame. See fig. S1 F03 5. Fix the channel (F04A), (F05A) & (F07) sub assembly into the main frame as shown. See fig. F07 F07 Note Make sure while assembling, the channel position should be as shown. F07 F07 F07 F05A S1 F04A F07 F07 F07 F05A F04A F07 F07 F07 F07 F07 F07 F05A F07 F07 F07 F05A F04A F04A Channel Position Front S1 6. Fix the channel (F06A) into the frame with (S1) screws as shown.
7. Place the channel (F03H) into the frame equaly spaced as shown. Use (F08) plate to connect the ‘U’ channel and the frame with (S1) screws. Add two (F03H) for each Extension. S1 S1 F08 F08 F03H F03H 8. Assemble the Base U-Channel on top of the foundation with (S1) screws as shown in fig. Add one (EXTL) & (EXTR) for each Extension.
9. Place the ramp (RG) to the front side of the foundation and keep the distance according to the wheel distance. Use dia. 2.5mm. drill bit to transfer the hole from (RG) and fix with (S1) screws. S1 RG Gravel RG Filler Material and Flooring Recommendation OPTION - 1. Gravel Floor with Plywood a. After completing the assembly of the base Uchannel fill the gravel up to the foundation top surface only. Fill the concrete inside the ramp only. Ramp m. Concrete b.
c. Secure the plywood to the foundation with screws. (Screws not included.) Concrete OPTION - 2. Cement Floor with out Plywood. After completing the assembly of the base U-channel fill the concrete up to the foundation top surface only. Ramp Concrete B.
1. Slide the door column (CDRA) into the base U-channel (B1RH) on the right side of the door. Line up the pre drilled holes on column (CDRA) with base ‘U’ channel. Secure with two (S1) screws from inside. See fig. 1 CDRA CDRA B1RH CDRA Fig.1 2&3 Fig.2 B1RH CDRA Fro nt B1RH S1 Fig.3 2. Insert the front side panel (FSPH ) into the groove of column (CDRA). Start at the bottom of the panel at an angle then push into place.
3. Slide the corner column (CCA) into side panel (FSPH ) pushing the column to the side panel. 1 CCA FSPH B22 B1RH CCA CCA FSPH Fig.1 Fig.2 CCA FSPH S1 Fig.3 2&3 4. Fix the center band fitting (FCB) to the column (CCA) with (S2) screw. Leave it loose.
5. Fix the center band (CB1H) to the center band fitting (FCB) with (S1) screws. See fig.1. Fix the other end to the door column (CDRA). See fig.2. 1 S1 CDRA 2 CB1H CDRA CB1H FCB CB1H S1 Fig.1 Fig.2 6. Fix the center band (CB4H) to the base ‘U’ channel (B1RH) and door column (CDRA) with (S1) screws. See fig.1&2. Fix the (EPS) at the end of (CB1H) & (CB4H). See fig.3. 2&3 CB4H CDRA B1RH CB4H Fig.1 CB4H Fig.2 CB1H EPS 1 CB4H 9 Fig.
7. Working from inside continue connecting the 7 side panels (SP ) and columns to the base ‘U’ channel. Use (S1) screws to fix column to base. Add one side panel (SP ) & column (CMH) for each Extension. SP Note Window can be fixed any place except front panel. SP SP SP CMA SP CMH SP CMA SP CMH CMA CMH S1 8. Slide the corner column (CCA) into side panel (SP ) pushing the column to the side panel. Working from outside use (S1) screws to secure column to base (EXTR) & (B3RA).
9. Fix the center band fitting (FCB) to the column (CCA) with (S2) screw. Leave it loose. CCA FCB S2 Back 10. Assemble the center bands (CB3XA) with middle joining support (MJ) with (S1) Screws. See fig.1. Assemble (CB3XA) & (CB3A) together with (S3) bolt & nut. See fig. 2. Assemble (CB3A) & (CB2A) together with (S1) screws. See fig. 3. Add one (CB2A) for each Extension. S1 CB3XA CB3A S1 CB3XA 1 CB3XA CB3XA MJ S3 Fig.2 Fig.1 2 CB3XA 3 S1 CB3A CB3A S3 CB2A CB2A 11 MJ Fig.
11. Stabilize the side panels with center bands (CB3XA) & (CB3A) assembly. See fig.1 to 6 and follow the steps. S1 CMA FCB CMH CMA CMH CB3XA Fig.2 Fig.1 3&6 CB3XA CB3XA 2 3&6 S1 2 2 2 CMA CMH S1 1&5 CB3A 4 CMH CB2A CB2A FCB S1 Fig.4 Fig.3 CMH CBC CB3XA CB1H SP S1 Fig.6 Fig.5 SP 12. Working from inside continue connecting the 3 side panels (SP ) and columns to the base ‘U’ channel. Use (S1) screws to fix column to base.
13. Slide the corner column (CCA) into side panel (SP ) pushing the column to the side panel. Working from outside use (S1) screws to secure column to base (B3LA) & (EXTL). 1 CCA B3LA CCA SP SP EXTL CCA Fig.1 Fig.2 CCA B3LA EXTL S1 2&3 Fig.3 14. Fix the center band fitting (FCB) to the column (CCA) with (S2) screw. Leave it loose.
15. Assemble the center bands (CB3XA) with middle joining support (MJ) with (S1) screws. See fig. S1 CB3XA S1 CB3XA CB3XA MJ CB3XA 16. Stabilize the side panels with center bands (CB3XA) assembly. See fig.1 to 6 and follow the steps. FCB S1 CMA CB3XA CB3XA S1 Fig.2 Fig.1 CMA CMA 2 CB3XA CB3XA CMA FCB 2 CB3XA S1 3&6 CB3XA 4 Fig.4 Fig.3 CB3XA CMA ide ns kI c Ba CBC CB3XA 14 S1 CB2A Fig.5 CB3XA Fig.
17. Working from inside continue connecting the side panels (SP ) and columns to the base ‘U’ channel. Use (S1) screws to fix column to base. SP SP SP SP CMH CMA SP CMH CMA EXTL EXTL EXTL S1 EXTL B1LA 18. Slide the door column (CDLH) into the base ‘U’ Channel & side panel. Line up the pre drilled holes on (CDLH) & base ‘U’ channel (B1LA) & fix with (S1) screws from inside. 1 CDLH SP B1LA SP CDLH CDLH S1 Fig.1 Fig.
19. Assemble the center bands (CB3XA), (CB6H) & (CB2A) togther with middle joining support (MJ) with (S1) Screws. See fig. Add one (CB2A) for each Extension. 2 CB2A 1 S1 CB3XA S1 S1 CB2A CB3XA CB6H CB3XA CB6H MJ MJ Fig.1 20. Stabilize the side panels with center bands (CB3XA), (CB6H) & (CB2A) assembly. See fig.1 to 5 and follow the steps. Fig.2 FCB S1 CMA CB3XA CB3XA CB2A S1 CMH Fig.2 Fig.1 CMA CMH CDLH CB6H CMH CMA CDLH S1 S1 Fig.4 Fig.3 2 4 CB6H CB2A S1 16 CB3XA Fig.
21. Fix the (EPS) at the end of center band (CB6H). See fig.1. Fix the (CBC) to the center band joint position to avoide injury. See fig.2. CDLH 2 CMA CB6H CB2A 2 CBC CDLH CB3XA EPS Fig.1 Fig.2 1 CB6H 22. Slide the door column (CDRH) into the base ‘U’ Channel. Line up the pre drilled holes on (CDRH) & base ‘U’ channel (B1RA) & fix with (S1) screws from inside. 1 CDRH CDRH CDRH B1RA Fig.2 Fig.1 CDRH 2&3 B1RA B1RA S1 17 Fig.
23. Insert the side panel (SP ) into the groove of column (CDRH) & base ‘U’ channel (B1RA). CDRH SP B1RA 24. Slide the corner column (CCA) into side panel (SP ) pushing the column to the side panel. Working from outside use (S1) screws to secure column to base (B1RA) & (B1LH). 1 CCA B1RA SP SP CCA B1LH CCA Fig.1 Fig.2 CCA 2&3 B1LH S1 18 Fig.
25. Fix the center band fitting (FCB) to the column (CCA) with (S2) screw. Leave it loose. CCA CCA FCB S2 26. Fix the center band (CB1A) to the center band fitting (FCB) with (S1) screws. See fig.1. Fix the other end to the door column (CDRH). See fig.2. S1 CDRH 1 CDRH CB1A FCB B1RA CB1A S1 Fig.1 19 2 CB1A Fig.
27. Fix the center band (CB4A) to the base ‘U’ channel (B1RA) and door column (CDRH) with (S1) screws. See fig.1&2. Fix the (EPS) at the end of (CB1A) & (CB4A). See fig.3. CB4A CDRH CB1A S1 S1 2&3 CDRH B1RA CB4A Fig.2 Fig.1 CB4A CB1A EPS 1 CB4A B1RA Fig.3 28. Insert the side panel (FSPH ) into the groove of column (CCA) & base ‘U’ channel (B1LH).
. Slide the door column (CDLA) into the base ‘U’ Channel & side panel. Line up the pre drilled holes on (CDLA) & base ‘U’ channel (B1LH) & fix with (S1) screws from inside. 1 FSPH FSPH CDLA CDLA B1LH CDLA S1 Fig.2 Fig.1 2 B1LH 30. Fix the center band (CB1H) to the center band fitting (FCB) with (S1) screws. See fig.1. Fix the other end to the door column (CDLA). See fig.2. FCB S1 CDLA CB1H CDLA 1&3 CB1H 2 Fig.1 Fig.2 CB1H CB1H S1 Note 21 CB1A Fig.
31. Fix the center band (CB4H) to the base ‘U’ channel (B1LH) and door column (CDLA) with (S1) screws. See fig.1&2. Fix the (EPS) at the end of (CB1H) & (CB4H). See fig.3. CB4H CDLA 2&3 B1LH CDLA S1 CB4H Fig.2 Fig.1 S1 CB4H CB1H EPS B1LH CB4H Fig.
C.
2. Insert the corner column fittings (FCC) into the corner column (CCA). Fix with (S1) screws from outside of the shed. FCC FCC CCA CCA FCC 3. Insert the door column fittings (FDCLC) & (FDCRH) into the front door column (CDLA) & (CDRA). See fig.1&2. Insert the door column fittings (FDCL) & (FDCR) into the side door column (CDLH) & (CDRH). Fix the fitting (FDCR) to the column (CDRH) by (S1) screw. All other fittings will be screwed later. See fig.3&4.
Front roof structure assembly 4. Assemble front roof structures (RS1H) 2 nos. with middle joining support (MJ). Use (S1) screws. MJ RS1H RS1H RS1H S1 S1 RS1H 5. Assemble roof structure support (RS8H) & (RS9H) to (RS1H) assembly with 4 (S1) screws as shown in fig. Note Make sure the hole position and direction of the ‘U’ channel.
6. Assemble the roof structure (RS2A) to (RS8H) & (RS9H) with 8 (S1) screws. S1 RS2A RS2A RS9H RS8H RS2A RS8H RS9H 7. Assemble door stopper (RS16L) & (RS16R) together with (S8) bolt & nut with washers.
8. Assemble (RS16R) & (RS16L) assembly to front roof assembly with (S1) screws. RS16L RS16R S1 Back roof structure assembly 9. Assemble front roof structures (RS1H) 2 nos. with middle joining support (MJ). Use (S1) screws.
10. Assemble roof structure support (RS8H) & (RS9H) to (RS1H) assembly with 8 (S1) screws as shown in fig. Make sure these holes up U h -C an n O el p in en U- a Ch nn el e Op nin g RS8H g RS1H RS8H RS9H S1 RS1H 11. Assemble the roof structure (RS2A) to (RS8H) & (RS9H) with 8 (S1) screws.
12. Assemble roof structure (RS3LA) & (RS3LH) with middle joining support (MJ). Use (S1) screws to fix. Add one (RS3H) for each Extension. RS3H S1 RS3LA RS3LA RS3LA MJ RS3LA RS3LA 13. Insert 90 degree joint (RJ) into the roof structure (RS3LA) & (RS3H) assembly . Use (S1) screw to fix. Repeat on other end of (RS3H).
14. Assemble roof structure (RS3LH), (RS3LA) & (RS3H) with middle joining support (MJ). Use (S1) screws to fix. Add one (RS3H) for each Extension. RS3H S1 RS3LA RS3LA RS3LH MJ RS3LA RS3LH 15. Insert 90 degree joint (RJ) into the roof structure S1 (RS3LH). Use (S1) screw to fix. Repeat on other end of (RS3H).
16. Assemble the roof structure (RS5A) & (RS6H) with (S1) screws. Add one (RS6H) for each Extension. Make 2 sets. Do not fix any screws on this two holes. Do not fix any screws on this two holes. RS6H RS6H RS6H RS5A RS6H RS6H 17. Assemble the roof structure (RS13A) into (RS5A) & (RS6H) assembly with (S3) bolt & nuts.
18. Assemble the roof structure (RS5A) & (RS7H) with (S1) screws. Add one (RS7H) for each Extension. Make 2 sets. RS7H RS7H Do not fix any screws on this two holes. RS7H RS7H Do not fix any screws on this two holes. RS7H S1 Do not fix any screws on this two holes. RS5A 19. Assemble the roof structure (RS13A) into (RS5A) & (RS7H) assembly with (S3) bolt & nuts.
20. Place the assembled front roof structure assembly to the door columns. Line up the pre drilled holes with door column and fix with (S1) screws. See fig.1&2. Make sure the (RS2A) structure position as shown in fig.3. 2 3 RS16L RS16R RS16R 1 Fr RS16L CDRA Fig.1 on s t In ide CDLA S1 Fig.2 S1 RS2A Fig.3 21. Place the assembled back roof structure at the back wall, on top of middle columns (CMA). Line up pre drilled holes with middle column fittings (FMC).
22. Insert the 90 degree joint (RJ) (assembled with (RS3) roof structure) into the roof structure (RS1H). See fig.1. Secure (RJ) to (RS1H) with (S1) screw. See fig.2. Secure (RJ) with (FCC) using (S2) screw. See fig.3 Fix (RS2A) to (RJ) through (RS3) assembly with (S1) screw. See fig.4. Repeat the same for other 3 corners. RS3H RS3LA RS3LA RS3LH RS3LH RS3LA RS3H RS1H RS3LA RS1H RS3LA RJ S1 RJ Fig.2 Fig.1 S1 S2 RS2A RS3 RJ FCC Fig.4 Fig.3 23.
24. Fix the door stopper (DSHH) to the roof structure (RS3LH) with (S1) screws. RS3LH RS3LH DSHH CDLH DSHH CDRH S1 CDRH 25. Place the assembled roof structure (RS5A) & (RS6H) into position on roof structure supports (RS8H) at the left side of the shed. Use (S1) screws to fix. Repeat the same for assembling (RS5A) & (RS7H) assembly. See fig.1&2. RS6H RS5A S1 RS6H RS5A RS8H S1 RS8H Fig.1 35 2 RS7H RS7H Fig.
26. Place the assembled roof structure (RS5A) & (RS6H) into position on roof structure supports (RS9H) at the left side of the shed. Use (S1) screws to fix. See fig.1&2. Repeat the same for assembling (RS5A) & (RS7H) assembly. 2 RS6H RS7H 1 RS5A RS9H S1 RS5A RS5A RS6H S1 RS9H Fig.2 Fig.1 27. Fix the vertical support (RS19H) & (RS20H) to (RS5) assembly with (S1) screws. Add two (RS19H) & (RS20H) for each Extension.
28. Attach the roof structure (RS4XA) 12 nos. to (RS3LH) & (RS3LA) assembly with (S1) screws. See fig.1. Attach the roof structure (RS4XA) to (RS5A), (RS6H) assembly and (RS5A), (RS7H) assembly with (S7) screws. See fig.2&3. Add two (RS4XA) for each Extension. RS4XA RS4XA RS4XA S1 RS4XA RS4XA RS4XA RS4XA RS4XA RS4XA 3 RS4XA RS4XA 2 RS4XA RS4XA 1 RS4XA RS3LA Fig.1 Fig.2 S7 RS6H RS4XA RS7H RS4XA RS5A RS5A Fig.3 29.
30. Attach the roof structure support (RS12A) with (RS5A) to (RS5A) and (RS6H) to (RS7H) with (S1) screws. RS12A RS12A RS5A RS12A RS12A S1 31. Assemble the roof structure support (RS15L) & (RS15R) together with (S8) bolt & nut with washers. Make three sets.
32. Fix the assembled roof structure support (RS15L) & (RS15R) to the column (CMH) & (CDLH) with (S1) & (S2) screws. See fig. Add one (RS15L) & (RS15R) for each Extension. 2 RS15L 2 RS15L 1 RS15L RS15R RS15R RS15L S2 CMH RS15L S2 S2 CDLH Fig.1 RS15R S2 CMH S1 CMH CDLH S1 CMH Fig.2 33. Attach the roof structure support (RS15L) & (RS15R) assembly to (RS19H) & (RS20H) with (S1) screws. See fig.1&2. Fix the cover (TCH) at the bottom of (RS19H) & (RS20H) with (S1) screws. See fig.3.
D. Roof panels Parts Needed: (12) Roof Panels (2) Facia Panel Left (2) Facia Panel Right (6) Ridge Cover Small (128) Roof Plug with Washer (128) Roof Pin (24) Sagging Support (RP ) (FPL) (FPR) (RRS) (PPG) (PIN) (RS14A) Parts Needed For each Extension: (2) (1) (58) (58) (4) Roof Panels Ridge Cover Small Roof Plug with Washer Roof Pin Sagging Support FPR (RP ) (RRS) (PPG) (PIN) (RS14A) 1. Place facia panel (FPR) to front roof structure right side.
3. Place facia panel (FPR) to back roof structure right side. Repeat the same step 1. FPR Back 4. Place facia panel (FPL) to back roof structure left side. Repeat the same step 1.
5. Start attaching the roof panels from (FPL) corner side by sliding the roof panel (RP ) to roof structure. Locate the hole positions of the roof panel and roof structure. Fix roof plug with washers. Use a hammer to drive in roof pins. See fig. Note Note Use a screw driver to align the holes. Insert roof plugs into roof panels only as indicated. Roof Panel installation by using ladder from inside at missing Panels. PPG RP RP FPL Fig. 1 Front Fig. 2 RP RP RP RP RP 42 Fig.
6. Continue to attaching the roof panels from back right. After fixing each roof panel attach each ridge cover (RRS). See fig. and follow the steps. B ac k RRS RP Fig. 2 Fig. 1 RP Fig. 3 RRS Fig. 4 RP RRS Fig. 5 43 Fig.
RRS RP Fig. 8 Fig. 7 RRS RP Fig. 9 Fig. 10 RRS RP Fr o Fig. 11 44 nt Fig.
7. Insert the sagging support (RS14A) from inside the shed by sliding in between roof structure (RS5) and roof panel until it reaches (RS3) roof structure for each panel. See fig.1. 8. Insert the sagging support (RS14A) from inside the shed by sliding in between roof structure (RS5) and roof panel until it touches the other roof structure (RS5). See fig.2. RS14A RS5 RS14A RS3 Inside View Outside View Fig. 1 Fig. 2 E.
Note: To prevent water leakage it is important that these instructions are followed. 1. After completing the assembly apply silicone around the perimeter of the base U-channel. Seal the corners, joints and base of door column Base U-channel 2. After completing the panel assembly, apply silicone around the roof plugs. This is optional and should be done for heavy rain areas if needed.
F. Ventilation Kit ACCESSORIES CODE DESCRIPTION VC VCP VENTILATION COVER VENTILATION COVER PIN QTY 2 4 VENTILATION COVER (VC) VENTILATION COVER PIN (VCP) TOOLS YOU WILL NEED Power Drill Dia 5/32” (4.2mm) drill bit Dia 1/2” (12.5mm) drill bit VC Optional ventilation kits can be installed on any of the wall panels. However, we recomend mounting them on the top of the shed’s back wall. 1. Place the ventilation cover (VC) as shown in fig.1. Using a pencil, mark the two side hole locations. 2.
High wind area installation instructions Note: To ensure that your shed withstands high winds, you will need the following reinforcement. Parts needed: CODE DESCRIPTION S4 DIA. 4.2 x 16mm. (5/32” x 5/8”) SHEET METAL SCREW M6 x 40mm. (1/4” x 1 1/2”) Anchor bolt with nut S5 QTY 68 (not included with shed) 51 (not included with shed) 1. Shed or shed foundation should be placed on concrete footing by use of anchor bolt and nut. Using a carpenters square, line up corners.
3. Attach each side panel (SP ) on top to the roof structure (RS1) and (RS3). Using a dia. 3mm (1/8”) drill with a power drill, make two equal distance holes on the side panel through the roof structure. Drive a self tapping screw (S4) through the side panel to the roof structure. Repeat this for every side panel. See blowup.
PART 2 : Adding Extension Kit to Existing Shed Back Front 1. Remove one ridge cover (RRS) from the back side . See the figure. Remove this Ridge cover. Back TIP 50 Use a drilling machine to remove the pins and plugs from the ridge cover, roof panel and facia panel. Care should be taken not to damage the panels. Extra pins, plugs and washers are available in the accessory box.
2. Remove from back side left and right roof panel (RP ). See the figure. Back RP RP 3. Remove from back side left and right Facia Panel (FPL) & (FPR). See the figure.
4. Support the roof structure (RS6H) & (RS7H) by using an appropriate support to avoid the roof structure from collapsing. Note Back Support not included. RS6H RS7H Support 5. Remove from back side (RS10A) Roof Structure Support.
6. Remove (RS6H) & (RS7H) from (RS8H). Back S1 RS6H RS7H RS8H 7. Remove (RS6H) & (RS7H) from (RS9H). See fig. 1. Remove (RS13A) from (RS6H) & (RS7H). See fig. 2 Back RS6H S1 RS9H Fig.1 S3 RS13A RS6H 53 Fig.
8. Detach roof structure (RS2A) from (RS3) from both corner. see fig.1. Detach 90-degree joint (RJ) from corner column fitting (FCC) from both corner. See fig.2. Detach (RS3XA) from 90 degree joint (RJ) from both corner. See fig.3. Back S1 S2 RS3XA RS2A RJ FCC Fig.1 Fig.2 RS3XA S1 RJ Fig.3 9. Detach the middle column fitting (FMC) from roof structure aseembly (RS1H).
10. Pull the back roof structure assembly. See fig. Back 11. Remove the roof structure support (RS12A) from (RS6H) & (RS7H). See fig.1. Remove (RS11A) from (RS6H) & (RS7H). See fig.2. Note After complete the extension assembly of (RS6H) & (RS7H), fix again (RS11A) & (RS12A) at the same position. RS11A 1 2 RS6H RS12A RS6H RS11A RS12A 1 RS7H S1 S1 Fig.1 55 Fig.
12. Detach (RS4XA) from (RS6H) & (RS7H) assembly. After complete the extension assembly of (RS6H) & (RS7H), fix again (RS4XA) at the same position. Note RS4XA RS6H 2 RS4XA 1 RS4XA RS6H 2 RS7H S7 S7 Fig.2 Fig.1 Back 13. Remove the center band assembly from the back wall of the shed. Follow the figures. FCB Back S1 S1 1 3 FCB CB3XA 4 Fig.1 3 Fig.2 2 CMA CBXA CB3XA CBXA S1 56 Fig.3 Fig.
14. Remove the Corner column (CCA), Middle column (CMA) & Side panels from back side of the shed. Back CCA CMA 1 2 Fig.1 Fig.2 2 2 1 15. Remove the Base ‘U’ channel (B3LA) & (B3RA) from the foundation.
16. Remove (F01H), (F02H) & (F03) assembly from back side. F03 F01H F03 Back F02H 17.
U.S. Polymers, Inc. 1057 S.