Operation Manual

ManualsBrandsDurkopp Adler ManualsMiscellaneous8967

Contents: Page:

Preface and General Safety Information

Part 1: Operating Instructions Cl. 8967

1. Product Description

1.1 Short Description and Proper Use . . . . . . . . . . . . . . . . . . . . . 5

1.2 Sub-Classes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.3 Technical Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2. Operating Elements and Their Function

2.1 Elements at the Sewing Head . . . . . . . . . . . . . . . . . . . . . . . . 6

2.2 Elements on the Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3. Operating the Sewing Machine

3.1 Threading the Needle Thread . . . . . . . . . . . . . . . . . . . . . . . . 11

3.2 Winding the Bobbin Thread . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.3 Changing the Bobbin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.4 Setting the Bobbin Thread Tension . . . . . . . . . . . . . . . . . . . . . 14

3.5 Setting the Thread Regulator . . . . . . . . . . . . . . . . . . . . . . . . 15

4. Operating the Frame

4.1 Folding Down the Table Top . . . . . . . . . . . . . . . . . . . . . . . . . 16

5. Maintenance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Contents:Page:

Home

Summary of content (15 pages)

PAGE 1
Contents: Page: Home Preface and General Safety Information Part 1: Operating Instructions Cl. 8967 1. 1.1 1.2 1.3 Product Description Short Description and Proper Use . . . . . . . . . . . . . . . . . . . . . Sub-Classes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Technical Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 5 5 2. 2.1 2.2 Operating Elements and Their Function Elements at the Sewing Head . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 2
PAGE 3
1. Product Description 1.1 Short Description and Proper Use The special sewing machine 8967 is a single needle-double lock stitch free-arm machine with lower transport without stroke and an upper transport with alternating pressure feet. The machine is designed and may only be used for sewing of textile material or leather. 1.2 Sub-Classes 8967-160180 8967-160182 1.3 Execution without thread trimmer, Pressure foot lift electropneumatic.
PAGE 4
2. Operating Elements and Their Function 2.1 Elements at the Sewing Head Element Function 1 Pressure foot screw - This screw is screwed in completely at the factory and the position may not be changed. 2 Thread regulator - Setting the correct thread quantity for different material thicknesses, sewing yarns and stitch lengths. 3 Control knob - Setting auxiliary tension for the needle thread. 4 Lever - Opening the main needle thread tension and auxiliary needle thread tension.
PAGE 5
1 16 2 15 3 4 14 5 6 7 13 12 8 11 9 10 7
PAGE 6
2.2 Elements on the Frame Element Function Frame Type MG 55-3 1 Main switch 2 Pedal 3 - Switching the machine on and off Rest position - No function Position forward - Sewing with desired rpm Position "half back" - Raise pressure foot when machine at rest Position "full back" - Thread trimming and raise pressure foot Screw - Setting the Table Top Height.
PAGE 7
MG 55-3 3 2 1 MG 56-2 7 6 5 4 9
PAGE 8
Maintenance Unit 8 Air filter and water trap - Before the water level reaches the filter, screw in screw 7 far enough to drain water. Do not interrupt the compressed air supply. 9 Pressure regulator - To set to 6 bar pull the bushing 10 up and turn appropriately.
PAGE 9
3. Operating the Sewing Machine 3.1 Threading the Needle Thread. Caution Risk of Injury ! Turn off the main switch before threading. – Thread the needle thread as shown in the illustration.
PAGE 10
3.2 Winding the Bobbin Thread 1 2 3 4 5 6 – – – Place the bobbin 4 on the bobbin winder 3. – – Press the bobbinr lever 5 into the bobbin. Pull the thread through the guide 1 and the tension 2. Wind the thread approx. 5 x clockwise around the bobbin core and tear off at the thread clamp 6. Sewing The bobbin winder lever stops the procedure when the bobbin is full.
PAGE 11
3.3 Changing the Bobbin 3 4 7 1 6 5 2 Caution Risk of Injury! Turn off the main switch before changing the bobbin. – – – – – Bring the needle into the highest position Pull the covering cap 1 from the free-arm. Remove the bobbin housing 2 with bobbin 3. Hereby raise the bobbin case flap 4 as far as possible. Remove the bobbin Insert a full bobbin in such a way that, when the thread is pulled off, it turns in the direction shown in the illustration.
PAGE 12
3.4 Setting the Bobbin Thread Tension 2 1 Caution Risk of Injury! Turn off main switch. – – – Bring the needle into the highest position – Carefully turn the regulating screw 1. To the right = Increase thread tension To the left = Decrease thread tension Pull the covering cap from the free-arm Remove the bobbin housing with bobbin. Hereby raise the bobbin case flap as far as possible. The initial setting for the tension spring 2 is: The bobbin housing must slowly lower through its own weight.
PAGE 13
3.5 Setting the Thread Regulator. 1 With the thread regulator the needle thread quantity necessary for stitch formation can be regulated. The setting is dependent on the stitch length, material thickness and the yarn characteristics. Only a precisely set thread regulator assures an optimal sewing result. The needle thread loop should glide over the hook without excess with little tension.
PAGE 14
4. Operating the Frame 4.1 Folding Down the Table Top (only Frame MG 56-2) 3 1/ 2 4 Caution Risk of Injury! Hold the table top with both hands when pulling down. 16 – Release the table top fasteners 1 and 2 under the table top and fastener 3 on the left frame leg. – Pull down the table top with both hands as shown in the illustration. – – Lock the diagonal brace 4 into the mounting. Fold up the table top in the reverse order.
PAGE 15
5. Maintenance Caution Risk of Injury! Turn off main switch. Maintenance work must be conducted at the latest after the number of operating hours listed in the column " Interval". Shorter maintenance intervals may be required when working with very linty materials.