OWNERS MANUAL D16 Series This appliance is intended for commercial and household use. dustlesstools.com PATENT NO.
IMPORTANT SAFETY INSTRUCTIONS IMPORTANTES MESURES DE SECURITE IMPORTANTE PARA SU SEGURIDAD SAVE THESE INSTRUCTIONS CONSERVER CES INSTRUCTIONS GUARDAR ESTAS INSTRUCCIONES NOTE: The reading and understanding of the Owner’s Manual is imperative prior to operating this machine. If you or your operator(s) cannot read English, have this manual explained fully before attempting to operate this machine. Si Ud.
TOOL USE AND CARE TOOL USE AND CARE cont • Always check the filters before each use. Do not use without a dust collection bag and filters in place. • In the event of operational malfunction the vacuum must be shut down immediately. The malfunction must be rectified before starting the vacuum again. • Do not use with damaged cord or plug. • If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center.
IN THE BOX D1603 16 GAL WET+DRY DUSTLESSVAC WITH 12 FT.
IN THE BOX cont D1608 RENOVATE RIGHT EPA HEPA KIT: ChipBuddie HEPA Floor Tool DustBuddie + Adapter 18” Hose 16250 SHERWIN WILLIAMS HEPA RRP KIT: HEPA Floor Tool + Adapter 16500 DUSTLESS EPA LEAD SAFE COMPLIANCE: ChipBuddie Dustie 6’ Hose HEPA Floor Tool + #32 Clamp Adapter Zip Tie D1607 HEPA - 240V 16 GAL WET+DRY VAC: Filter Cover Extension Wands Floor Tool Crevice Tool Hose 10” Clamp Filter-Cleaning Weight Lid HEPA Filter Support HEPA Filter WunderBag Barrel Customer Service Helpline
SETUP 1. Remove entire contents of box. 2. Slide legs into slots with the legs with the hooks in the back. Screw in screws. 3. Attach tool tray. WUNDERBAG INSTALLATION 1. Place the cardboard collar with the rubber gasket securely over the intake port on the inside of the barrel. 2. Reach inside the port and with your fingers press cardboard tight and secure around port. 4. Place intermediate on barrel. Line Clamps up with the raised portion of the intermediate and secure in place. WET PICKUP 5.
USAGE DRY PICKUP CLEAN FILTERS (HEPA WET+DRY) 1. Barrel should be emptied of any wet waste. Filters must remain in place. 1. Turn the vacuum off and wait 5 seconds after motor comes to a stop. Repeat 5 times. This allows weight to expand filter cover and release dust. 2. Connect hose and desired attachment. 3. As suction is reduced stop to clean or replace filters. (Refer to Clean Filters or Filter Installation) 4. After use or when barrel is full turn off vacuum and disconnect from outlet. 5.
USAGE cont CHANGING WUNDERBAGS EXTENSION CORDS 1. Disconnect the vacuum from outlet. When using the appliance at a distance where an extension cord becomes necessary, a 3-conductor grounding cord of adequate size must be used for safety, and to prevent loss of power and overheating. Use the table that follows to determine A.W.G. wire size required. To determine ampere rating of your vacuum, refer to nameplate located on rear of motor cover.
MAINTENANCE FILTER INSTALLATION (REGULAR WET+DRY) FILTER INSTALLATION (HEPA WET+DRY) 1. Place the inner filter (small white filter) over the filter support cage and attach with the 7” hose clamp. Tighten the clamp with a screw driver. 1. Place the HEPA filter over the crosspiece stud and slide on the washer. Screw on the wing nut to compress the washer and filter seal. 2. Place the shaker basket rod in the brass hole. The basket should rest on top of the filter. 3.
MAINTENANCE cont FILTER INSTALLATION (HEPA WET+DRY) cont. 4. Place the filter-cleaning weight on the filter cover support, then place the HEPA filter cover over the HEPA filter cover support and HEPA filter. Place the 10” hose clamp over the HEPA filter cover so it rests on the metal ring of the filter. Tighten the clamp with a screw drive.
FAQ QUESTION ANSWER Why is the vacuum blowing dust? • Check filter(s) for holes and that they are securely in place. • WunderBag may not be securely in place. Why have I lost suction? • The drain cap may be open. • Check and clear any obstruction in the hose or attachments. • Filters may need to be cleaned/replaced. • Agitator rod cover/brass plug may need tightening. • WunderBag may be full and need to be replaced. • Hose may have a split and needs to be replaced.
OTHER PRODUCTS AVAILABLE (not to scale) 5” Dustie Model #D1854 1-3/8” BitBuddie DustBuddie for 7-1/4” Worm Drive & Hypoid Circular Saws Model #D4000 Model #D1900 5” DustBuddie Model #D1835 7” DustBuddie Model #D5850 HEPA Back Pack Model #15505 7” CutBuddie Model #D1750 Drywall Sander Model #50001 SawBuddie Model #D2415 12 OM007_0117 Customer Service Helpline 1.800.568.3949 dustlesstools.