User Manual

12
1) INPUT Connect your guitar to this input using a standard ¼” shielded instrument
cable.
2) GAIN (CLEAN) This knob sets the gain level of the clean channel.
3) LOW This knob controls the amount of low frequencies in your sound.
4) MID The Mid control regulates the midrange frequencies and it is an important part
of your tone shaping.
5) HIGH The High knob controls the amount of high frequencies in your sound.
6) LEVEL (CLEAN) This control is the master feed from the end of the clean channel
preamp channel to the power stage.
7) CLEAN/LEAD SWITCH This channel selector switches between the Clean and Lead channels. Channel-switching can also be controlled by a DUAL
footswitch that can be plugged on the amp’s front panel (14).
8) GAIN (LEAD) This knob sets the lead channel gain level, it determines the amount of drive or saturation for crunch or heavy distorted sounds and
also plays an important role in tone shaping.
9) LOW This knob controls the amount of low frequencies in your sound. When you’re starting to explore sounds on the amp, avoid boosting the lows
too much as this can reduce your attack and could muddy your sound—especially as you turn up the gain control.
10) MID The Mid control regulates the midrange frequencies and it is an important part of your tone shaping. The frequency range it boosts and cuts
has a big effect on the character of your sound. For a more scoopy tone, lower the mids. Turn the knob up for more focused attack and better pitch
definition.
11) HIGH The High knob controls the amount of high frequencies in your sound. It can produce unwanted noise (hiss) or pickup feedback when really
cranked, so it’s best to avoid extreme settings.
12) LEVEL (LEAD) This control is the master feed from the end of the preamp lead channel to the 250W MPT power amp. It allows you to obtain a
wide range of sounds/colours in relation to the gain setting—for example, very low gain sounds at high volumes, or high gain sounds at low volumes.
13) REVERB Level control for the onboard reverb. This amp features a last generation of digital reverb, it’s sweet-sounding, warm and natural.
14) FSW 1/4” jack for connecting a dual footswitch to switching between clean/lead channels and to turn on/off the reverb.
15) ON/OFF SWITCH This switch delivers AC power to the amp. The FG LITTLE 250 AMPLITUDE amps are manufactured to be used in the country
where they have been sold, and are factory preset to that country’s voltage. So make sure you’re sending the correct voltage to your amp before you
connect it to AC power and turn on the amp.
FRONT PANEL
TUNER OUT RETURN EFFECT SEND EFFECT
GND LIFTPOST EQ
PRE EQ
LINE OUT
BALANCED:
PIN1: GROUND
PIN2: SIGNAL +
PIN3: SIGNAL
SPEAKER OUT
1 + = SIGNAL
1 = GND
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
AVIS: RISQUE DE CHOC
ELECTRIQUE NE PAS OUVRIR.
CAUTION: RISK OF
ELECTRIC SHOCK DO NOT OPEN.
Model BIG BANG
CAUTION: FOR CONTINUED PROTECTION
AGAINST RISK OF FIRE REPLACE ONLY WITH
SAME TYPE AND RATING FUSE. TO REDUCE
THE RISK OF ELECTRIC SHOCK, GROUNDING
OF THE CENTRE PIN OF THIS PLUG MUST BE
MAINTAINED.
ATTENTION:
REMPLACER UNIQUEMENT
PAR UN FUSIBLE DE MEME TIPE.
Ser. Nr.
Date
120 ~ AC 60Hz T 6.3 A 250V Power 550W
MADE IN ITALY
PRE OUTRETURN EFFECT SEND EFFECT
0 dB
-6 dB
GAIN LOW
MID
HIGH LEVEL
GAIN LOW
MID
HIGH LEVEL
REVERB
ON
OFF
LEAD
CLEAN
FSW
CLEAN LEAD
519 20
21
17 18
16
22
1 2 5
4
3 6
9
8
10
11
12
7 13
14
15