DVTEL INC. 65 Challenger Road Ridgefield Park, NJ 07660 IOI-XTRK-10D Installation Manual The contents of this guide may not be reproduced or reprinted in whole or in part without the express written permission of DVTEL, INC.
IOI-XTRK-10D Installation Manual Table of Contents 1 Document Information.................................................................................................... iv 2 Introduction ................................................................................................................... 1 2.1 Items Included in the Package .................................................................................... 2 2.2 Hardware Overview .......................................................
IOI-XTRK-10D Installation Manual Appendix .............................................................................................................................22 A.1. Technical Specifications ............................................................................................ 23 A.2. Connecting Leads to a Spring Clamp Terminal Block ................................................. 25 A.3. Solo Setup Window ....................................................................................
Document Information List of Figures Figure 1 - IOI-XTRK-10D Unit ................................................................................................................... 1 Figure 2 - System Schematic .................................................................................................................... 2 Figure 3 - IOI-XTRK-10D Front Panel ....................................................................................................... 3 Figure 4 - Power Input Terminal ......
IOI-XTRK-10D Installation Manual 1 Document Information Document Scope and Purpose The purpose of this document is to provide instructions and installation procedures for physically connecting the IOI-XTRK-10D encoder. After completing the physical installation, additional setup and configurations are required before video analysis and detection can commence. For information on the unit setup and configuration, refer to the HTML Edition Units User’s Guide.
Document Information Disclaimer Users of DVTEL products accept full responsibility for ensuring the suitability and considering the role of the product detection capabilities and their limitation as they apply to their unique site requirements. DVTEL, Inc. and its agents make no guarantees or warranties to the suitability for the users’ intended use. DVTEL, Inc. accepts no responsibility for improper use or incomplete security and safety measures.
IOI-XTRK-10D Installation Manual To help ensure safety and to help reduce risk of injury or damage, observe the following: Warning: 1. Only qualified trained personnel should service and repair this equipment. 2. Observe local codes and laws and ensure that installation and operation are in accordance with fire, security and safety standards. Electrical Safety Notice and Warnings Warning: 1. Read the installation instructions before you connect the unit to a power source. 2.
Document Information Minimizing EMI and RFI When wires run for a significant distance in an electromagnetic field, electromagnetic interference (EMI) can occur. Strong EMI (e.g. lightning or radio transmitters) can destroy the units and can pose an electrical hazard by conducting power through lines and into the system. Poor quality or worn wiring can result in radio frequency interference (RFI). To minimize the effects of EMI and RFI, consult your reseller.
Introduction 2 Introduction The IOI-XTRK-10D is a self-contained video analytic IP encoder that monitors the video input from a camera, providing real-time detection and autonomous tracking capabilities. Operators can define rules, perimeter lines, sterile zones and other criteria for intrusion detection. In addition to its analytic capabilities, the IOI-XTRK-10D also transforms the input video to a standards-compliant, compressed IP video stream.
IOI-XTRK-10D Installation Manual As part of the ioimage intelligent video cameras series, the IOI-XTRK-10D‘s analog and IP streaming video outputs enable connectivity to both legacy analog DVR and IP-based network video management systems. The camera can be configured and setup via Internet Explorer 8 or 9 within a few minutes. Figure 2 - System Schematic 2.
Introduction 2.2 Hardware Overview This section provides a short description of the IOI-XTRK-10D front panel connections and features. Figure 3 - IOI-XTRK-10D Front Panel # Feature Description 1 Terminal block port 1 The terminal block includes: Inputs for connecting the RS485 control wires between the camera and the encoder (T+ and T-). Additional ground connection. 2 ETHERNET 802.
IOI-XTRK-10D Installation Manual Figure 4 - Power Input Terminal 7 Terminal block port 2 The terminal block includes a relay output, which supports output of optoisolated signal for a single external device, such as an electrical door lock relay.
Introduction Warning: The RS485 standard specifies an input voltage range between -7V to +12V. Exceeding this voltage can cause permanent damage to the unit.
IOI-XTRK-10D Installation Manual 3 Workflows The following are general workflows for installation as well as pre- and post-installation steps. The workflows are only guidelines. Individual installation may require variations based on the needs of the site. This section contains the following sections: Pre-Installation Workflow Installation Workflow Post-Installation 3.
Workflows 3.2 Installation Workflow Write down the unit’s IP address. Assemble the video cameras, associate equipment, and unit in the camera casing. Connect necessary internal wiring among the associated devices. Mount the video unit (includes mounting brackets, casing, camera, and encoder.) Note: Ensure necessary cooling, shelter and ventilation to maintain proper ambient environment.
IOI-XTRK-10D Installation Manual 4 Installation 4.1 Indoor and Outdoor Installation Considerations The following sections provide insight and key information that should be considered when installing the cabling for the IOI-XTRK-10D: Indoor Installation Outdoor Installation Caution: To avoid damage from overheating or unit failure, ensure that there is sufficient temperature regulation to support the unit’s requirements (cooling/heating).
Installation Rating Description IP54/NEMA 2 Protected against splashing water and the ingress of most dust. IP65/NEMA 4 Completely protected against the ingress of dust and against low pressure water jets from all directions, (limited ingress permitted), and to be undamaged by the formation of ice on the enclosure.
IOI-XTRK-10D Installation Manual 4.2.2 Electrical/Power Supply Cables Warning: 1. To prevent bodily injury or possible death, shut off the electrical current at the main switch before tying-in wiring. 2. Make sure that the product is properly grounded when in use. The following should be considered for electrical wiring and cables: 10 Electrical cabling must contain a grounding conductor. All electrical components and devices must be grounded for complete safety, especially for outdoor installations.
Installation 4.2.3 Electrical Power Input The unit must have the external protective earth terminal permanently connected to protective earth according to local regulations and codes. For more information, see Grounding the Unit (page 18). The protective grounding conductor should be aluminum. The lug of the protective grounding conductor should be aluminum; washers and screws should be Hi Cr stainless steel, 12% Cr stainless steel, Chromium on steel, Nickel on steel, tin, or steel.
IOI-XTRK-10D Installation Manual 4.2.3.1.1 Power Sourcing Equipment The power sourcing equipment (PSE) ensures that no damage can occur to any equipment on the network. The PSE first looks for devices that comply with the IEEE 802.3af specification. This is achieved by applying a small current-limited voltage to the cable. The PSE then checks for the presence of a 25k ohm resistor in the remote device.
Connections and Configuration 5 Connections and Configuration Installation of the encoder requires several steps described in the following sections: Connecting the Encoder (page 13) Configuring the Encoder’s Network IP Settings (page 19) Configuring Camera Settings via the Encoder (page 20) Resetting the Encoder (page 20) Solo Setup (page 21) 5.
IOI-XTRK-10D Installation Manual 5.1.1 Connecting the Camera to the Encoder The System Cable supplied with the CP-2202-361P/N PTZ camera connects the IOI-XTRK-10D encoder to the camera’s video output and RS485 control line. The following illustration shows the System Cable: Figure 6 - System Cable 5.1.1.
Connections and Configuration 5.1.1.2 Connecting the Camera’s PTZ Control Line to the Encoder Use a two-wire 24 AWG cable (not supplied by DVTEL) to enable the RS485 control connection between the encoder and the camera.
IOI-XTRK-10D Installation Manual Relay Output Specifications Maximum current 1A @ 24VDC Maximum current 0.5A @ 125VAC 5.1.2.
Connections and Configuration 5.1.3 Connecting the Encoder’s Video Output to an Analog Device The encoder’s analog video output can be monitored or recorded on analog devices. The output analog video contains the video from the camera combined with On-Screen Display (OSD) overlays such as tracking boxes and trails, time stamp, alarm, camera status, etc. These OSD overlays can be enabled and customized using the HTML setup application. For more information, refer to the HTML Edition Units User’s Guide.
IOI-XTRK-10D Installation Manual 5.1.5 Connecting a Loudspeaker to the Unit Use the supplied audio splitter cable to connect a loudspeaker to the unit and make announcements near the camera from a microphone connected to the Video Management System PC. The audio output from the unit provides Line Out levels. An amplifier must be used to drive the loudspeakers. Figure 10 - Loudspeaker Connection to the Unit Note: AUDIO OUT cannot be enabled from the unit’s web interface.
Connections and Configuration 5.1.7 Connecting the Unit to the Power Supply Connecting the electrical power to the unit is recommended as the last physical connection to be made before connecting the encoder to the network. Before connecting to the power, please review Indoor and Outdoor Installation Considerations (page 8) and Electrical/Power Supply Cables (page 10). Electrical safety should always be observed.
IOI-XTRK-10D Installation Manual 5.3 Configuring Camera Settings via the Encoder The encoder’s web interface is used to configure the CP-2202-361P/N camera. To configure the camera 1. From the Setup window, select Camera > Type & Model. Figure 11 - Type & Model Setup Window 2. Check Enable Re-arm. If the camera was previously armed, this function returns the camera to Armed status after the user releases manual control of the camera. 3.
Connections and Configuration To reset a board using the RESET button 1. Insert a small pointed object into the hole labeled RESET on the front panel of the unit. 2. Press in and release. The unit resets to the previous settings. 5.4.2 Reset by Removing the Power Supply The unit can be reset by turning off the power and then turning it on again. To reset a unit by removing the power supply 1. Turn off or disconnect the power to the unit. 2. Turn on or reconnect the power to the unit.
IOI-XTRK-10D Installation Manual Appendix The appendix contains the following sections: 22 Technical Specifications (page 23) Connecting Leads to a Spring Clamp Terminal Block (page 25) Solo Setup Window (page 26) Troubleshooting (page 29 )
Appendix A.1.
IOI-XTRK-10D Installation Manual Physical Dimensions Dimensions (mm) 75 x 55 x 118 mm (W x H x D) Dimensions (inches) 2-15/16” x 2-5/32” x 4-5/8” (W x H x D) Mounting Camera housing/Shelf-mount Environmental Specifications Operating Temperature 0° to 50°C (32° to 122°F) Operating Humidity 5% to 95% (non-condensing) Certifications Safety UL, CE Electromagnetic Interference (EMC) FCC 47 CFR part 14 subpart B, Class A, CE, Class A Environmental RoHS 24
Appendix A.2. Connecting Leads to a Spring Clamp Terminal Block The encoder comes with two terminal block connectors. Each connector is for terminating wires and then plugging the connector into the relay output of the encoder. Figure 12 - Installed Terminal Block Connector To connect a wire to the spring clamp terminal block 1. Strip the insulation form the end of each wire that is to be connected to the terminal block. Approximately 1 cm (2.54”) of wire should be exposed. 2.
IOI-XTRK-10D Installation Manual A.3. Solo Setup Window The Solo Setup function enables you to install and setup a camera without requiring another person’s assistance. To perform a Solo Setup 1. Open the Setup > Analytics > Depth window.
Appendix 2. Open the Solo Setup tab. The following control icons are available on the Solo Setup keypad: Icon Function Notes Start Recording Starts recording and browses to destination folder where the clip will be saved Stop Recording Stops recording Browse Browses to the destination folder where clip is stored and loads the clip Play/Pause Speed X1/X0 Fast Forward Speed X2, X4, X8, X16. Click to increase or decrease speed. Rewind Speed -X2, -X4, -X8, -X16.
IOI-XTRK-10D Installation Manual 10. Exit Clip mode and return to Live mode by pressing the round Play button on the control panel located to the left of the monitor. The caption under the monitor changes from Clip to Live. 11. Repeat steps 3-9 above for each preset. 12. Proceed to the tabs for Steps 2-4 of the Depth Setup to complete the setup and apply settings.
Appendix A.4. Troubleshooting This section provides useful information and remedies for common situations where problems may be encountered. Problem Try No Ethernet 10/100 status LED when Ethernet is connected (other LEDs are OK). Hardware issues: Check that the network is working and the unit is powered on. Check that the network (Ethernet) cable is properly attached to the unit. Confirm that the LED on the Ethernet (RJ-45) connector on the power connection panel of the unit is on.
IOI-XTRK-10D Installation Manual Problem Try IP shows on the LAN/WAN but communication between units and DVTEL applications is blocked. The DHCP has changed the encoder IP and given the initial IP to a different device. Because DHCP is a dynamic agent that provides IPs to requestors there is a possibility that an IP can be mistakenly given away. Consult your network administrator about preventing this situation.
Appendix Problem Try Streaming video image is hanging (stopped). The PTZ camera control doesn’t work. Relay Output is not working. Refresh browser screen (F5). Confirm the unit’s video streaming settings. Refer to the HTML Edition Units User’s Guide for details. Check that the network is operating correctly. Check that the HTML setup configuration is correct for the available CPU and network traffic.
IOI-XTRK-10D Installation Manual Contacting DVTEL To contact us, write us at info@dvtel.com or contact your local office. CORPORATE HEADQUARTERS DVTEL, Inc. 65 Challenger Road Ridgefield Park, NJ 07660 USA Tel: 201.368.9700 Fax: 201.368.2615 Order Fax: 201.712.
