Installation Sheet

ManualsBrandsDXV ManualsPlumbingBelshire 30-Inch Vanity Natural Oak

- 1 -

INSTALLATION INSTRUCTIONS

SAVE FOR FUTURE USE

Product names listed herein are trademarks of AS America, Inc.

7302420-100 Rev. A (6/2020)

RECOMMENDED TOOLS AND MATERIALS

Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing

supply stores. It is essential that the tools and materials be on hand before work has begun.

Thank you for selecting DXV. To ensure this product is installed properly, please read these instructions carefully before you begin.

(Certain installations may require professional help.) Also be sure your installation conforms to local codes.

To maintain the beauty of the nish, avoid placing the furniture in direct sunlight, as sunlight causes fading. Also avoid extreme

changes in temperature by arranging furniture away from radiators, heat and air vents, and air conditioning units. Avoid placing

furniture directly under windows.

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

Models D19085030, D19086030

DXV Belshire

™

Vanity

VANITY INSTALLATION

• Unpack unit carefully, taking care not to damage

corners, unit is heavy.

• Provide suitable 2x6 reinforcement required for anchoring

the vanity to the wall using the vanities cleat.

• Ensure roughin water supply lines and drain correctly

t within openings of vanity. Suitable space is provided for this.

Remove vanity drawers which will aid moving and handling of

vanity and to provide room to connect water supply lines and

drain. To do so, open top drawer rst and pull orange tab (under

drawer) towards the center of drawer on both left and right sides

which will release the drawer from the side rails or tracks. Pull

drawer up and out. Repeat for other drawer(s).

Carefully unpack marble top and lay on a protective cushioned surface to avoid any possible scratching

or chipping (marble top is heavy).

NOTE: Bottom side of marble has threaded inserts.

NOTCH STUDS

OR TOE-NAIL

DRAIN PIPE

WATER

SUPPLY

PIPES

VANITY

CROSS-PIECE

SUPPORT

INSTALLING

CROSS-PIECE

For rough-in dimensions and supply line information, see spec page or web site

10'

Electric

Drill

Tape Measure

Level

Square

Phillips Screwdriver

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS DXV Belshire™ Vanity Models D19085030, D19086030 Thank you for selecting DXV. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes. To maintain the beauty of the finish, avoid placing the furniture in direct sunlight, as sunlight causes fading.
PAGE 2
3 Carefully unpack lavatory and place in the center of opening on the underside of the marble top as an under counter mount installation. Ensure lavatory is centered evenly over underside of marble top opening front to back, side to side and trace a pencil line around the perimeter of the lavatory onto the underside of the marble top. 4 Remove lavatory and apply silicone sealant around the traced pencil line of the marble top.
PAGE 3
9 Screw vanity into cross support behind the wall to firmly attach vanity to the wall. Place assembled combination of marble counter top and lavatory onto top of vanity. Ensure marble top is flush to rear of wall and centered left to right over the vanity and check level front to back, left to right. Also check that drain and water supply lines correctly fit when drawers are installed.
PAGE 4
Vanity Legs Model D19087000 Series NOTE: Vanity legs are optional and need to be purchased and considered before the actual installation of the vanity to ensure height dimensions are correct for water supply lines and waste drain. LEG INSTALLATION • Carefully place vanity on its back side to expose the underside/bottom of the vanity. • Threaded mounting holes for supplied screws are installed on both sides of the vanity. • Vanity legs are screwed in place with the supplied screws on each side.