Installation Sheet

- 3 -
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
WARNING Do not use plumber’s putty, pipe dope, or any other sealant on the water supply connection to this tank.
If the connection leaks after hand tightening, replace the supply line. If the connection continues to leak with the new
supply line, replace the ll valve.
Warranty is void if any type of sealant is used on the water supply connection.
7
8
9a
10
7302031-100 Rev. C (6/17)
INSTALL TOILET
!
For Tanks/Bowls using Speed Connect System (Tank mounting bolts pre-installed).
a. Install large rubber gasket over threaded outlet on bottom of tank and
lower tank onto bowl so that tapered end of gasket ts evenly into bowl
water inlet opening, and tank mounting bolts go through mounting
holes. Secure with metal washer/nut combo.
b. With tank parallel to wall, alternately tighten nuts until tank is snugged
down evenly against bowl surface.
*
USE INCLUDED TOOL, NUT DRIVER, OR DEEP SOCKET RACHET.
CAUTION: DO NOT OVERTIGHTEN NUTS MORE THAN
REQUIRED FOR A SNUG FIT!
Before continuing, determine the type of water supply connection you have from
the chart below and use the appropriate assembly parts required to properly
reconnect the water supply. DO NOT use plumber's putty to seal these ttings.
METAL/COPPER
FLARED TUBING
METAL FLANGED
TUBING
METAL SPIRAL
TUBING
VINYL/BRAIDED
CONNECTOR
LOCK NUTLOCK NUT LOCK NUT LOCK NUT
COUPLING
NUT
COUPLING
NUT
EXISTING
COUPLING
NUT
COUPLING
NUT
WATER
SHUT-OFF
WATER
SHUT-OFF
WATER
SHUT-OFF
WATER
SHUT-OFF
CONE
WASHER
EXISTING
CONE
WASHER
EXISTING
WASHER
These parts must be used as illustrated
to insure water-tight connection. Use
of existing coupling nut may result in
water leakage. Water supply tube or
pipe must extend at least 1/2" (13 mm)
inside threaded shank of valve (does
not apply to anged tubing).
Use existing spiral cone
washer. Fluidmaster cone
washer may not seal
completely on spiral
type supply line.
Captive cone washers
already included. No
additional washers
needed.
Use existing
coupling nut
and washer.
9b
11
CAUTION: DO NOT USE CONE
WASHER WITH PLASTIC SUPPLY LINE.
With correct washers in place (see
Step 9a), tighten COUPLING NUT
1/4 turn beyond hand tight.
DO NOT OVERTIGHTEN.
CAUTION: Overtightening of LOCK NUT
or COUPLING NUT could result in
breakage and potential flooding.
RUBBER
GASKET
TANK MTG.
BOLTS PRE-
INSTALLED
WASHER/
NUT
COMBO
!
ADJUSTMENTS
a. Adjust water level. Water level
should be adjusted to level
indicated on tank by adjusting
oat cup.
See Step 11 for water level
adjustment method.
b. If bowl fails to siphon, an
adjustment may be required
with the lift chain. Simply
remove the bead chain from the
retainment clip (see Diagram 1)
and take up slack on the chain,
and reinsert on lift rod. Make
sure the chainis not too taught.
Turn on water supply.
Submerge the FLOAT CUP
under the water for 30
seconds. Adjust the water
to desired level by turning
WATER LEVEL ADJUSTMENT
ROD and moving FLOAT CUP
up or down.
VALVE
BODY
ADJUSTABLE
HEIGHT
WATER LEVEL
ADJUSTMENT
ROD
TANK
LEVER
FLUSH
VALVE
TOP
ARM
NIPPLE
Diagram 1
PARTS FOR WATER
CONNECTION
(SEE STEP 9)
CONE WASHER
FLAPPER
THREADED
SHANK
SHANK
WASHER
COUPLING NUT
(HAND TIGHT ONLY)
FILL
VALVE
F L O AT
CUP
CRITICAL LEVEL
MARK ("C.L.")
MUST BE
1" ABOVE
OVERFLOW PIPE
REFILL
TUBE
LOCK NUT