Installation Sheet
- 2 -
7302031-100 Rev. C (6/17)
2b
INSTALL CLOSET BOLTS
Install closet bolts in ange channel,
turn 90°, and slide into place 6"
(152 mm) apart and parallel to wall.
INSTALL WAX SEAL
Invert toilet on oor (cushion to
prevent damage), and install wax
ring evenly around waste ange
(horn), with tapered end of ring
facing toilet. Apply a thin bead
of sealant around toilet base.
POSITION TOILET ON FLANGE
a. Unplug oor waste opening and install toilet
on closet ange so bolts project through
mounting holes.
b. Loosely install retainer washers and nuts.
Side of washers marked "THIS SIDE UP"
must face up!
3
6
4 5
CLOSET FLANGE
DRAIN
CENTER LINE
3/8" (10 mm) -16 HEADLESS
HANGER BOLTS
5" (127 mm)
CLOSET BOLTS
5" (127 mm)
7" (178 mm)
INSTALL TOILET
CLOSET BOLT
NUT
BOLT COVER
Peel both protective lms off
and stick bolt cover to toilet.
Back Side
Front Side
BOLT COVER
BOLTS
CLOSET FLANGE
!
a. Position toilet squarely to wall and, with a rocking
motion, press bowl down fully on wax ring and ange.
Alternately tighten nuts until toilet is rmly seated on oor.
CAUTION: DO NOT OVERTIGHTEN NUTS OR
BASE MAY BE DAMAGED!
b. Install bolt covers:
1. Make sure that the bolt cover area on the toilet is
clean and dry (see gure). Use a dry piece of cloth
or soap and waterif needed.
2. Take plastic bolt cover and peel the brown protective
lm off on both ends. The adhesive part is now visible
and ready to be placed on the toilet (see gure).
3. Gently place the bolt cover on the toilet area (see picture) and if everything is aligned, push bolt cover
rmly so it remains in place.
4. If not aligned, you can still take it off and put it back so it is aligned.
5. Repeat Step 3 for second bolt cover which is to be placed on opposite side of the toilet.
6. After 24 hours, the bolt cover adhesive has completely set off and if needed, you can remove/replace
as needed. The dual lock technology is now in place.
c. Smooth off the bead of sealant around base. Remove excess sealant.
IMPORTANT: Water
supply on the wall is
required at 3" (76 or
229 mm) from centerline
of the toilet (see rough-in).
First suggested position
is hidden behind the toilet.
The geometry of the toilet
gives space for this
installation. The second
suggested position is
next to the toilet.
Between these two
positions, the space
for the supply between
wall and toilet is limited
to 3-1/2" (89 mm). In this
case, check your supply
and hose dimensions.
ROUGHING-IN DIMENSIONS: NOTE: Distance from wall to closet flange centerline must be as listed below:
27-7/8"
(708 mm)
7-7/16"
(189 mm)
1"
(26 mm)
16-1/2"
(419 mm)
3-1/2"
(88 mm)
2-3/4"
(70 mm)
3-3/8"
(85 mm)
70 C
L
8-9/16"
(217 mm)
13-11/16"
(348 mm)
16-1/2"
(419 mm)
15-1/16"
(383 mm)
31-3/16"
(792 mm)
12"
(305 mm)
FINISHED
FLOOR
C/L OF SEAT POST
HOLES 5-1/2"
(140mm) CENTERS
SUPPLY
AS
REQUIRED
(position 1 or
position 2)
6"
(152 mm)
5-1/2"
(140 mm)
14"
(356 mm)
9"
(229 mm)
3"
(76 mm)
13-1/2"
(342 mm)
12-3/8"
(315 mm)
Model# D2205DA101
WAX RING
SEALANT
NUT
TAPERED
WASHER
FLANGE
CLOSET
BOLT