Installation Sheet

ManualsBrandsDXV ManualsBathroom FaucetsRandall 1.2 GPM Single Hole Bathroom Faucet with Pop - Up Drain Assembly

- 1 -

INSTALLATION INSTRUCTIONS

Product names listed herein are trademarks of AS America, Inc.

SAVE FOR FUTURE USE

RECOMMENDED TOOLS AND MATERIALS

Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing

supply stores. It is essential that the tools and materials be on hand before work is begun.

M965704 Rev. 1.1 (2/17)

Lavatory

Model D3510210C

Vessel

Model D3510215C

Model D3510216C

Randall

Single Lever Lavatory

and Vessel Faucets

ROUGHING-IN DIMENSIONS:

• For reference

• NOTE: MOUNTING HOLES ARE 1-3/8" D.

4-3-16"

(106 mm)

4-1/4"

(108 mm)

8-1/2"

(216 mm)

MTG.

SURFACE

24"

(610 mm)

(152 mm)

1-3/4" (45 mm)

2-3/4" DIA.

(70 mm)

3/8" (10 mm)

SUPPLIES

12" MAX.

(305 mm)

MAX 2"

(51mm)

1-1/4" O.D.

(32 mm)

NOTE: MOUNTING HOLE

1-3/8" DIA. (35 mm)

12-5/16"

(316 mm)

4-1/8"

(105 mm)

8-1/8"

(206 mm)

3-1/16" DIA.

(77 mm)

(152 mm)

MTG.

SURFACE

24"

(610 mm)

2-1/16" MAX. (53 mm)

12" MAX.

(305 mm)

MAX 2"

(51 mm)

1-1/4" O.D.

(32 mm)

3/8" (32 mm)

SUPPLIES

Flat Blade Screwdriver Plumber’s Putty or CaulkingAdjustable Wrench Tubing Cutter Channel Locks

In the United States:

DXV

One Centennial Avenue

Piscataway, New Jersey 08855

Attention: Director of Customer Care

For residents of the United States, warranty

information may also be obtained by calling

the following toll free number: (800) 227-2734

www.DXV.com

In Canada:

DXV

5900 Avebury Road

Mississauga, Ontario

L5R 3M3

Canada

Toll Free: 1-800-387-0369

Local: 905-306-1093

Fax: 1-800-395-1498

www.DXV.ca

In Mexico:

DXV

Via Morelos 330

Col. Santa Clara Coatitla

Ecatepec, Estado de México 55540

Toll Free: 01-800-8391200

www.DXV.mx

Thank you for selecting DXV. To ensure that your

installation proceeds smoothly, please read these

instructions carefully before you begin.

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Randall® Single Lever Lavatory and Vessel Faucets Lavatory Model D3510210C Vessel Model D3510215C Model D3510216C Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing supply stores. It is essential that the tools and materials be on hand before work is begun.
PAGE 2
1 INSTALL FAUCET (LAVATORY AND VESSEL FAUCETS) CAUTION Turn off hot and cold water supplies before beginning. • Install O-RING (1) into O-ring groove of FAUCET BASE (2). • Feed FAUCET SUPPLY TUBES (5) and SHANK (3) and DRAIN CABLE ASSEMBLY (9) through mounting hole of lavatory or mounting surface. • From below, Install RUBBER SEAL with RETAINING WASHER (4) and LOCKNUT (6) onto faucet SHANK (3). Before final tightening, faucet should be seated flush on mounting surface.
PAGE 3
2 POP-UP DRAIN Fig. A. Fig. B. • Remove CLEAR PLASTIC COVER (1). Fig. A. 1 • Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). Fig. A. 3 • Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. DRAIN BODY 2 3 REMOVE FLANGE 4 Fig. A. • Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Fig. B. 1 • Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
PAGE 4
7 ATTACH CABLE CONNECTOR Fig. A. Fig. B. • Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. 1 • Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4" (32 mm) O.D. Fig. B. 2 1-1/4” O.D. 8 CHECK OPERATION OF POP-UP • Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.
PAGE 5
10 TEST INSTALLED FITTING • With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. • Remove AERATOR (3). • Operate HANDLE (1) to flush water lines thoroughly. • Replace AERATOR (3). CHECK DRAIN CONNECTIONS • Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in sink. If DRAIN STOPPER (5) does not seal properly, please refer to Troubleshooting section in these instructions.
PAGE 6
Speed Connect® Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 7
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Fig. G. LOCKED MODE: • Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. • To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink.
PAGE 8
Randall® Single Lever Lavatory and Vessel Faucets MODEL NUMBERS Lavatory D3510210C Vessel D3510215C D3510216C A860811.XXX HANDLE ASSEMBLY M964733-YYY0A CAP AND NUT A860621.