Installation Sheet

ManualsBrandsDXV ManualsBathroom FaucetsEquility 1.2 GPM Widespread Bathroom Faucet

- 1 -

INSTALLATION INSTRUCTIONS

Product names listed herein are trademarks of AS America, Inc.

SAVE FOR FUTURE USE

RECOMMENDED TOOLS AND MATERIALS

Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing

supply stores. It is essential that the tools and materials be on hand before work is begun.

M965850 (8/17)

Model D35109800

Lyndon

Widespread

Lavatory Faucet

Plumbers' Putty or Caulking

Phillips Screwdriver

Channel LocksTubing Cutter Flat Blade Screwdriver Adjustable Wrench

Basin Wrench

ROUGHING-IN DIMENSIONS:

• For reference

1-1/4" MAX.

(32 mm)

1-1/16" DIA.

(27 mm)

1-1/4" O.D.

(32 mm)

1-3/4"

(45 mm)

(203 mm)

1-1/2" MAX.

(38 mm)

3-9/16"

(91 mm)

5-3/8"

(137 mm)

4-1/2"

(115 mm)

6-3/16"

(156 mm)

6-15-/16"

(177 mm)

1-9/16"

(40 mm)

2-1/16" DIA.

(53 mm)

13-15/16"

(353 mm)

7/8" DIA.

(22 mm)

NOTE: MOUNTING HOLES

ARE 1-3/8" DIA. (35 mm)

CONNECTIONS:

• 1/2" IPS FLEXIBLE SUPPLIES

• 3/8" O.D. BULL-NOSE RISERS

In the United States:

DXV

One Centennial Avenue

Piscataway, New Jersey 08855

Attention: Director of Customer Care

For residents of the United States, warranty

information may also be obtained by calling

the following toll free number: (800) 227-2734

www.DXV.com

In Canada:

DXV

5900 Avebury Road

Mississauga, Ontario

L5R 3M3

Canada

Toll Free: 1-800-387-0369

Local: 905-306-1093

Fax: 1-800-395-1498

www.DXV.ca

In Mexico:

DXV

Via Morelos 330

Col. Santa Clara Coatitla

Ecatepec, Estado de México 55540

Toll Free: 01-800-8391200

www.DXV.mx

Thank you for selecting DXV. To ensure that your

installation proceeds smoothly, please read these

instructions carefully before you begin.

Summary of content (5 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Lyndon® Widespread Lavatory Faucet Model D35109800 RECOMMENDED TOOLS AND MATERIALS Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing supply stores. It is essential that the tools and materials be on hand before work is begun. U S E Thank you for selecting DXV. To ensure that your installation proceeds smoothly, please read these instructions carefully before you begin.
PAGE 2
1 SPOUT ASSEMBLY CAUTION Turn off hot and cold water supplies before beginning. 8 • Insert SPOUT SHANK (1) through center hole of sink or mounting surface. Make sure RUBBER WASHER (2) is seated into groove in SPOUT ESCUTCHEON BASE (3). 7 3 • Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto threads of SPOUT SHANK (1) from underside of lavatory or mounting surface. GROOVE 2 • Align SPOUT (7) and tighten LOCKNUT (6). Insert LIFT ROD (8) through SPOUT (7).
PAGE 3
4 INSTALL POP-UP DRAIN 1 4a 1 • Drop FLANGE (1) into LAVATORY DRAIN (2). From below assemble RUBBER GASKET (3), METAL WASHER (4) and LOCK NUT (5). Do not tighten. • Apply a bead of putty to underside of FLANGE (1). 2 3 4 5 4c 4b • Place SEAL (1) with small end facing up into TAILPIECE (2) and tighten against DRAIN BODY (4). PIVOT ROD (3) opening in TAILPIECE (2) should face the rear of the lavatory. Tighten LOCK NUT (5) with channel locks.Do not over tighten.
PAGE 4
11 6 MAKE WATER SUPPLY AND WASTE CONNECTIONS NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED AND MUST BE PURCHASED SEPARATELY. • Connect water supply to VALVE BODIES (1,1A) with 1/2" IPS FLEXIBLE SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3). Use adjustable wrench to tighten connections. Do not over tighten. Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length.
PAGE 5
Lyndon® Widespread Lavatory Faucet MODEL NUMBERS D35109800 Replace the “YYY” with appropriate finish code M970368-YYY0A LIFT KNOB & ROD POLISHED CHROME 100 BRUSHED NICKEL 144 PLATINUM NICKEL 150 MATTE BLACK 243 M970373-0070A AERATOR KIT (1.