Installation Sheet

ManualsBrandsDXV ManualsBathroom FaucetsDXV Modulus 1.2 GPM Single Hole Vessel Bathroom Faucet

- 1 -

INSTALLATION INSTRUCTIONS

(228 mm)

6-15/16"

(160 mm)

5-5/16"

(135 mm)

10-11/16"

(271 mm)

9-5/8"

(244 mm)

1-5/16"

(33 mm)

1-5/16"

(33 mm)

NOTE: MOUNTING HOLES ARE

1-3/8" D. (35 mm)

2-3/8"

(60 mm)

2-9/16"

(65 mm)

2-3/8"

(60 mm)

6-15/16"

(160 mm)

5-5/16"

(135 mm)

5-7 /16"

(138 mm)

3-5/16"

(84mm)

3-15/16"

(99 mm)

(127 mm)

2-3/8"

(60 mm)

5-3/16"~7-11/16"

(131~195 mm)

1-1/4" O.D.

(32 mm)

Product names listed herein are trademarks of AS America, Inc.

SAVE FOR FUTURE USE

RECOMMENDED TOOLS AND MATERIALS

Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing

supply stores. It is essential that the tools and materials be on hand before work has begun.

M965829 (4/17)

Monoblock Vessel

Model D35120152

Monoblock

Model D35120102

Modulus

™

Single Lever Faucet

Flat Blade Screwdriver Plumber’s Putty or CaulkingAdjustable Wrench Tubing Cutter Channel Locks

ROUGHING-IN DIMENSIONS:

NOTE: Mounting holes are 1-3/8" D.

In the United States:

DXV

One Centennial Avenue

Piscataway, New Jersey 08855

Attention: Director of Customer Care

For residents of the United States, warranty

information may also be obtained by calling

the following toll free number: (800) 227-2734

www.DXV.com

In Canada:

DXV

5900 Avebury Road

Mississauga, Ontario

L5R 3M3

Canada

Toll Free: 1-800-387-0369

Local: 905-306-1093

Fax: 1-800-395-1498

www.DXV.ca

In Mexico:

DXV

Via Morelos 330

Col. Santa Clara Coatitla

Ecatepec, Estado de México 55540

Toll Free: 01-800-8391200

www.DXV.mx

Thank you for selecting DXV. To ensure that your

installation proceeds smoothly, please read these

instructions carefully before you begin.

D35120152

D35120102

Summary of content (6 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Modulus™ Single Lever Faucet Monoblock Vessel Model D35120152 Monoblock Model D35120102 Thank you for selecting DXV. To ensure that your installation proceeds smoothly, please read these instructions carefully before you begin. D35120152 Adjustable Wrench Channel Locks Tubing Cutter Flat Blade Screwdriver ROUGHING-IN DIMENSIONS: NOTE: Mounting holes are 1-3/8" D.
PAGE 2
1 INSTALL FAUCET (LAVATORY AND VESSEL FAUCETS) CAUTION Turn off hot and cold water supplies before beginning. • Install SEAL (1) into groove of FAUCET BASE (2). • Feed FAUCET SUPPLY TUBES (5) and SHANK (3) through m ounting hole of lavatory or mounting surface. • From below, Install RUBBER SEAL with RETAINING WASHER (4) and LOCKNUT (6) onto faucet SHANK (3). Before final tightening, faucet should be seated flush on mounting surface. Adjust faucet so that it is centered and covers mounting hole.
PAGE 3
2 DRAIN INSTALLATION • Apply a bead of PUTTY to underside of DRAIN BODY FLANGE (1). 1 • Feed DRAIN BODY (1)) down through lavatory. • Assembly GASKET (2) WASHER (3) and LOCKNUT (4) onto DRAIN BODY (1). Tighten LOCKNUT (4) firmly. PUTTY • Assembly TAILPIECE (5) to DRAIN BODY (1). 2 3 4 5 3 MAKE WATER SUPPLY AND WASTE CONNECTIONS • Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection on fitting supplies are 3/8" (10 mm) compression.
PAGE 4
TEST INSTALLED FITTING • With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. • Operate HANDLE (1) to flush water lines thoroughly.
PAGE 5
MAINTANENCE If water flow rate is lower than stated, flow regulator might be clogged by debris in the water lines. Clean filter screen at inlet hoses. TO REPLACE FLOW REGULATOR • Turn water supplies off. • Use a SHARP TOOL (1) to loosen DECORATIVE RING (2). Figure A. • Lift up DECORATIVE RING (2) and use hex key to remove SET SCREW (3). Figure B. • Remove BASE (4) and pull whole handle assembly off. Figure B. • Unthread CARTRIDGE NUT (5) to remove CARTRIDGE (6). Figure C.
PAGE 6
Modulus™ Single Lever Lavatory and Vessel Faucets MODEL NUMBERS Vessel Faucet D35120152 Lavatory Faucet D35120102 M970297-YYY0A HANDLE KIT FOR D35120152 M970296-YYY0A HANDLE KIT FOR D35120102 Replace the “YYY” with appropriate finish code POLISHED CHROME 100 BRUSHED NICKEL 144 PLATINUM NICKEL 150 M970300-0070A CARTRIDGE KIT M964502-0070A FLOW RESTRICTOR KIT M970299-YYY0A SET SCREW KIT D35120152 D35120102 D35120460.