Installation Guide

ManualsBrandsDyconn Faucet ManualsBathroom Sink FaucetsBrushed Nickel 1-Handle Single Hole Bathroom Sink Faucet

Product Features:

Durable Solid-Brass Construction

Drip Free Ceramic Disc Cartridge for

Smooth and Long Lasting Operation.

Contemporary Design

3-Year Manufacturer Warranty

Thoroughly read all instructions before installing the enclosed product.

Read and take note of all safety, care, and maintenance information.

Contemporary Vessel Sink Faucet

Models: Wade VS1H23A, Beck, Conway, Kai, Marsh, Maya VS1H28A

Hurley, Cove, Maris, Calder VS1H39A

For easy installation of your Dyconn Faucet please do the following:

Summary of content (10 pages)

PAGE 1
Product Features: Durable Solid-Brass Construction Drip Free Ceramic Disc Cartridge for Smooth and Long Lasting Operation. Contemporary Design 3-Year Manufacturer Warranty Contemporary Vessel Sink Faucet Models: Wade VS1H23A, Beck, Conway, Kai, Marsh, Maya VS1H28A Hurley, Cove, Maris, Calder VS1H39A For easy installation of your Dyconn Faucet please do the following: Thoroughly read all instructions before installing the enclosed product.
PAGE 2
Faucet Parts & Accessories You may need the following tools/materials Valve Hoses (included) Pliers Screw Driver Silicone Wrench Plumbers Tape Daily Maintenance 1. Use a soft cloth and vinegar to remove hard water spots. 2. Check aerator (if present) regularly for calcium build up when water stream is not optimal. 3. DO NOT use caustic cleaning products as the use will break down ﬁnish and will void the product warranty. 4. Acceptable cleaners include vinegar or mild non-abrasive liquid detergents.
PAGE 3
Product Dimensions (VS1H23A) Depth 6” Spout reach 4 7⁄16” Height 7 ¼” Spout Height 3 15⁄16” Width 1 ¾” 2
PAGE 4
Product Dimensions (VS1H28A) Depth 6” Spout reach 4 7⁄16” Height 7 ½” Spout Height 5 11⁄16” Width 3 15⁄16” 3
PAGE 5
Product Dimensions (VS1H39A) Depth 6” Spout reach 4 5⁄16” Height 7 ¼” Spout Height 3 15⁄16” Width 1 ¾” 4
PAGE 6
Installation Instructions Diagram 1 1.25” (30mm) 1.5” (38mm) Note: Your faucet is designed for a hole with a diameter of 1 1/4” (30mm) and a deck thickness of up to 1 1/2” (38mm). Diagram 2 2 1 3 4 5 Step 1: Unscrew the shank (1) from the faucet (if it is connected) and place it to the side, along with the faucet base (2), gasket (3), washer (4) and mounting nut (5).
PAGE 7
Installation Instructions Diagram 3 1 2 Step 2: Attach both water hoses to the faucet by screwing them into the two internal ports located inside the base of the faucet. The red/blue indicator on the side of the handle illustrates the hot water hose (red - 1) is attached to the left port while the cold water hose (blue -2) is attached to the right port. Diagram 4 2 1 Step 3: Attach the shank (1) and base (2) and proceed to install the faucet through the deck mounting hole.
PAGE 8
Installation Instructions Diagram 5 1 2 3 Step 5: Install the rubber gasket (1), washer (2) and the mounting nut (3) onto the faucet shank. Tighten the screws on the mounting nut to secure the mounting nut and the faucet in place. Be sure the large side of the mounting nut is facing up and the screws are pointing upward. Diagram 6 Step 6: Connect both water hoses onto the respective water valves (we recommend using plumbers tape to prevent leakage). Turn on the water valves.
PAGE 9
Installation Instructions Diagram 7 Step 7: plumbing pipes. This debris can damage the internal faucet surfaces which can cause leakage. Before turning on the water valves, make sure the faucet Diagram 8 Step 8: seconds. Evaluate all connections for leakage. After this process is complete, you may proceed to use your new faucet.
PAGE 10
Manufacturer Limited Warranty All Dyconn Faucet products are manufactured and tested with the highest quality standards and rigorous quality control process. This warranty is limited to the non-commercial use of Dyconn Faucet products purchased and installed in the United States and Canada.