Smart toilet seat Manual The Product Model: Contents Thanks for choosing our product. Overall sketch 1 Safety precautions 2 Function introduction 4 Installation guide 5 And please read the instructions carefully before properly using.
Safety Precautions Overall sketch All the safety precautions listed can prevent the users from the physical hurts or property losses. Please read all the safety items and warnings, using the product in the right way. Cushion pad WARNING Ignoring the sign may lead to serious injury or death. Damper Toilet lid Don’t disassemble, repair, alter the product. Warm air dryer All the behaviors above may lead to fire or electric shock. Control panel Don’t immerse the product into the water.
Function introduction: WARNING Ignoring the sign may lead to serious injury or death. Functions Don’t stand on the toilet seat cover, seat circle or any other accessories. It may cause break down the product. Don’t drag or bend the water pipe. It may make water leakage or no water supply. Preventing damage from freeze. The inlet tube and the inner of the product may be damaged for freezing, and then lead to water leakage. Don’t put heat instruments beside the substance.
Installation Guide Install bidet Installation environment 1、Before installation,toilet wall,floor tile,ceramic toilet has been completed, bathroom should advance water and 110V 15A power socket near by toilet. 2、Water pressure should be between 0.06Mpa(flow)-0.75MPa (Static),water temperature 4℃-35℃. 3、Fozen case, please put the product in a warm place wait to melt then install it. 4、Connect daily-use water pipe only.
Preparation for water supply and Test for operation Install bidet Install bidet Push the product slip into fix bracket and left bidet to send it into fitter place Notice: please don't forget the power cable between the toilet and bidet. Be sure the bidet fixed as complete then left bidet to fit it on correct position. connect inlet pipe 1、Insert electric plug into the socket.
Operations Operation introduction Product use manual This product is controlled mainly by remote control, while by control panel subsidiary Please note below picture is only for illustration that how LED displays in full screen, not the actual interface. 1.Sitting on the toilet seat seated-sensor activated If air purification is activated,deodorizing function operates automatically. 2.Rear wash Rear cleansing (Icon as below displays in the screen) LED Display (Except Model 228ZA) 5.
.Dryer Function Warm air is blown to dry the area washed by the shower. (Shows on remote control) 10.Stop Stop warm air dryer, or it will automatically stop after 4 mins. 12.Water temperature control 13.Seat temperature control Press to set water temperature. The temperature shows as a concrete numerical value, When temperature value is between 30-39,water will be heated according to your setting.
20.Energy saving 15.Power Press electricity saving mode can be changed in several mode. When turns on, the whole system goes into electricity saving mode in 1.5 minutes.Functions mentioned above Can be changed in circulation by pressing this button. The electricity saving mode will show on the LCD panel of remote controller. In auto-saving mode, water temperature and seat Temperature remain in 25℃. In 5H–saving mode.
Cleaning and Maintenance Buzzer Cleaning the Toilet Bowl Buzzer Buzz once: Normal operation-receives instructions from the buttons or the remote control Buzz twice: Auto operates when users stand up Buzz three times or above: Indicates malfunction or disorders. Buzzing intervals depends. Do not use corrosive solvents to clean the outside of the toilet, such as banana oil, benzene, decolorizer, cleaner, and diluter.
Daily wash Disassemble filter please use spanner to back-out one touch fitter, take out filter in T valve; turn on the cover of filter to take out filter, please see picture. Daily wash Disassemble and install 1、Take out plug from socket. 2、Turn off inlet valve. 3、Grip the bidet to pull out, separate it with ceramic toilet. 4、Clean surface of bidet and toilet. 5、Reinstall it after clean bidet and toilet. Grip the bidet to slid it into bracket to hear a sound ‘ka’ mean in correct position.
Appendix Product specification Rated power supply AC 110V 60HZ Rated power consumption 1680w (When the inflow water is 5 degrees, set the outflow temperature and strength to the maximum.) Power cord length 1.5m Cleansing and Flushing Water pressure range 0.06Mpa(dynamic)-0.75Mpa(Static) ( flow volume is no less than 18L/min) Water pressure adjustment Adjustable in 4 levels Water Temp.