Intelligent toilet instructions The Product Model: Contents Overall sketch Safety precautions Function introduction 1 2 4 Thanks for choosing our product. And please read the instructions Carefully before properly using.
Safety Precautions Overall sketch All the safety precautions listed can prevent the users from the physical hurts or property losses. Please read all the safety items and warnings, using the product in the right way. Cushion Toilet seat lid WARNING Power plug Ignoring the sign may lead to serious injury or death. Damper Don’t disassemble, repair, alter the product. LED indicator panel Control panel All the behaviors above may lead to fire or electric shock.
Function introduction: WARNING Ignoring the sign may lead to serious injury or death. Functions Don’t stand on the toilet seat cover, seat circle or any other accessories. It may cause break down the product. Don’t drag or bend the water pipe. It may make water leakage or no water supply. Preventing damage from freeze. The inlet tube and the inner of the product may be damaged for freezing, and then lead to water leakage. Don’t put heat instruments beside the substance.
Installation Guide Connecting inlet water Toilet bowl installation Installation environment 1.Before installation, pls connect the angle valve with the pipe Please check that walls and floors in the toilet room are finished construction and there is enough space pre-arranged for sewage, electric wires and water lines. Also please confirm the distance from the closet flange centerline to the fished wall fits for the rough in . And the water supply pressure should be within a range of 0.1MPa (dynamic)-0.
Install the Remote Control Holder Position the toilet Please see below picture 1.Check if the blow off pipe is ok and the ground is clean before you install 2.Put the Gasket on the blow off pipe hole.. 3.Put the toilet on the ground and connect the blow off pipe, adjust the position, make sure the seal ring is workable. 4.Smearing silica gel on the bottom of toilet bowl.(See the picture below) 5.
Operations Operation introduction Product use manual This product is controlled mainly by remote control, while by control panel subsidiary Please note below picture is only for illustration that how LED displays in full screen, not the actual interface. 1.Sitting on the toilet seat seated-sensor activated If air purification is activated,deodorizing function operates automatically. 2.Rear wash Rear cleansing (Icon as below displays in the screen) LED Display (Model 818ZA/725ZA only) 5.
.Dryer Function Warm air is blown to dry the area washed by the shower. 10.Stop Stop warm air dryer, or it will automatically stop after 4 mins. (Shows on remote control) 12.Water temperature control 13.Seat temperature control Press to set water temperature. The temperature shows as a concrete numerical value, When temperature value is between 30-39,water will be heated according to your setting.
20.Energy saving 15.Power Press electricity saving mode can be changed in several mode. When turns on, the whole system goes into electricity saving mode in 1.5 minutes.Functions mentioned above can be changed in circulation by pressing this button. The electricity saving mode will show on the LCD panel of remote controller. In auto-saving mode, water temperature and seat Temperature remain in 25℃. In 5H–saving mode.
Cleaning and Maintenance Cleaning the Toilet Bowl Do not use corrosive solvents to clean the outside of the toilet, such as banana oil, benzene, decolorizer, cleaner, and diluter. Also do not use water to rinsing the equipment as this may cause short circuits,resulting in a fire. Pull out the plug before cleaning in case that plug or the outlet gets wet by water. Scrub the bowl unit gently by soft cloth. If it is very dirty, get the cloth wet and clean the unit by neutral agents. 2.Remove the filter.
Replace the remote control battery Battery installation 1.Use tool to remove remote control and its backside cover. 2.Use tool or coin negatively rotate “+” shape groove, then remove battery cover, do not fall out seal ring. 3.Put button battery into battery hole, upturn battery cathode(with letter side) Replace back up battery Steps: 1.Pull out power plug. 2.Lift toilet seat lid. 3.Take out battery cover. 4.Put battery in right position 5.Press flush button, be sure it can flush normally. 6.
Appendix Product specification Rated power supply AC 110V 60HZ Rated power consumption 1680w (When the inflow water is 5 degrees, set the outflow temperature and strength to the maximum.) Power cord length 1.5m Cleansing and Flushing Water pressure range 0.1Mpa(dynamic)-0.75Mpa(Static) ( flow volume is no less than 18L/min) Water pressure adjustment Adjustable in 4 levels Water Temp.
