Installation Guide

ManualsBrandsDyconn ManualsBathHealth AC Powered Single Hole Touchless Bathroom Faucet in Chrome

Product Features:

Modern design faucets

Water saving control

Lower power consumption

Intelligent sensor control

Stable & Reliable

Sensor Faucet Manual

Models: HF1H21-ORB (Sylvan), HF1H21-CHR (Trinidad)

HF1H22-CHR (Heath), HF1H22-BN (Lawa)

HF1H23-CHR (Nelson), HF1H23-BN (Peace), (HF1H23-ORB) Snake

- Thoroughly read all instructions before installing the enclosed faucet.

- Read and understand all warnings, care and maintenance information

For easy installation of your Dyconn Faucet please do the following:

Summary of content (12 pages)

PAGE 1
Product Features: Modern design faucets Water saving control Lower power consumption Intelligent sensor control Stable & Reliable Sensor Faucet Manual Models: HF1H21-ORB (Sylvan), HF1H21-CHR (Trinidad) HF1H22-CHR (Heath), HF1H22-BN (Lawa) HF1H23-CHR (Nelson), HF1H23-BN (Peace), (HF1H23-ORB) Snake For easy installation of your Dyconn Faucet please do the following: - Thoroughly read all instructions before installing the enclosed faucet.
PAGE 2
PAGE 3
Product Description & Information OPERATION AND MAINTENANCE. CAREFULLY READ THIS INSTRUCTION MANUAL BEFORE INSTALLING AND USING PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE FOR PRODUCT Do not place or install the product directly under the sun or long exposure of sunlight Do not place any catoptric items such as mirror to the opposite wall of the inductive window. Do not use contaminated water with the device. Do not soak the device in water, this will cause permanent damage.
PAGE 4
Product Diagram and Parts Single inlet faucet Models: Hot & cold inlet faucet Models:
PAGE 5
Product Diagram and Parts Single inlet faucet Models: 1. Sensor faucet body 2. Braided hose 3. Self-tapping screw 4. Plastic sleeve 5. Rubber gasket 6. Stainless steel gasket 7. Nut 8. Control box Battery installation 1. When the battery is out, the light sensor will ﬂash in every 2 to 3 sec. 2. Replace the battery by taking oﬀ the cover and replace new battery. *** Main control unit can be powered by AC or battery alone.
PAGE 6
Control Box Single inlet control box Single inlet control box Clean ﬁlter : 1. Disconnect the power plug. 2. Turn oﬀ waterway. 3. Take out ﬁlter screen with a plier. 4. Clean ﬁlter screen gently with running water and replace the screen. Connect the power. Terminal port Power plugs outlet *** Hot/cold water mixing valve can be purchased.
PAGE 7
Installation - Single inlet faucet Single inlet faucet 1. Connect with water inlet hose. 2. Put the hoses into basin sink hole 3. Fix the sensor faucet body with ﬁller pieces and nut. 4. Hang the control box on the wall ﬁxture a. Drill two wall holes, and insert the plastic expansion sleeve and screws.
PAGE 8
5. Connect faucet hose to outlet part on control box. Connect inlet port on control box to pretempered water supply. Connect faucet sensor power cord to control box. Make sure everything is secured then connect control box power cord to power outlet. 6. ***Optional: hot/cold water mixing valve can be purchased. See control box ﬁgure (pg.4) . Please test the water temperature before installation, hot water may cause serious burn.
PAGE 9
Installation - Hot & Cold faucet Hot & cold inlet faucet Models: 1 1. Connect with water inlet hose. 2. Put the hoses into basin sink hole. 3. Fix the sensor faucet body with ﬁller pieces and nut. 4. Connect the hot and cold ﬂexible hoses to water supply valves. 4a. Connect electric wire A-B ; C-D Hang the batteries box on the ﬁxed nut. Make sure everything is secured then connect control box power cord to power outlet. 5. Do not connect wires A-D directly.
PAGE 10
Sensor Adjustment & Troubleshooting Sensor Adjustment 1. Turn oﬀ the water circuit and remove the faucet from the counter sink . 2. Use a clamp pliers to pick oﬀ the sponge which is at the back of the sensor display. 3. Take the controller out, along the potentiometer and adjust lightly. Turning clockwise will increase the inductive distance, turning anti-clockwise will decrease the inductive distance.
PAGE 11
PAGE 12