User's Manual Part 2
WWW.DYEPA I NTBALL.C O M
SOLENOID WILL NOT ACTIVATE / TRIGGER NOT
WORKING
• Check that the trigger adjustment is not set so that the
micro switch cannot activate. You should hear a small
click when pulling the trigger.
your trigger is set so that the micro switch is always
activated. Re-adjust the trigger.
• Check that the solenoid cable is attached to the board
and to the correct connector (solenoid should be
attached to the two-prong connector).
• Check the Dwell is set correctly (see page 5).
TRIGGER BOUNCE / M2 SHOOTING MORE THAN
ONE BALL PER PULL IN SEMI-AUTOMATIC MODE
mode.
• Check that the trigger is not adjusted too short.
ERRATIC VELOCITY / M2 WON’T FIRE
M2 FIRES BUT BALLS ARE DROPPING OFF OR NOT
EVEN COMING OUT OF THE BARREL
• Make sure the battery is charged.
• Raise the dwell to factory level (15).
• Make sure bolt is well lubed and moves well. If there is
too much friction in the bolt it will cause the M2 to
shoot down. Replace O-rings causing this excess
friction.
• Make sure air system is screwed in all the way.
• Reset LPR to stock setting.
• Make sure Hyper5
™
is set correctly.
FIRST SHOT IS TOO HIGH
• Change the seat inside the Hyper5
™
Regulator.
For disassembly instructions consult page 18 in
the technical section.
• Check that the 014 O-ring on the inside of the
top hat is in place and in good condition.
VELOCITY IS NOT CONSISTENT
well and are consistent in size. You should be able to
blow the paintball through the barrel but they should
not roll through the barrel on their own.
• Remove the bolt kit and re-lube it. Change any O-rings
causing a lot of friction. Make sure 014 O-ring in bolt
tip is in place and in good condition.
• Raise the dwell.
• Check that the Hyper5
™
regulator is working correctly
and that the pressure is consistent.
• Disassemble and change worn out O-rings and the
regulator seat in the Hyper5
™
regulator.
• Check that the LPR pressure is not set too low.
See pages 7 & 19 for instructions on how to set your
LPR pressure.
• Replace the seat in LPR (see instructions on page 20).
TROUBLE SHOOTING GUIDE
26
FEDERAL COMMUNICATION COMMISSION
INTERFERENCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a partic-
ular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment
o and on, the user is encouraged to try to correct the interference by one
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modi cations not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
RADIATION EXPOSURE STATEMENT:
The product comply with the FCC portable RF exposure limit set forth for
an uncontrolled environment and are safe for intended operation as de-
scribed in this manual. The further RF exposure reduction can be achieved
if the product can be kept as far as possible from the user body or set the
device to lower output power if such function is available.
Operating Frequency:2402~2480MHz
RADIATION EXPOSURE STATEMENT(WPC):
The product comply with the FCC/IC RF Exposure for Low Power
Consumer Wireless Power Transfer.
RF exposure limit set forth for an uncontrolled environment and are
safe for intended operation as described in this manual.
The further RF exposure that compliance was demonstrated at
10cm and greater separation from the user body or set the device
to lower output power if such function is available.