user manual

ManualsBrandsDymo ManualsClockClock DATEMARK

In Program mode,

change eld values.

Select message to print.

In program mode, move

between elds.

Set alarm.

Set a security

code to lock your

stamper settings.

Change

stampersettings.

Select elds

to print.

DISTRIBUTED BY/DISTRIBUÉ PAR:

IMPORTED INTO CANADA BY/IMPORTÉ AU CANADA

PAR SANFORD CANADA L.P., OAKVILLE, ON L6J 3J3

Getting Started

Inserting the Batteries

1 Press the thumb latch on

the back of the stamper

to remove the battery

compartment cover.

2 Insert four AA batteries

following the polarity

markings (+ and -).

3 Using a coin, remove

the lithium cell battery

compartment cover.

4 Remove the safety

ribbon and make sure

the positive (+) side of

the battery is facing up.

5 Replace the lithium cell

battery compartment

cover. Use a coin to

lock the cover in place.

6 If the LCD display

ashes P-RESET,

use a ballpoint pen to

press the reset button.

7 Replace the battery

compartment cover.

Setting the Date and Time

1 Press and hold the SET/EDIT button for 2

seconds.

The stamper enters Program mode and the

Month (M) and Day (D) indicators begin ashing.

If no keys are pressed for 10 seconds, the

stamper returns to Normal mode.

2 Press the LOCK button to cycle through the

available date formats.

3 Select one of the following date formats, and

then press the SHIFT button.

• MM-DD-YY

• YY-MM-DD

• DD-MM-YY

4 To set the value for the rst eld, do the

following:

• To increase the value, press the

LOCKbutton.

• To decrease the value, press and hold the

LOCK and SHIFT buttons for 5 seconds,

and then press the LOCK button to

decrease the value.

5 Press the SHIFT button to move to the next eld.

6 Repeat steps 4 and 5 to set the value for

eacheld.

7 Press the SET/EDIT button to return to

Normalmode.

3 Press the SHIFT button to move to the

nextdigit.

4 Repeat steps 2 and 3 for each digit.

5 Press the SECURITY CODE button to unlock

the stamper and return to Normal mode.

The key icon disappears from the display.

If you have forgotten the security code, remove

and replace the lithium cell battery to reset the

code. Removing the lithium cell battery resets all

stamper settings.

Resetting the Stamper

If the AA batteries are low or there is a printer error,

the display will ash P-RESET. The stamper will not

print while P-RESET is ashing. You must reset the

stamper in order to print.

1 Press the thumb latch on

the back of the stamper

to remove the battery

compartment cover.

2 Use a ballpoint pen to

press the PRINTER

RESET button.

The printing belt is reset.

If you do not hear the printing belt reset,

replace the four AA batteries and press the

PRINTER RESET button again.

Maintaining the Stamper

To maintain your stamper at peak operating

performance, follow these guidelines:

 Do not touch the print head or belt when the

unit is printing. This will cause the printer to

malfunction and require servicing.

 If printer speed slows down, replace all four

AA batteries. Operating the stamper with low

batteries will damage the stamper.

 Immediately replace the lithium cell display

battery if BATT appears in the display.

 Always cover the battery compartment

beforeprinting.

 Keep stamper away from moisture.

 Avoid placing stamper in direct sunlight.

 Before printing, ensure paper surface is dust

free and print head is clean.

 When printing, place the paper on an

evensurface.

 To clean the exterior of the stamper and the

battery compartment, wipe with a lint-free

cloth. Remove dirt and smudges using a cotton

ball and alcohol.

 Ensure surroundings are clean and free of

dust before performing maintenance on the

stamper.

 Perform stamper maintenance every three

months to prevent particle accumulation on the

print head.

 Using tweezers, carefully remove any dried ink

from the roller and then clean using a lint-free

cloth or cotton ball and alcohol.

 Clean stamper before storing if the stamper will

not be used for an extended period of time.

Maintaining the Battery

The stamper checks the status of the display

battery every hour. If the lithium cell display battery

is low, BATT appears in the display.

IMPORTANT: If BATT appears in the display,

change the lithium cell battery immediately.

Operating the stamper on a low display battery

may cause damage to the stamper.

Relling the Ink Roll

1 Remove the ink roll compartment cover.

2 Using tweezers or a paper

clip, rotate the ink roll

counter-clockwise and

pull the ink roll to remove

from the stamper.

3 Apply a few drops of ink

pad ink on the ink roll.

4 Carefully insert the ink

roll in the proper position

inside the stamper.

5 Replace the ink roll

compartment cover.

Selected Fields

Display Example

Date and Time

26-12-12 P12:38

Date, Time,

and Message

26-12-12 P12:38 RCVD

Date, Message,

and 4-digit counter

26-12-12 RCVD 1234

Date and

6-digit counter

26-12-12 000456

Message

IN OUT PAID FILE REFERENCE CONFIRMED RECEIVED

Abbreviation

IN OUT PAID FILE REF: CFMD RCVD

Selecting the Fields to Print

You can print any combination of the

followingelds:

 Date

 Time

 Message

You can also choose to print any of the two elds

above and a 4-digit counter or any one of the elds

above with a 6-digit counter.

1 Press and hold the PRINT SELECT button for

2 seconds.

The date eld begins ashing.

2 Press the SET/EDIT button to select or not

select to print the eld.

3 Press the PRINT SELECT button to move to

the next eld.

4 To select to print the date, do the following:

a Press the SET/EDIT button until a rectangle

is displayed around DATE in the display.

b Press the PRINT SELECT button to move

to the next eld.

5 Repeat step 4 for each remaining eld.

6 Press the ALARM MODE button to return to

Normal mode.

Selecting the Message to Print

When you select to print the message eld, you

can also select which message to print.

` Press the SHIFT button to select the message

to print.

Each time you press the SHIFT button, the

next available message is selected.

Printing

1 Set the stamper on a clean, at surface.

2 Rock the stamper forward and push down on

the top of the stamper.

The stamper prints the selected elds.

3 When you hear that printing has nished,

release pressure on the stamper.

Using Auto-Numbering

Setting Auto-Numbering

You can print a 4-digit or 6-digit counter. A 4-digit

counter can be combined with any two additional

elds. A 6-digit counter can be combined with any

one additional eld.

1 Press and hold the PRINT SELECT button for

2 seconds.

The date eld begins ashing.

2 Press the PRINT SELECT button until the

desired counter type is ashing.

• 4-DIGIT - counts up

• q 6-DIGIT - counts down

• 6-DIGIT p - counts up

3 Press the SET/EDIT button until a rectangle is

displayed around the selected counter.

4 To set the rst digit, do the following:

a Press the LOCK button to increase

thevalue.

b Press the SHIFT button to move to the

nextdigit.

5 Repeat step 4 for each digit.

6 Press the ALARM MODE button to return to

Normal mode.

Locking Auto-Numbering

You can choose to lock auto-numbering so that

the counter does not automatically increment to

the next number after each printing.

` Press the LOCK button.

CNTLOCK appears in the display.

To unlock auto-numbering, press the

LOCK button again.

Using the Alarm

Setting the Alarm

1 Press the ALARM MODE button.

The alarm indicator begins ashing.

2 Press the LOCK button to activate the alarm.

The alarm icon appears in the display.

3 Press the SET/EDIT button while the alarm

indicator is still ashing.

The hour eld begins ashing.

4 Press the LOCK button to set the hour, and

then press the SHIFT button.

5 Press the LOCK button to set the minute.

6 Press the ALARM MODE button to save the

alarm settings and return to Normal mode.

When the alarm sounds, press the ALARM MODE

button to stop the alarm.

Turning Off the Alarm

1 Press the ALARM MODE button.

The alarm indicator begins ashing.

2 Press the LOCK button to deactivate the alarm.

The alarm icon disappears from the display.

Using a Security Code

To prevent unauthorized changing of stamper or

counter settings, you can use a four digit security

code to lock your stamper.

Locking the Stamper

1 Press and hold the SECURITY CODE button

for 2 seconds.

The rst digit of the security code begins

ashing.

2 Press the LOCK button to set the rst digit.

3 Press the SHIFT button to move to the

nextdigit.

4 Repeat steps 2 and 3 for each digit.

5 Press the SECURITY CODE button to lock the

stamper and return to Normal mode.

A key icon appears in the display.

Unlocking the Stamper

1 Press and hold the SECURITY CODE button

for 2 seconds.

2 Press the LOCK button to select the rst digit

of the code.

W010793

Summary of content (2 pages)

PAGE 1
Getting Started Setting the Date and Time 1 Press and hold the SET/EDIT button for 2 seconds. The stamper enters Program mode and the Month (M) and Day (D) indicators begin flashing. Inserting the Batteries 1 Press the thumb latch on the back of the stamper to remove the battery compartment cover. If no keys are pressed for 10 seconds, the stamper returns to Normal mode. 2 Insert four AA batteries following the polarity markings (+ and -).
PAGE 2
Mise en route Insertion des piles 1 Appuyez sur le loquet à poucier à l'arrière de l'horodateur pour retirer le couvercle du compartiment à piles. 2 Insérez quatre piles AA en respectant la polarité (+ et -). 3 À l'aide d'une pièce de monnaie, retirez le couvercle du compartiment de la pile au lithium. 4 Retirez le ruban de sécurité et assurez-vous que le côté positif (+) de la pile est tourné vers le haut. 5 Remettez en place le couvercle du compartiment de la pile au lithium.