User guide

ManualsBrandsDymo ManualsPrinterLabelPOINT 350

About Your New Labelmaker

With your new DYMO LabelPOINT

™

350

labelmaker, you can create a wide variety of high-

quality, self-adhesive labels. You can choose to

print your labels in many different sizes and styles.

The labelmaker uses DYMO D1 label cassettes in

widths of 6 mm (1/4”), 9 mm (3/8”), 12 mm (1/2”),

or 19 mm (3/4”). Label cassettes are also available

in a wide range of colors.

Visit www.dymo.com for information on obtaining

tapes and accessories for your labelmaker.

Warranty Registration

Please complete the warranty registration card and

return it to the appropriate customer service

address within seven days. Visit www.dymo.com

for details.

Getting Started

Follow the instructions in this section to print your

first label.

Connecting the Power

The labelmaker is powered by standard batteries, a

rechargeable battery pack, or an AC power

adapter. To save power, the labelmaker will

automatically turn off after two minutes of inactivity.

Inserting the Batteries

The labelmaker uses six AA batteries.

To insert the batteries

1. Remove the battery compartment cover. See

Figure 2.

Figure 2

2. Insert the batteries following the polarity

markings (+ and –).

3. Replace the battery compartment cover.

Remove the batteries if the labelmaker will

not be used for a long period of time.

Using the Battery Pack

An optional, rechargeable battery pack can be

used to power the printer. The battery pack can be

purchased through your local DYMO reseller.

The printer must be connected to external power

through the AC adapter to charge the battery pack.

When the battery pack is completely discharged,

allow four to 2 hours to fully charge the battery.

When connected to external power, the

battery charging indicator may continue to display

even though the battery pack is fully charged.

To use the battery pack

1. Open the battery compartment door.

2. Insert the battery pack. See Figure 3.

Figure 3

3. To charge the battery pack, connect the AC

adapter as described below.

Summary of content (14 pages)

PAGE 1
GB About Your New Labelmaker With your new DYMO LabelPOINT™ 350 labelmaker, you can create a wide variety of highquality, self-adhesive labels. You can choose to print your labels in many different sizes and styles. The labelmaker uses DYMO D1 label cassettes in widths of 6 mm (1/4”), 9 mm (3/8”), 12 mm (1/2”), or 19 mm (3/4”). Label cassettes are also available in a wide range of colors. Visit www.dymo.com for information on obtaining tapes and accessories for your labelmaker.
PAGE 2
Connecting the Power Adapter An optional AC power adapter can also be used to power the labelmaker. Connecting the AC adapter to the labelmaker disconnects the batteries as a power source. To connect the power adapter 1. Plug the power adapter into the power connector on the top, left side of the labelmaker. 2. Plug the other end of the power adapter into a power outlet. Make sure the labelmaker power is turned off before you disconnect the power adapter from the main power source.
PAGE 3
Settings Power You can select the language and corresponding units of measure you want the labelmaker to use. The A button turns the power on and off. After two minutes of no activity, the power is switched off automatically. The last label created is remembered and displayed when the power is turned back on. The previously selected style settings are also restored. Getting to Know the Labelmaker Style Scroll Bar # of Copies Font Mixed Formats You are now ready to print your first label.
PAGE 4
CAPS Mode Connecting to Your Computer The # key toggles capitalization on and off. When CAPS mode is turned on, the CAPS mode indicator is shown on the display and all letters that you enter will be capitalized. The default setting is CAPS mode on. When CAPS mode is off, all letters entered appear in lower case. Your labelmaker can be used as a standalone label printer or you can print labels from your computer using the DYMO LabelMANAGER software.
PAGE 5
When you select a font, that font applies to all characters on a page. If you want to use more than one font, you must insert format breaks. See Using Mixed Formats on page 8 for more information. To set the font 1. Press the key. 2. Use the arrow keys to move to the desired font and then press OK . Styles can be used with all alphanumeric characters and symbols. See Using Symbols and Special Characters on page 8 for more information on printing symbols. To set the font style key. 1. Press the 2.
PAGE 6
A label can be underlined or enclosed in a box or background, but not both together. To set the box style 1. Press the key. 2. Select a frame style and then press OK . On multi-line labels, all lines are underlined. However, all the lines are enclosed in a box style.
PAGE 7
To add a symbol 1. Press Symbols . The first row of symbols shown in the table appears in the display. 2. Use the arrow keys to move to the desired symbol. The left and right arrows move horizontally along a row of symbols. The up and down arrow keys scroll vertically through the rows of symbols. To quickly see a row of symbols, you can press the letter corresponding to the row you want. 3. When you locate the desired symbol, press OK to add the symbol to your label text.
PAGE 8
Printing Multiple Copies You can print up to 16 copies of a label at one time. When printing multiple copies, a dotted cut-line is printed between each label. To print multiple copies of the label Memory 1. Press Settings and then select Set # Copies. 2. Press the up arrow key to increase the number of copies to print. 3. Press the down arrow key to begin decreasing the number of copies from 16. 4. Press OK . 5. Press G to begin printing.
PAGE 9
4. One or more question marks appear between the barcode symbols ( ). ???????0 You may see a 0 in the far right position for some barcode types. This is a check digit and will be replaced with a number when the barcode data is entered. 5. Enter the data for the barcode, replacing the question marks, and press OK when finished. To insert a barcode 1. Enter the text you wish to appear before the barcode on the label. (optional) 2. Press Insert . 3. Use the arrow keys to select Insert Barcode and press OK .
PAGE 10
Storing Formats Caring for Your Labelmaker In addition to label text, you can store up to ten specific label formats you use frequently. This feature stores only the formatting information not the label text. To store the current format Memory 1. Press 8 + Settings . 2. Select SAVE and then FORMAT. The first of ten memory fields is displayed. 3. Use the arrow keys to move through the fields.
PAGE 11
Troubleshooting Review the following possible solutions if you encounter a problem while using your labelmaker. Problem/Error Message Solution No display • Ensure the labelmaker is turned on. • Replace discharged batteries. Poor Print Quality • • • • Poor Cutter Performance Clean the cutter blade. See Caring for Your Labelmaker. Printing No action required. Message disappears when printing is finished. Replace discharged batteries or attach power adapter.
PAGE 12
Documentation Feedback We are constantly working to produce the highest quality documentation for our products. We welcome your feedback. Send us your comments or suggestions about our user guides.
PAGE 13
15
PAGE 14
16